Panasonic CQ-C1301NW Operating Instructions page 2

General
[VOL] (Volume) Remote control sensor
for an optional remote control unit (CA-RC61EX).
BAND CQ-C1321N
APM
PWR
PTY
MUTE/SQ SCROLL RANDOM SCAN REPEAT TA/AF
SRC SRC DISP
1 2 3 4 5 6
[SRC] (Source) [MUTE]
selects a source. toggles mute on/off.
(PWR) (Power) (SQ) (Sound Quality)
toggles power on/off. selects a sound type (SQ). (Hold it down for
more than 1 second.)
Power On/Off SQ (Sound Quality)
Set your car's ignition switch to the ACC or ON position. SQ is a function that can call up various sound types at the
touch of button in accordance with your listening music
Power on: Press [SRC] (PWR).
type.
Power off: Hold down [SRC] (PWR) for 1
Holding down [SQ] for more than 1 sec-
more than 1 second.
ond activates the SQ selection mode.
Source Selection 2
Press [SQ] to select the sound type (SQ)
Press [SRC] to change the source. as follows:
(FLAT) flat frequency response:
Radio Disc Player
does not emphasize any part. (Default)
(ROCK) speedy and heavy sound:
Volume Adjustment
exaggerates bass and treble.
(Setting Range: 0 to 40, Default: 18)
Turn [VOL]. (POP) wide-ranged and deep sound:
slightly emphasizes bass and treble.
Mute
(VOCAL) clear sound:
ON: Press [MUTE]. ( lights.) emphasizes middle tone and slightly empha-
sizes treble.
OFF: Press [MUTE] again.
Notes:
¡ If no operation takes place for more than 5 seconds in
the SQ selection mode, the display returns to the regular
mode.
¡ Settings of SQ, bass and treble are influenced one anoth-
er. If such an influence causes distortion to the audio
signal, readjust bass/treble or volume.
Troubleshooting
If You Suspect Something Wrong
Warning
Check and take steps as described below.
If the described suggestions do not solve the problem, it is recom- ¡ Do not use the unit in an irregular condition, for example, with-
mended to take the unit to your nearest authorized Panasonic Service out sound, or with smoke or a foul smell, which can cause
ignition or electric shock. Immediately stop using the unit and
Centre. The product should be serviced only by qualified personnel.
consult your dealer.
Please refer the checking and the repair to professionals. Panasonic
¡ Never try to repair the unit by yourself because it is dangerous
shall not be liable for any accidents arising out of neglect of checking
the unit or your own repair after your checking. to do so.
Trouble Check point Trouble Check point
Common Radio
● Start the engine. (Or turn the ignition ●
Tune in to another station of high-inten-
switch to the ACC position.) Frequent sity waves.
● ●
Verify the wiring. (battery lead, power noise Make sure that the antenna mounted
lead, ground lead, etc.) point is grounded properly.
No power
●
Fuse blown (Contact the nearest
●
Panasonic Service Centre.) The preset memory is cleared to return
● Preset data
Ask a professional for fuse replacement. to the original factory setting when the
●
Be sure to use the same rated fuse. deleted power connector or battery is discon-
nected.
●
Disable the mute function.
●
Verify the wiring.
No sound
●
Wait until the dew disappears before
Error Display Messages
turning on the unit.
(The disc is ejected automatically.)
● Make sure that grounding is established
The disc is dirty, or is upside down.
Noise
properly.
●
Check the disc.
No sound from
● Adjust the balance and fader. (The disc is ejected automatically.)
left, right, front,
● The disc has scratches.
Verify the wiring.
or rear speaker
● Check the disc.
Left and right
sounds are ● Connect the speaker lead correctly.
No operation by some cause.
reversed ● If normal operation is not restored, con-
sult your dealer or the nearest Service
Centre to ask for repairs.
Disc Player
No sound, or disc
●
Load the disc correctly.
Cannot read the file
is automatically
●
Clean the disc. ●
Check the file.
ejected
Sound skip,
A WMA file can be copyrighted.
●
poor sound Clean the disc. ●
The file protected by copyright is not
quality
playable.
Sound skip ● The maximum permissible tilt angle is
due to 30°.
● Secure the unit.
vibration
● Press [ u ]. If the disc is still not ejected,
Disc not
contact the nearest Panasonic Service
ejectable
Centre.
Radio (AM [LW/MW]/FM)
[BAND]
selects a band in the radio source.
(APM) ( Auto Preset Memory)
executes APM in the radio source. (Hold it
down for more than 2 seconds.)
BAND BAND CQ-C1321N
APM
PWR PTY
MUTE/SQ SCROLL RANDOM SCAN REPEAT TA/AF [DISP] (Display)
SRC SRC DISP DISP
1 1 2 2 3 3 4 4 5 5 6 6
switches the information on
the display.
[SRC] (Source) [1] to [6] [TUNE ]] [TUNE []
selects a source. selects a preset station in the radio source, down/up the frequency. (Hold it down for
and presets the current station. (Hold it down more than 0.5 seconds and release it for seek
for more than 2 seconds.) tuning.)
1 3
Press [SRC] to select the radio source. Select a station.
2
Press [BAND] to select a band.
Frequency adjustment
[TUNE ]]: Lower
[TUNE []: Higher
Note: Hold down either of them for more than 0.5 sec-
onds and release it for seek tuning.
Preset station selection
Press the corresponding preset button from [1] to [6] to
tune into a preset station.
Radio Data System (RDS) in FM Broadcasting
Useful functions such as AF, TA, PTY are available in the RDS (Radio Data System)-ready areas.
Some FM stations are broadcasting added data compatible ¡ Setting to TA on with the unit in another mode, it will auto-
with RDS. This radio set offers convenient functions using matically switch to radio mode and output the traffic
such data. announcement when the traffic announcement begins. The
traffic announcement having finished, the unit will return to
RDS service availability varies with areas. Please understand if
RDS service is not available in your area, the following service the previous mode. (TA Standby Mode)
is not available, either. PTY (Programme Type)
The following functions are available when receiving RDS
The following functions are available when the PTY mode is
stations.
active.
AF (Alternative Frequency)
¡ The PTY of receiving station appears.
The following functions are available when the AF mode is
¡ Programs can be searched for by PTY.
active ( lights).
Note: PTY language can be selected. (a "Function Settings")
¡ When receiving conditions become bad, a station with bet-
ter receiving conditions is automatically tuned in to. Other functions of RDS
¡ When executing APM, only RDS stations are selected.
CT (Clock Time)
¡ When calling up a preset station, a best receiving station is
selected automatically. (BSR Best Stations Research) The clock is automatically adjusted.
PS (Programme Service Name)
Notes:
As well as the frequency, the name of the broadcast station
¡ The AF sensitivity can be adjusted. appears.
¡ The AF available range can be adjusted. (a "Function
EON (Enhanced Other Network)
Settings")
RDS information is updated constantly in response to the
current position.
TA (Traffic Announcement)
EON-TA
The following functions are available when the TA mode is active Traffic information from the current and other network
( lights). stations can be received.
A TP station is automatically searched for and received at
¡ Emergency Announcement Reception
the instant of toggling the TA mode on if you are receiving Emergency announcement automatically appears on the
a non-TP station or TP station with poor reception. display when it is received.
¡ When executing station search or APM, only TP stations
are selected.
AF Level PI Seek (Programme Identification Seek)
Hold down [TA] (AF) for more than 2 seconds to select AF If reception becomes poor when tuning in a preset station,
level. press the same preset number button. The same station with
better reception will be searched for.
Press same preset number button again to cancel.
Low level AF operating sensitivity. (Default)
High level AF operating sensitivity. Note: For PI Seek, cancel the TA mode first, then execute PI
Seek.
When the AF network of an RDS station is not
required.
Disc Player
Disc slot
lights while receiving an FM stereo signal.
Display change
takes a disc in with the printed side facing
up.
Frequency Preset Number
Band Press [DISP] to change the display.
Notes:
AM (LW/MW) mode: ¡ The power will be turned on automatical-
ly when a disc is loaded at ACC ON.
Band/frequency
¡ A disc which has both CD-DA data and
MP3/WMA data on it may not be repro-
CT (Clock Time)
duced normally.
FM (not RDS) mode:
Band/frequency
PS
(y / 5) (Pause/Play)
toggles pause/play in the
player source.
CT
RDS mode:
PS (Programme Service name) [SRC] (Source)
selects a source.
Band/frequency
CT
Caution
¡ Do not insert a disc when the
Up to 6 stations can be preset in AM (LW/MW), FM1, FM2, and
Manual station preset
¡ Refer to the section of "Notes on Discs" and "Notes on
FM3 respectively.
MP3/WMA".
1
Preset stations can be simply called up by pressing one of the
Tune into a station.
¡ This unit does not support 8 cm discs.
preset buttons from [1] to [6].
2
Hold down one of the preset buttons from
Auto Preset Memory (APM) [1] to [6] for more than 2 seconds.
With this operation, stations with good receiving conditions can
be automatically stored in the preset memory.
1
Select a band.
(blinks once)
2
Hold down [BAND] (APM) for more than 2
Note: New stations overwrite existing saved stations.
seconds.
The preset stations under best receiving conditions are
received for 5 seconds each after presetting the stations
(SCAN). To stop scanning, press one of the buttons from
[1] to [6].
Note: New stations overwrite existing saved stations.
Audio Settings
TA On/Off Traffic Information Only (TA Mute) [VOL] (Volume)
selects a value in the audio menu.
Pressing [TA] toggles TA on and off. For listening to only traffic information, activate TA and set the
(PUSH SEL) (Push to select)
volume to 0 in FM mode.
selects items in the audio menu.
Once traffic information starts, the volume changes to the TA
volume. (a "Audio Settings")
PTY On/Off Detailed PTY Selection
Holding down [DISP] (PTY) for more than 2 seconds toggles 1
Press []] or [[] to select PTY.
PTY mode on and off.
SPEECH / MUSIC / NEWS / AFFAIRS /
INFO / SPORT / EDUCATE / DRAMA /
CULTURE / SCIENCE / VARIED / POP M /
Programme Search by PTY
ROCK M / EASY M / LIGHT M / CLASSICS /
OTHER M / WEATHER/ FINANCE / CHILDREN /
Programs can be searched for by use of PTY that has been
SOCIAL / RELIGION / PHONE IN / TRAVEL /
originally preset.
LEISURE / JAZZ / COUNTRY / NATION M /
Press [1] to [6] to select PTY in the PTY mode. OLDIES / FOLK M / DOCUMENT
Programme Type Contents
2
Press [BAND].
1 NEWS NEWS
2 SPEECH AFFAIRS, INFO, EDUCATE, Search starts.
DRAMA, CULTURE, SCIENCE,
VARIED, WEATHER, FINANCE,
Notes:
CHILDREN, SOCIAL, RELIGION,
¡ To stop searching, press [BAND] (SET).
PHONE IN, TRAVEL, LEISURE,
DOCUMENT ¡ When there is no corresponding programme type station,
3 SPORT SPORT "NONE" is displayed.
4 POP M POP M
5 CLASSICS CLASSICS
PTY Preset Change
6 MUSIC ROCK M, EASY M, LIGHT M,
OTHER M, JAZZ, COUNTRY,
Original PTY presets can be changed as you like.
NATION M, OLDIES, FOLK M
1
Select a PTY that you would like to preset.
Another station in the same PTY is searched for by pressing
2
Follow the procedure of ordinary presetting.
[BAND].
( "Station Preset" in "Radio (AM
a
Notes:
[LW/MW]/FM)")
¡ When there is no corresponding programme type station,
"NONE" is displayed.
¡ A desired PTY appears for 5 seconds.
¡ Preset contents are changeable.
[6] [7]
skip to the previous/next track/file in the player
mode.
Hold down either of them for fast reverse/fast for-
ward.
[u] (Eject)
ejects the disc.
BAND BAND CQ-C1321N
APM
PWR
PTY
[DISP] (Display)
SRC SRC MUTE/SQ SCROLL RANDOM SCAN REPEAT TA/AF DISP DISP
1 2 3 3 4 4 5 5 6 6
switches the information on the
display.
[ } ] [ { ]
indicator
skip to the previous/next folder.
(RANDOM)/(SCAN)/(REPEAT)
toggles on/off each play mode.
(SCROLL)
scrolls the information on display.
¡ If you insert an 8 cm disc and cannot eject it, turn ACC of your car
indicator lights.
off once and turn it on again, then press [u] (Eject).
¡ Do not insert foreign objects into the disc slot.
1 Folder selection (MP3/WMA)
Press [SRC] to select the Disc Player
source.
Press [ { ] / [ } ].
2
Select a desired portion.
Pause
Track/file selection
Press [BAND] (y / 5).
Press [6] / [7].
Press again to cancel.
Note: To perform fast forward/reverse, hold down either
of them.
Disc Player (CD-DA disc):
Previous/next track
Disc Player (MP3/WMA disc):
Previous/next file
Function Settings
[VOL]
selects a value in the function menu.
(PUSH SEL) (Push to select)
selects items in the function menu.
BAND CQ-C1321N
APM
PWR PTY
MUTE/SQ SCROLL RANDOM SCAN REPEAT TA/AF
SRC DISP DISP [DISP] (Display)
1 2 3 4 5 6
exits from the audio menu.
1
Press [VOL] (PUSH SEL) to display the audio menu display.
Note: If no operation takes place for more than 7 seconds in the audio menu (2 seconds in Main volume adjust-
ment), the display returns to the regular mode.
2 3
Press [VOL] (PUSH SEL) to select a Turn [VOL] clockwise or counterclock-
mode to be adjusted. wise to adjust.
Volume
(Setting Range: 0 to 40, Default: 18) q : Up
w :
Down
Bass
q :
(Setting Range: –12 dB to +12 dB by 2 dB, Increased
w :
Default: 0 dB) Decreased
Treble
(Setting Range: –12 dB to +12 dB by 2 dB, q :
Increased
Default: 0 dB) w : Decreased
Balance
(Setting Range: 15 levels each, Default CNT (cen- q :
Right enhanced
tre)) w : Left enhanced
Fader
(Setting Range: 15 levels each, Default CNT (cen- q : Front enhanced
tre)) w : Rear enhanced
External Mute
Allows you to mute the current source while q : Increased
w :
Panasonic navigation system provides voice guid- Decreased
ance or car telephone conversation is in progress.
(Setting Range: 0 (no sound), 1 (decrease 15
steps), 2 (decrease 10 steps) and OFF
(unchanged), Default: 0)
TA Volume Set
(Setting Range: 1 to 40, Default: 18) q :
Increased
w : Decreased
Note: If the fader is set to front, the pre-amp. output (rear) is decreased.
CD-DA mode display Display change
Track number Play time
Press [DISP] to change the display.
Disc Player (CD-DA disc): Disc Player (MP3/WMA disc):
Normal Normal
Disc title Play time
Play Mode indicators
Track title Folder name/
MP3/WMA mode display Album*
Clock File name/
lights when folder random/repeat/scan is on.
Title, artist*
Folder number File number
Clock
*ID3/WMA Tag On/Off
Hold down [3] for more
than 2 seconds.
Play Mode indicators
album title and song title/
artist name are displayed.
(Default)
folder name/file name are
displayed.
Notes:
¡ For scrolling text, press [3] (SCROLL).
¡ "NO TEXT" is displayed when there is no information on the
disc.
Random play Folder repeat play (MP3/WMA)
All the available songs (tracks/files) are played in a random The current folder is repeated.
sequence. Hold down [6] (REPEAT) for more than 2
Press [4] (RANDOM).
seconds.
Press again to cancel.
Hold down again to cancel.
Folder random play (MP3/WMA)
Scan play
All the available files in current folder are played in a random
The first 10 seconds of each songs (tracks/files) is played in
sequence.
sequence.
Hold down [4] (RANDOM) for more than 2
Press [5] (SCAN).
seconds.
Press again to cancel.
Hold down again to cancel.
Folder scan play (MP3/WMA)
Repeat play
From the next folder, the first 10 seconds of the first file on
The current song (track/file) is repeated. each folder is played in sequence.
Press [6] (REPEAT). Hold down [5] (SCAN) for more than 2
seconds.
Press again to cancel.
Hold down again to cancel.
BAND CQ-C1321N
APM
PWR PTY [DISP] (Display)
MUTE/SQ SCROLL RANDOM SCAN REPEAT TA/AF
SRC DISP DISP
1 2 3 4 5 6 exits from the function
menu.
1
Hold down [VOL] (PUSH SEL) for more than 2 seconds to display the function menu dis-
play.
Note: If no operation takes place for more than 7 seconds in the function menu, the display returns to the regular
mode.
2 3
Press [VOL] (PUSH SEL) to select a Turn [VOL] clockwise or counterclockwise
mode to be adjusted. to adjust.
MONO OFF
FM Monaural FM
Noise is significantly decreased when weak signals are
received from an FM broadcast station. MONO ON
( lights.)
(Default: OFF)
LOCAL OFF
FM Local FM
Only stations with good reception are detected in seek
tuning. LOCAL ON
( lights.)
(Default: OFF)
LOCAL OFF
AM Local AM
Only stations with good reception are detected in seek
tuning. LOCAL ON
( lights.)
(Default: OFF)
Set to OFF if your car has no
ACC Selection
ACC position.
(Default: OFF)
(a "Preparation") Set to ON if your car has an
ACC position.
The frequency is changed
Region RDS
also for programs outside the
region.
(Default: OFF)
Note: When the Region mode is switched from OFF to The frequency is changed
only for programs within the
ON or vice versa, the AF mode turns on automatically.
region.
English
PTY Language
RDS
(Default: ENGLISH)
Swedish