Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Packard Bell Viseo243D
Summary of Contents for Packard Bell Viseo243D
- Page 1 Packard Bell LCD Monitor User Guide...
- Page 2 Date of purchase: ________________________________ Place of purchase: ________________________________ Packard Bell and the Packard Bell logo are registered trademarks of Acer Incorporated. Other companies' product names or trademarks are used herein for identification purposes only and belong to their respective companies.
-
Page 3: Safety Instructions
Information for your safety and comfort Safety instructions Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. Special notes on LCD monitors The following are normal with the LCD monitor and do not indicate a problem. •... -
Page 4: Safe Listening
Accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power from the equipment, be sure to unplug the power cord from the electrical outlet. -
Page 5: Product Servicing
ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating. • Do not overload a power outlet, strip or receptacle by plugging in too many devices. -
Page 6: Additional Safety Information
Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition. Potentially explosive environments Switch off your device in any area with a potentially explosive atmosphere and obey all signs and instructions. -
Page 7: Lcd Pixel Statement
LCD pixel statement The LCD unit is produced with high-precision manufacturing techniques. Nevertheless, some pixels may occasionally misfire or appear as black or red dots. This has no effect on the recorded image and does not constitute a malfunction. This product has been shipped enabled for power management: •... -
Page 8: Developing Good Work Habits
viii Taking care of your vision Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly focused screens, very small typefaces and low-contrast displays could stress your eyes. The following sections provide suggestions on how to reduce eyestrain. Eyes •... -
Page 9: Table Of Contents
TABLE OF CONTENTS UNPACKING.................... 1 ATTACHING / REMOVING THE BASE............. 2 SCREEN POSITION ADJUSTMENT ............2 CONNECTING THE POWER CORD............3 SAFETY PRECAUTION................3 CLEANING YOUR MONITOR ..............3 POWER SAVING..................4 DDC......................4 CONNECTOR PIN ASSIGNMENT............. 5 STANDARD TIMING TABLE ..............7 INSTALLATION.................. -
Page 10: Unpacking
UNPACKING Please check the following items are present when you unpack the box, and save the packing materials in case you will need to ship or transport the monitor in future. LCD Monitor AC Power Cord D-Sub Cable DVI Cable (Optional) ... -
Page 11: Attaching / Removing The Base
ATTACHING / REMOVING THE BASE Note: Remove the monitor and monitor base from its packaging. Carefully place the monitor face-down on a stable surface -- use a cloth to avoid scratching the screen. Attach the monitor stand arm to the Ensure that the base is locked onto the base. -
Page 12: Connecting The Power Cord
CONNECTING THE POWER CORD Check first to make sure that the power cord you use is the correct type required for your area. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240 V AC voltage area. No user-adjustment is required. Plug one end of the power cord to the AC Inlet, plug another end to a ... -
Page 13: Power Saving
POWER SAVING The monitor will be driven into Power Saving” mode by the control signal from the display controller, as indicated by the white blinking LED light. State LED Light White Power Saving Mode Blinking The power saving states will be kept until a control signal has been detected or the keyboard or mouse is activated. -
Page 14: Connector Pin Assignment
CONNECTOR PIN ASSIGNMENT 15-Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION Green Logic Ground Blue Monitor Ground Monitor Ground DDC-Serial Data DDC-return H-Sync R-Ground V-Sync G-Ground DDC-Serial Clock B-Ground EN-5... - Page 15 24-Pin Color Display Signal Cable* Meaning Meaning TMDS Data2- TMDS Data2+ +5V Power TMDS Data 2/4 Shield Logic Ground Hot Plug Detect TMDS Data0- DDC Clock TMDS Data0+ DDC Data TMDS Data 0/5 Shield TMDS Data1- TMDS Data1+ TMDS Clock Shield TMDS Data 1/3 Shield TMDS Clock+ DDC TMDS Clock-...
-
Page 16: Standard Timing Table
STANDARD TIMING TABLE Mode Resolution 640 x 480 640 x 480 66.66 VESA 720 x 400 SVGA 800 x 600 SVGA 800 x 600 1024 x 768 1024 x 768 VESA 1152 x 864 SXGA 1280 x 1024 VESA 1280 x 720 WXGA 1280 x 800 WXGA+... -
Page 17: Installation
INSTALLATION To install the monitor to your host system, please follow the steps as given below: Steps 1. 1-1 Connect Video Cable a. Make sure both the monitor and computer are powered-OFF. b. Connect the VGA video cable to the computer. 1-2 Connect Digital Cable (Only Dual-input model) a. -
Page 18: User Controls
USER CONTROLS Base Controls Power Switch / Power LED: To turn the monitor ON or OFF. Lights up to indicate the power is turned ON. / Minus / Plus: If the OSD is active, press the Minus or Plus buttons to toggle between the OSD options. -
Page 19: Ecolor Management
eColor Management Operation instructions Step 1: Press “ ” Key to open the eColor Management OSD and access the scenario modes Step 2: Press ““ or “” to select the mode Step 3: Press “ AUTO “ Key to confirm the mode and run Auto Adjust. Features and Benefits Main Sub Menu... - Page 20 Adjusting the OSD settings Note: The following content is for general reference only. Actual product specifications may vary. The OSD can be used for adjusting the settings of your LCD Monitor. Press the MENU key to open the OSD. You can use the OSD to adjust the picture quality, OSD position and general settings.
- Page 21 Adjusting the OSD position 1 Press the MENU key to bring up the OSD. 2 Using the directional keys, select OSD from the on screen display. Then navigate to the feature you wish to adjust. EN-12...
- Page 22 Adjusting the setting 1 Press the MENU key to bring up the OSD. 2 Using the / keys, select Setting from the OSD. Then navigate to the feature you wish to adjust. 3 The Setting menu can be used to adjust the screen Menu Language and other important settings.
- Page 23 Product information 1 Press the MENU key to bring up the OSD. 2 Using the / keys, select Information from the OSD. Then the basic information of LCD monitor will show up for current input. EN-14...
-
Page 24: Troubleshooting
TROUBLESHOOTING Before sending your LCD monitor for servicing, please check the trouble- shooting list below to see if you can self-diagnose the problem. (VGA Mode) Problems Current Status Remedy Using OSD, adjust brightness and No Picture LED ON contrast to maximum or reset to their default settings. -
Page 25: Dvi Mode
(DVI Mode) Problems Current Status Remedy Using OSD, adjust brightness No Picture LED ON and contrast to maximum or reset to their default settings. Check the power switch. LED OFF Check if AC power cord is properly connected to the monitor. - Page 26 EN-17...
-
Page 27: Energy Star
ENERGY STAR® Acer’s ENERGY STAR qualified products save you money by reducing energy costs and helps protect the environment without sacrificing features or performance. Acer is proud to offer our customers products with the ENERGY STAR mark. What is ENERGY STAR? Products that are ENERGY STAR qualified use less energy and prevent greenhouse gas emissions by meeting strict energy efficiency guidelines set by the U.S.
Need help?
Do you have a question about the Viseo243D and is the answer not in the manual?
Questions and answers