Schlage CO-100 User Manual
Co-series offline locks
Hide thumbs
Also See for CO-100:
- User manual (12 pages) ,
- Installation instructions manual (8 pages) ,
- Installation instructions manual (8 pages)
Related Manuals for Schlage CO-100
Summary of Contents for Schlage CO-100
- Page 1 P516-270 CO-100 OFFLINE LOCK USER GUIDE INSTRUCTIONS FOR CO-SERIES OFFLINE LOCKS Para el idioma español, navegue hacia www.schlage.com/support. Pour la portion française, veuillez consulter le site www.schlage.com/support.
-
Page 2: Table Of Contents
CO-100 Offl ine Lock User Guide CONTENTS Overview ............................3 Getting Started ..........................4 Construction Access Mode ......................4 Manual Lock Programming ......................5 Credential Types ........................5 Programming Legend ........................ 5 Manual Programming Commands ..................... 6 Error Codes ........................... 7 Test Lock Operation ........................ -
Page 3: Overview
CO-100 Offl ine Lock User Guide OVERVIEW The Schlage CO-100 is a keypad-only off-line electronic lock in the CO-Series product line. • This product is listed for UL 294 and ULC S319. • Two factory-confi gured functions are available: 1) Classroom/Storeroom, and 2) Offi ce. -
Page 4: Getting Started
• To test, enter the default PIN (13579 and “ # ”). the lock has already been programmed. • The Schlage button will blink and the lock will unlock. If the new PIN is not known, or to put the lock back into construction access •... -
Page 5: Manual Lock Programming
CO-100 Offl ine Lock User Guide MANUAL LOCK PROGRAMMING Left LED Right LED Credential Types Credential Type Function Description Default PIN Used to program the lock – does not Programming Five-digit code 97531 and unlock the lock Normal Use Unlocks the lock momentarily... -
Page 6: Manual Programming Commands
Schlage button, three left and nine right at the same time. The right LED on the Schlage button will blink green to indicate an incorrect entry. To interpret blink patterns, refer to Error Codes on page 7. -
Page 7: Error Codes
2 Change PIN length is available with fi rmware version 2.5.0 or higher. ERROR CODES All error codes are indicated on the Schlage button by a solid red LED and a blinking green LED. The number of green blinks indicates the error code. -
Page 8: Test Lock Operation
CO-100 Offl ine Lock User Guide TEST LOCK OPERATION If you encounter problems while performing any of the following tests, review the installation guide and correct any problems. Mechanical Test 1. Rotate the inside lever or depress the push bar to open the door. Operation should be smooth, and the latch should retract. -
Page 9: Lock Status Reports
Follow the steps below to obtain lock status reports: Lock status reporting is available with fi rmware version 2.5.0 or higher. The left and right Schlage button LEDs will blink red once with each button press, followed by the status indicator as described below. -
Page 10: Reset To Factory Defaults
3. Press and hold the Schlage button while reconnecting the battery into the battery pack to resupply power. 4. Continue holding the Schlage button, and wait for two beeps to sound and two green blinks of the Schlage button. 5. Release the Schlage button. -
Page 11: Batteries
CO-100 Offl ine Lock User Guide BATTERIES To Install or Replace Alkaline Batteries Changing batteries does not affect any programmed data. 1. Remove the battery cover. 2. Remove the battery bracket. Do not allow the battery pack to hang from the wires. -
Page 12: Led Reference
IPB through-door cable. through-door ribbon Refer to the installation instructions that came with cable may not be the CO-100 lock, or this user guide for details on the properly plugged in, or above mentioned procedures. may have bent pins. FCC STATEMENTS This device complies with Part 15 of the FCC Rules.
Need help?
Do you have a question about the CO-100 and is the answer not in the manual?
Questions and answers