Schlage Connect Quick Start

Schlage
Schlage Connect Smart Deadbolt
SKU: BE469ZP
Quickstart
This is a secure Door Lock - Keypad for U.S. / Canada / Mexico. Please make sure the internal battery is fully charged. To add this device to your
network execute the following action:
One-button Add lock to Z-Wave Network (Inclusion) 1.Place your home automation system or panel into the Add or Inclusion Mode (Refer to the respective
documentation for that specific home automation system or panel device for details). 2.Remove the battery cover of the deadbolt. 3.Press then release the
button on the PCB.4.An LED will flash amber indicating the Add or Inclusion process is in progress. If the Security Scheme is Security 2 (S2), verify the
DSK of the lock at the Z-Wave Controller. The PIN Code portion of the Z-Wave DSK will be needed.5.When a green LED turns ON, the Add or Inclusion
has completed successfully. 6.If a red LED turns ON, try repeating steps 1-3Interactive Instruction for Addhttps://instructions.allegion.com/instr/86/2543
Attention: This manual is automatically generated from
Manual for more information.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and
every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is
not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-
Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this
device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level
of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

The Schlage Connect Smart Deadbolt combines advanced features and compatibility with your home automation or security system, allowing you to control your
lock from anywhere and freeing you from the hassles of lost keys, getting locked out, or hiding a spare for friends and family.The lock comes preprogrammed with
two access codes and can hold up to 30 unique codes for family members and trusted friends. The fingerprint-resistant touchscreen helps access codes stay
private, minimizing tell-tale wear that can tip off possible intruders.The Schlage Connect Smart Deadbolt is battery-powered with a low battery warning that gives
you weeks of advanced notice before it runs out. With guaranteed fit on standard doors, its easy for homeowners to install in minutes with just a screwdriver. The
touchscreen continues to work in the event of a power outage, so you dont have to worry about getting locked outplus, a back-up key is included with the lock for
peace of mind.The Schlage Connect Smart Deadbolt incorporates Z-Wave Plus S2 technology, an enhanced security protocol that features an additional layer of
AES encryption of wireless signals. The Z-Wave technology allows you to integrate your exterior door locks with other Z-Wave smart home devices, such as
cameras, motion detectors, lights and thermostats, bringing the safety, simplicity and style of Schlage to your smart home.

Prepare for Installation / Reset

Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do
this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended
to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Steps for One-button Factory Default Reset 1.Remove the battery cover of the deadbolt2.Press and hold the button on the PCB for 7 (seven) seconds. While
holding the button pressed, after 1 sec LED will be lit for 2 sec. and turn OFF; continue to press and hold the button until the LED will be lit again and release the
button.3.The LED will blink red three times and the green check on the touchscreen will blink if the Factory Default Reset is successful. 4.To check that the lock
was reset, press the Schlage Button and enter one of the Default User Codes. If the reset was successful, the Default User Codes will unlock the deadbolt. NOTE:
Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers