1 Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1-1-1 Warnings (READING SHOULD NOT BE ABOVE 0.5mA) For continued safety, do not attempt to modify the circuit board.
1 Precautions 1-2 Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
2 Product Specifications 2-2 Pin Assignments Sync 15-Pin Signal Cable Connector Type Separate Composite Sync-on-green Pin No. Green Green Green + H/V Sync. Blue Blue Blue GND (DDC Return) GND (DDC Return) GND (DDC Return) GND-Red GND-Red GND-Red GND-Green GND-Green GND-Green GND-Blue GND-Blue...
2 Product Specifications 2-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1 Timing Chart Mode VGA1/ VGA2/ VGA3/ VGA/ VGA/ MAC/ MAC/ SVGA/ SVGA/ SVGA/ 70 Hz 70 Hz...
Page 9
2 Product Specifications Table 2-1 Timing Chart (continued) Mode NCD/70 Hz SXGA/75 Hz SUN/66 Hz SUN/76 Hz SXGA/60 Hz HP/72 Hz SUN/76 Hz 1280 x 1024 1280 x 1024 1152 x 900 1152 x 900 1280 x 1024 1280 x 1024 1280 x 1024 Timing fH (kHz)
Page 10
2 Product Specifications Table 2-1 Timing Chart (continued) Mode Analog UXGA/60Hz 1600 x 1200 Timing fH (kHz) A µsec 2160 B µsec C µsec D µsec 1600 E µsec fV (Hz) O msec 1250 P msec Q msec R msec 1200 S msec Clock...
3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the 213T monitor. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1 Disassembly Cautions : 1. Disconnect the monitor from the power source before disassembly. 2.
Page 12
3 Disassembly and Reassembly 6. Disconnect LVDS cable from the panel and disconnect invertor cable from the shield. 7. Disconnect function cable from the shield and lift up the panel. 8. Remove 4 screws from the panel. (right and left) 3-2 Replacement Order of Lamp Assemblies 1.
Page 13
3 Disassembly and Reassembly 2. Unscrewing the screw. Unscrewing force : 0.8 ~ 1Kg - f.cm 3. Pulling out the lamp assembly with stable power and direction slowly. Be careful, do not twist the lamp reflector when pulling the lamp. 4.
Page 14
3 Disassembly and Reassembly 3-3 Reassembly Reassembly procedures are in the reverse order of disassembly procedures. 213T...
4 Alignments and Adjustments This section of the service manual explains how to use the DDC JIG to adjust the black, red, green, and blue levels of the FPD when you replace the AD board, and how to update the microprocessor when you change the panel or lamp(s).
5 Troubleshooting 5-1 No Power Does proper 14 V appear at Check SMPS. Pin 1, 2 and 3 of CN101? Does proper 5 V appear at Check SMPS, Q101 and IC104. Pin 5, 6, 7 and 8 of IC104? Does proper 3.3 V appear at Check IC101, IC105 and IC106.
Page 18
5 Troubleshooting 5-2 No Video (PC Analog Signal) Power indicator is green Does the signal appear at Pin 5, Check BD201~BD203, 13 and 20 of IC201? R214, R217 and R224. Does the clock pulse appear at Check IC201 and related circuit of IC301. Pin 1, 2, 3 of IC201? Does the sync signal Check Pin 44, 45 of IC204 and IC201.
Page 19
6 Exploded View and Parts List You can search for updated part codes through CMS web site. URL : http://ecms. samsungelectronics. com/ REMARK 213T...
7 Electrical Parts List ❈ You can search for updated part codes through CMS web site. URL : http://ecms. samsungelectronics. com/ 7-1 Main PCB Parts Loc. No. Code No. Description Specification Remarks BN94-00454A ASSY PCB MAIN-E5 NB21BS CIS02 0202-001044 SOLDER-WIRE. S63S-W3.0,S63S,D3,63Sn/37Pb,- CIS03 6011-001445...
Need help?
Do you have a question about the Syncmaster 213T and is the answer not in the manual?
Questions and answers