Page 4
Contents . Wiring Diagram …………………………………………………………………………………………………………………………………8 9. S chematic Diagrams ……………………………………………………………………………………………………………………………9 9-1 Schematic Diagrams ……………………………………………………………………………………………………………………… 9-1 9-2 Schematic Diagrams ………………………………………………………………………………………………………………………9-3 1 1 0. Operating Instructions and Installation … … …………………………………………………………………………………………………10-1 10-1 Front …………………………………………………………………………………………………………………………………… 10-1 10-2 Rear ………………………………………………………………………………………………………………………………………10-2 10-3 Using the Stand …………………………………………………………………………………………………………………………10-4 1 1 1.
Page 5
Samsung Electronics Co.,Ltd. -This Service Manual is a property of Samsung 416, Maetan-3Dong, Yeongtong-Gu, Suwon City, Electronics Co., Ltd. Gyeonggi-Do, Korea, 443-742 Any unauthorized use of Manual can be punished Printed in Korea under applicable International and/or domestic P/N : BN82-00138M-00 law.
11 Disassembly and Reassembly 11 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the LHA20WS TFT-LCD monitors. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 11-1 Disassembly Cautions: 1.
Page 7
11 Disassembly and Reassembly Description Picture Description 4. Use the jig to remove the shield lamp. (Be careful Shield.) 5. Remove the FUNCTION Wire from PCB ASS’ Y. 6. Remove the Panel Lamp wire. 7. Remove the LVDS Wire from Panel. 8.
14 Reference Infomation 14 Reference Infomation 14-1 Technical Terms - TFT-LCD - FINE "Fine" adjustment is used to adjust visibility by (Thin film Transistor Liquid Crystal Display) ADC(Analog to Digital Converter) control phase difference. This is a circuit that converts from analog signal to digital signals.
Page 15
14 Reference Infomation - Dot Pitch - External Device Input The image on a monitor is composed of red, green External device input refers to video input from and blue dots. The closer the dots, the higher the such external video devices as VCRs, camcorders resolution.
14 Reference Infomation - Connecting the Monitor Connect the DC adapter for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
14 Reference Infomation 14-2 Pin Assignments Sync 15-Pin D-Sub Signal Cable Connector Type Separate Composite Sync-on-green Pin No. Green Green Green + H/V Sync. Blue Blue Blue DDC Return (GND) DDC Return (GND) DDC Return (GND) GND-R GND-R GND-R GND-G GND-G GND-G GND-B...
14 Reference Infomation 14-3 Timing Chart - This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 14-1 Timing Chart VESA Mode VGA2/ VGA3/ 640/75 Hz 800/60 Hz 800/75 Hz 1024/60 Hz 1024/75 Hz 1280/60 Hz...
14 Reference Infomation 14-4 Preset Timing Modes - If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on.
-. Embeded Power, Mechanical S/W application 2-2 Feature Feature Feature Operating method If 206BW/226BW turns on in some resolution for the first time, it can Auto Auto execute Auto adjustment automatically for the high Quality Auto Power 206BW/226BW can check the change of Source...
3 Alignments and Adjustments 3 Alignments and Adjustments This section of the service manual explains how to use the RS232 JIG. This function is needed for AD board change. 3-1 Required Equipment The following equipment is necessary for adjusting the monitor: - Computer with Windows 95, Windows 98, Windows 2000, Windows XP or Windows NT.
3 Alignments and Adjustments 3-4 Service Function Spec. 3-4-1 How to Display Service Function OSD 1. After setting both brightness and contrast to '0' push the 'enter' button more than 5 seconds. 2. service function appear as below. Figure 2. 3-4-2 How to Control Service Function OSD 1.
3 Alignments and Adjustments 3-5 Hidden Key list Function Action method Hidden Service Function -. After setting brightness and contrast '0' push the "Menu" button more than 5 seconds. -. Service Function appear. Factory Reset -. While Menu is opened(any menu), press "enter" key over 5 seconds.
3 Alignments and Adjustments 3-6 DDC Input Method(Windows Program) After change a Main Board ,DDC input shpuld be done via DDC control JIG. Connecting method is refer to below picture. 1. Winddc.exe Program install in PC 2. Cilck the Winddc icon. 3.
3 Alignments and Adjustments 5: Input a monitor serial number and push the enter key. After Analog input, Please do # 2 ~ 5 when digital input. 3-7 Execution Items after replacing the main board After Replacing the Maing Board 1.
Page 36
10 Operating Instructions and Installation 10 Operating Instructions and Installation 10-1 Front 1. Menu button 3) Internet Opens the OSD menu. Also use to exit the OSD For working with a mixture of images such as text menu or return to the previous menu. and graphics.
Page 37
10 Operating Instructions and Installation 2,3. Adjust buttons 5. Auto button Adjust items in the menu. When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the ani- 4. Enter button / Source button mated screen on the center. Auto adjustment Activates a highlighted menu item.
Page 38
10 Operating Instructions and Installation 10-3 Using the Stand 10-3-1 Removing the base 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3.
Page 39
10 Operating Instructions and Installation 10-3-2 Attaching a Base - This monitor accepts a 100mm x 100mm VESA-compliant mounting interface pad. A. Monitor B. Mounting interface pad 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3.
4 Troubleshooting 4 Troubleshooting 4-1 No Power There is no light in the power indicator. Does proper DC 14 V appear at Pin 5,6,7,9 Check the IP Board. of CN700? Does proper DC 5V Check the IC702 appear at Output of C719? Does proper DC 3.3V Check the IC705.
4 Troubleshooting 4-2 No Video (PC Analog Signal) Is pin9 of Check TFT_LCD panel or inverter CN700(BKLT_EN)high(3.3V)? and connection between then. Does the analog video signal Check pc signal. appear at R104, R105, R106 (Red,Green,Blue)? Does the X710 Check the X300. oscilate Properly? Replace LCD Panel.
4 Troubleshooting 4-3 No Video (PC Digital Signal) Check TFT_LCD panel or inverter Is Pin9 of and connection between then. CN700(BKLT_EN)high(3.3V)? Does the Digital video Check PC signal. signal appear at R200 ~ R227? Replace LCD Panel.
5 Exploded View & Parts List 5 Exploded View and Parts List -You can search for updated part codes through ITSELF web site. URL : http://itself. sec. samsung.co.kr 5-1 LHA20WS Exploded View M0215 T0003 M0006 M0014 M0112 M0174 M0013 T0056...
6 Electrical Parts List 6 Electrical Parts List -You can search for updated part codes through ITSELF web site. URL : http://itself.sec.samsung.co.kr/ 6-1 LME20WS Parts List Level Loc. No. Code No. Description & Specification Q'ty SA/SNA LS20MEWSFV/XAA 206BW,WSE1/S20A1-LME,20,LCD-MO,UNITED ST M0216 BN90-01037B ASSY STAND;LS20MEW...
Page 70
8 Wiring Diagram 8 Wiring Diagram Connected to the I/P board Connected to the Panel through the LVDS cable For test(not used) For DVI signal For function key For Analog signal...
Contents . Wiring Diagram …………………………………………………………………………………………………………………………………8 9. S chematic Diagrams ……………………………………………………………………………………………………………………………9 9-1 Schematic Diagrams ……………………………………………………………………………………………………………………… 9-1 9-2 Schematic Diagrams ………………………………………………………………………………………………………………………9-3 1 1 0. Operating Instructions and Installation … … …………………………………………………………………………………………………10-1 10-1 Front …………………………………………………………………………………………………………………………………… 10-1 10-2 Rear ………………………………………………………………………………………………………………………………………10-2 10-3 Using the Stand …………………………………………………………………………………………………………………………10-4 1 1 1.
Page 76
Samsung Electronics Co.,Ltd. -This Service Manual is a property of Samsung 416, Maetan-3Dong, Yeongtong-Gu, Suwon City, Electronics Co., Ltd. Gyeonggi-Do, Korea, 443-742 Any unauthorized use of Manual can be punished Printed in Korea under applicable International and/or domestic P/N : BN82-00138M-00 law.
Page 77
9 Schematic Diagrams 9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-1 Schematic Diagrams...
Page 78
9 Schematic Diagrams - This Document can not be used without Samsung s authorization.
Page 79
9 Schematic Diagrams - This Document can not be used without Samsung s authorization.
Need help?
Do you have a question about the 226BW and is the answer not in the manual?
Questions and answers