Huawei SmartAX MT800 User Manual
  1. Manuals
  2. Brands
  3. Huawei Manuals
  4. Network Router
  5. SmartAX MT800
  6. User manual
Huawei SmartAX MT800 User Manual

Huawei SmartAX MT800 User Manual

Adsl
Hide thumbs Also See for SmartAX MT800:
Table of Contents

Advertisement

Quick Links

Download this manual
SmartAX MT800 ADSL Router
User Manual

Advertisement

Table of Contents
loading

Related Manuals for Huawei SmartAX MT800

Summary of Contents for Huawei SmartAX MT800

  • Page 1 SmartAX MT800 ADSL Router User Manual...
  • Page 2 HUAWEI SmartAX MT800 ADSL Router User Manual V100R006...
  • Page 3 Please feel free to contact our local office or company headquarters. Huawei Technologies Co., Ltd. Address: Administration Building, Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, P. R. China Postal Code: 518129 Website: http://www.huawei.com...
  • Page 4 Copyright © 2004 Huawei Technologies Co., Ltd. All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks , HUAWEI, C&C08, EAST8000, HONET,...

  • Page 5: About This Manual

    About This Manual Release Notes The product version corresponds to the manual is SmartAX MT800 ADSL Router V100R006C01B020SP01. Organization 1 MT800 Overview provides a brief description of MT800 and a list of features. 2 Hardware Installation introduces the hardware installation of MT800.

  • Page 6: Intended Audience

    Intended Audience The manual is intended for the following readers: Marketing staff Installation engineers & technicians Operation & maintenance personnel Conventions The manual uses the following conventions: I. General conventions Convention Description Arial Normal paragraphs are in Arial. Warnings, Cautions, Notes and Tips are in Arial Arial Narrow Narrow.

  • Page 7: Environmental Protection

    Caution: Means reader be extremely careful during the operation. : Means a complementary description. Environmental Protection This product has been designed to comply with the requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be observed.

  • Page 8: Table Of Contents

    Table of Contents Chapter 1 MT800 Overview .............. 1 1.1 Appearance................1 1.2 Parts of MT800..............1 1.2.1 Front Panel ..............1 1.2.2 Rear Panel..............2 1.2.3 External Splitter ............3 1.3 MT800 Features..............4 Chapter 2 Hardware Installation............5 2.1 Preparations................
  • Page 9 4.2 System View (Home Page) ..........15 4.3 ATM Setting ................ 16 4.3.1 RFC2684 Bridged Connection ......... 16 4.3.2 RFC2684 Route (IPoA) Configuration...... 23 4.3.3 PPP Configuration ............ 24 4.4 ADSL Mode Configuration ..........30 4.5 LAN Configuration............... 31 4.6 DHCP Mode Configuration ..........33 4.7 DNS Configuration ..............
  • Page 10 4.20 Firmware Upgrade ............77 4.21 Alarm ................. 78 Chapter 5 Service Configuration........... 79 5.1 Preparation for Service Configuration......... 79 5.2 PPPoE Configuration ............80 5.3 PPPoA Configuration ............82 5.4 RFC 2684 Bridged (Pure Bridge) Configuration ....83 5.5 RFC 2684 Bridged (Static IP) Configuration ....... 83 5.6 RFC 2684 Bridged (DHCP) Configuration ......

  • Page 11: Chapter 1 Mt800 Overview

    Chapter 1 MT800 Overview In this chapter you will learn about the appearance and features of MT800. 1.1 Appearance MT800 provides the small and private network with simple, secure, and cost-efficient ADSL Internet connection. It enables many interactive multi-media applications. MT800 has considered the household arrangements, enabling horizontal and vertical positions as well as hanging on the wall.

  • Page 12: Rear Panel

    Figure 1-2 Front panel display with LED Indicators The meaning of LEDs are listed as follows: Status Description Indicator Power Steady green light The unit is powered on. ADSL LINK Steady green light A valid ADSL connection. ADSL ACT Blinking green light There is traffic over ADSL line.

  • Page 13: External Splitter

    Figure 1-3 Rear panel cable and power connections ADSL: ADSL port, connecting to the splitter. Ethernet: Ethernet port, connecting to PC or hub. Reset: Press this button for 3 seconds to restore the default setting. This operation will let you lose your custom setting.

  • Page 14: Mt800 Features

    MODEM: Connecting to ADSL modem with RJ-11 telephone line. 1.3 MT800 Features Data rates up to 8 Mbps for downstream and 896 kbps for upstream. Friendly Web-based graphical user interface configuration and management. Supporting up to eight simultaneous virtual connections. Various LED indicators facilitating the troubleshooting and maintenance of the device.

  • Page 15: Chapter 2 Hardware Installation

    Chapter 2 Hardware Installation In this chapter you will learn about the various connections you need to make in order to use the MT800. Preparations Connecting MT800 Power on MT800 2.1 Preparations 2.1.1 Checking Computer Configuration Item Requirement Web browser, such as IE, is installed. Microsoft Internet Explorer 5.0 or Netscape Navigator ®...

  • Page 16: Connecting Mt800

    User name, password 2.2 Connecting MT800 2.2.1 Connecting ADSL Line Simply plug one end of the twisted-pair telephone cable into the Modem port of the splitter and insert the other end into the ADSL port on the rear panel of MT800. Use another telephone cable to connect the splitter and the Phone Jack in the wall.

  • Page 17: Connecting Ethernet Lan To Mt800

    (1) Computer (2) RJ-11 Tel Cable (3) Phone (4) RJ-45 Ethernet Cable (5) Splitter (6) Phone Jack (7) MT800 (8) RJ-11 Tel Cable Figure 2-1 Computer to MT800 connection 2.2.3 Connecting Ethernet LAN to MT800 MT800 may be connected to any 10/100Base-TX Ethernet port. When connecting MT800 to any Ethernet device that is capable of operating at speeds higher than 10Mbps, be sure that the device has auto-negotiation mode enabled for the connecting port.

  • Page 18: Powering On Mt800

    2.3 Powering On MT800 Use the provided power adapter and plug it into a suitable power source nearby. You should see the Power LED indicator light up, which indicates the device is powered on. After a few seconds, look at the LAN LINK indicator and make sure it with steady light, which indicates a valid connection between the router and your computer.

  • Page 19: Chapter 3 Before Configuring Mt800

    Chapter 3 Before Configuring MT800 To configure MT800, you have to connect MT800 to a computer as shown below. Use the provided straight-through cable. (1)Computer (2)RJ-45 Ethernet Cable (3)MT800 Figure 3-1 Computer to MT800 connection 3.2 When to Configure the MT800 The factory default settings of MT800 have optimized all functions, which made it can operate in most conditions of network.

  • Page 20: Configuring Ip Settings On Your Computer

    If the conditions of network have been changed by the modification of security, scale, line of communication, protocol and topology, for example, a demand of particular VPI and VCI, you should adjust accordingly the default settings to be able to adapt to the changes.

  • Page 21: Checking For Proxy Service

    3.4.1 Checking for Proxy Service If the browser software on the computer is configured to use a proxy server for Internet access, it is necessary to first disable the proxy connection. In Windows Internet Explorer, you can check whether a proxy server is enabled using the following procedures: Explorer Window,...
  • Page 22 Figure 3-2 Enter user name and password Use the default user name: admin and password: admin for first time setup. You can change the password once you have opened the Web-based configuration manager. The user name and password allows any computer on the same subnet as the MT800 to access the Web-based configuration manger.

  • Page 23: Chapter 4 Web-Based Management

    Chapter 4 Web-based Management This chapter describes how to use the web-based management software to configure the MT800, which introduces the signification of parameters and method of setting in the configuration interface. The order of sectors is listed according to the functional configuration interfaces.
  • Page 24 Figure 4-1 GUI of web-based configuration manager...

  • Page 25: System View (Home Page)

    4.2 System View (Home Page) Figure 4-2 Home Page – system view display...

  • Page 26: Atm Setting

    The System View read-only table on the Home Page displays a summary of various system settings and functions as described in the table below. Device: Displaying the basic information about the device model and software versions. DSL Status: Displaying the operational status, DSL version, and performance statistics for the DSL line.
  • Page 27 PVC: System provides 8 PVCs. Generally you can leave this set at the default value 0. This option is also used to create and configure new PVCs. VPI: If you need any modification, please enter the VPI value provided by ISP. See the attached table for all the VPI default value of PVC.
  • Page 28 Figure 4-3 RFC2684 bridged connection-application of pure bridge The RFC2684 bridged connection-application of pure bridge mode displays a summary of various system settings and functions as described below: PVC: System provides 8 PVCs. Generally you can leave this set at the default value 0. This option is also used to create and configure new PVCs.
  • Page 29 VCI: If you need any modification, please enter the VCI value provided by ISP. See the attached table for all the VCI default value of PVC. Operation Mode: This also should be left at the default setting Enabled. This enables the PVC used for the initial connection.
  • Page 30 Figure 4-4 RFC2684 bridged connection-application of static IP IP Address and Subnet Mask: Entered IP address and subnet mask provided by ISP for the WAN interface of your MT800. Default Route: This setting specified the IP address below is used for default route of LAN. The data will be sent through WAN interface whenever a client LAN computer accesses the Internet.
  • Page 31 Configured MTU: Enter the maximum bytes of the packet being transmitted during connection. III. DHCP The setting page displayed as below will appear if you select DHCP mode, which means automatically acquire IP address from the DHCP sever of ISP. Figure 4-5 RFC2684 Bridged Connection-application of DHCP Default Route: This setting specified the IP address below is used for default route of LAN.
  • Page 32 through WAN interface whenever a client LAN computer accesses the Internet. Gateway IP address: Enter the Gateway address provided by ISP. Traffic Index: Select the index number for ATM traffic from the pull-down menu. Configured MTU: Enter the maximum bytes of the packet being transmitted during connection.

  • Page 33: Rfc2684 Route (Ipoa) Configuration

    4.3.2 RFC2684 Route (IPoA) Configuration Configuration page Figure 4-6 RFC2684 route (IPoA) configuration Parameters explanation PVC: The system provides 8 PVCs. Generally you can leave this set at the default value 0. This option is also used to create and configure new PVCs. VPI: If you need any modification, please enter the VPI value provided by ISP.

  • Page 34: Ppp Configuration

    VCI: If you need any modification, please enter the VCI value provided by ISP. See the attached table for all the VCI default values of PVCs. Operation Mode: This also should be left at the default setting Enabled. This enables the PVC used for the initial connection.
  • Page 35 PPPoA Figure 4-7 PPP configuration-PPPoA PVC: System provides 8 PVCs. Generally you can leave this set at the default value 0. This option is also used to create and configure new PVCs. VPI: If you need any modification, please enter the VPI value provided by ISP.
  • Page 36 VCI: If you need any modification, please enter the VCI value provided by ISP. See the attached table for all the VCI default value of PVC. Operation Mode: This also should be left at the default setting Enabled. This enables the PVC used for the initial connection.
  • Page 37 PPPoE Figure 4-8 PPP configuration-PPPoE PVC: The system provides 8 PVCs. Generally you can leave this set at the default value 0. This option is also used to create and configure new PVCs. VPI: If you need any modification, please enter the VPI value provided by ISP.
  • Page 38 VCI: If you need any modification, please enter the VCI value provided by ISP. See the attached table for all the VCI default value of PVC. Operation Mode: This also should be left at the default setting Enabled. This enables the PVC used for the initial connection.
  • Page 39 III. PPP Interface After modification, click on Submit button, a Status entry will be added to the configuration page. Please click on icon to reveal PPP Interface page. The PPP interface is shown in Fig. 4-9 below. Figure 4-9 PPP Interface WAN IP Address Displays the IP address of WAN port on PPP interface.

  • Page 40: Adsl Mode Configuration

    Connect If it is selected, MT800 will automatically enable the PPP dial connection each time the device is powered on. Auto Connect If it is selected, MT800 will automatically redial after timing out and the disconnection is executed. Manual If it is selected, you need to establish the PPP dial connection manually by clicking on Connect button.

  • Page 41: Lan Configuration

    Configuration page Figure 4-10 ADSL mode configuration Save Click the Submit button to save the settings in the RAM. To save these configuration changes permanently, enter the Save & Reboot page, select Save and click Submit button to save new settings. 4.5 LAN Configuration Click the LAN Configuration of Other Setting in the Wizard Column to set the LAN interface.
  • Page 42 Configuration page Figure 4-11 LAN configuration Parameter explanation To change the LAN IP address, click the Refresh button and type in the new settings as described below. LAN IP Address: Type in the IP address for the Ethernet LAN interface. The default IP address is 192.168.1.1 LAN Network Mask: Type in the Subnet Mask for the Ethernet LAN IP interface.

  • Page 43: Dhcp Mode Configuration

    III. Save Click the Submit button to save the settings in the RAM. To save these configuration changes permanently, enter the Save & Reboot page, select Save and click Submit button to save new settings. Note: If you change the IP address, you need login in again. 4.6 DHCP Mode Configuration Click the DHCP Mode of Other Setting in the Wizard Column to set the DHCP mode.
  • Page 44 DHCP Server MT800 can be configured as DHCP server of LAN. Then the ADSL terminal shall provide IP settings for your PC. Figure 4-13 DHCP mode configuration-DHCP Server Start/End IP Address: The range of IP addresses that release by DHCP server. Gateway Address: The IP address of gateway for DHCP server.

  • Page 45: Dns Configuration

    Figure 4-14 DHCP mode configuration-DHCP Relay DHCP Server Address: Input the assigned address in the field. Interfaces Running DHCP Relay: Please select the eth value from pull-down menu, and click Add button as well. Action(s): Click icon to delete an added DHCP relay. Save Click the Submit button to save the settings in the RAM.
  • Page 46 typically provide primary and secondary DNS addresses, and may provide additional addresses. Configuration page Figure 4-15 DNS configuration Save Click the Submit button to save the settings in the RAM. To save these configuration changes permanently, enter the Save & Reboot page, select Save and click Submit button to save new settings.

  • Page 47: Ip Route Table Configuration

    4.8 IP Route Table Configuration Click the IP Route of Other Setting in the Wizard Column to set the IP Route Table. IP Routes are used to define gateways and hops used to route data traffic. Most users will not need to use this feature as the previously configured default gateway and LAN IP settings on your host computers should be sufficient.
  • Page 48 used for all destinations for which no other routes are defined (this is the route that creates the default gateway). Netmask: Indicating which parts of the destination address refer to the network and which parts refer to a computer on the network.

  • Page 49: Nat Configuration

    4.9 NAT Configuration Network Address Translation (NAT) is a method for disguising the private IP addresses on your LAN as the public IP address on the Internet. You define NAT rules that specify exactly how and when to translate between public and private IP addresses. Click the NAT of Other Setting in the Wizard Column to set the NAT.
  • Page 50 Figure 4-18 Add NAPT rule Figure 4-19 Add DMZ rule...
  • Page 51 Figure 4-20 Add REDIRECT rule Parameter explanation The explanation of parameters in the above windows is as below. NAT Configuration: Rule ID: The Rule ID determines the order in which rules are invoked (the lowest numbered rule is invoked first, and so on).
  • Page 52 Protocol: This selection specifies which type of Internet communication will be subject to this translation rule. You can select TCP or UDP. Local IP From: Type the starting IP of the range of private address you want to be translated. You can specify that data from all LAN addresses should be translated by typing 0 (zero) in each From field and 255 in each To field.

  • Page 53: Atm Traffic

    Destination Port From: Enter the starting port ID (or a range) that you expect to see on incoming packets destined for the LAN computer for which this rule is being created. With the ending port ID (or a range) specified in the next field, incoming traffic that meets these criteria will be redirected to the Local Port number you specified.

  • Page 54: Rip Configuration

    Parameters explanation Traffic Id: The ID number of ATM traffic. Type: The traffic type of created ATM. Service Category: The service category of created ATM. Creator: The creator’s name. Action(s): Click icon to delete an existed ATM from table; Click icon to view the parameters of an existed DHCP server.
  • Page 55 Configuration page Figure 4-22 RIP configuration Change RIP configuration: If necessary, change the Age and Update Time. These are global settings for all interfaces that use RIP. Age is the amount of time in seconds that the device's RIP table will retain each route that it learns from adjacent computers.
  • Page 56 alternative routes, the one with the lowest hop count is considered the fastest path. Select Send Mode and Receive Mode. The Send Mode setting indicates the RIP version this interface will use when it sends its route information to other devices. The Receive Mode setting indicates the RIP version(s) in which information must be passed to the MT800 in order for it to be accepted into its routing table.

  • Page 57: Firewall Configuration

    4.12 Firewall Configuration 4.12.1 Configuration of Global Firewall The Firewall enables you to protect the system against denial of service (DoS) attacks and other types of malicious accesses to your LAN. You can also specify how to monitor attempted attacks, and who should be automatically notified.
  • Page 58 Parameter explanation Follow these instructions to configure global firewall settings. Configure any of the following settings that display in the Firewall Global Configuration table: Blacklist Status: If you want the device to maintain and use a black list, click Enable. Click Disable if you do not want to maintain a list.

  • Page 59: Managing The Blacklist

    Max Half open TCP Connection: Set the percentage of concurrent IP sessions that can be in the half-open state. In ordinary TCP communication, packets are in the half-open state only briefly as a connection is being initiated; the state changes to active when packets are being exchanged, or closed when the exchange is complete.

  • Page 60: Ip Filter Configuration

    time that you specify. You can enable or disable use of the black list using the settings described above. To view the list of currently blacklisted computers, click the Black List button at the bottom of the Firewall Configuration page. The table displays the following information for each entry.
  • Page 61 Configuration page Figure 4-24 IP filter configuration Parameter explanation Security Level: This setting determines which IP Filter rules take effect, based on the security level specified in each rule. For example, when High is selected, only those rules that are assigned a security value of High will be in effect.

  • Page 62: Adding An Ip Filter Rule

    interfaces is Accept, so that all accesses to your LAN initiated from external computers are denied (discarded at the public interface), except for those allowed by a specific IP Filter rule. A private interface connects to your LAN, such as the Ethernet interface.
  • Page 63 Configuration page Figure 4-25 Add IP filter rule...
  • Page 64 Parameter explanation Rule ID: Each rule must be assigned a sequential ID number. Rules are processed from lowest to highest on each data packet, until a match is found. It is recommended that you assign rule IDs in multiples of 5 or 10 (e.g., 10, 20, 30) so that you leave enough room between them for inserting a new rule if necessary.
  • Page 65 occurring in the previous x minutes. (Logging may be helpful when troubleshooting.) This information can also be e-mailed to administrators. Security Level: The security level that must be enabled globally for this rule to take affect. A rule will be active only if its security level is the same as the globally configured setting (shown on the main IP Filter page).
  • Page 66 gt: any source IP address that is numerically greater than the specified address. gteq: any source IP address that is numerically greater than or equal to the specified address. eq: any source IP address that is numerically equal to the specified address. neq: any source IP address that is not equal to the specified address.
  • Page 67 number, from 0-255, as defined by the Internet Assigned Numbers Authority (IANA). Apply Inspection: If this option is enabled, then Stateful Filtering is performed and the rule is also applied in the other direction on the given interface during an IP session. Source Port: Port number criterion for the computer(s) from which the packet originates.
  • Page 68 specify that the value must equal (eq) or not equal (neq) the specified value, or you can select any to enable the rule to be invoked on all ICMP packets. This field will be dimmed (unavailable for entry) unless you specify ICMP as the protocol.

  • Page 69: Qos

    When you are done selecting criteria, ensure that the Enable button is selected at the top of the page, and then click the Submit button at the bottom of the page. After a confirmation page displays, the IP Filter -Configuration page will redisplay with the new rule showing in the table.
  • Page 70 No QoS Figure 4-26 QoS-No QoS Application Some special application, such network game, videoconference, network phone, will transmit the audio, video and data synchronously. So you can set the priority level to the different type of traffic. So the traffic with higher priority will be processed firstly while the network jammed.
  • Page 71 Priority Queue Index: Provided 4 priority queues. MT800 will set the received traffic into one of 4 priority queues for output. The packet with highest priority will be outputted firstly. If this queue is empty, the next packet with highest priority will be outputted, the rest may be deduced by analogy.
  • Page 72 Figure 4-28 QoS-TOS Priority Queue Index: Provided 4 priority queues. MT800 will set the received traffic into one of 4 priority queues for output. The packet with highest priority will be outputted firstly. If this queue is empty, the next packet with highest priority will be outputted, the rest may be deduced by analogy.
  • Page 73 Figure 4-29 QoS-DiffServ Priority Queue Index: Provided 4 priority queues. MT800 will set the received traffic into one of 4 priority queues for output. The packet with highest priority will be outputted firstly. If this queue is empty, the next packet with highest priority will be outputted, the rest may be deduced by analogy.
  • Page 74 Figure 4-30 QoS-802.1p Priority Queue Index: Provided 4 priority queues. MT800 will set the received traffic into one of 4 priority queues for output. The packet with highest priority will be outputted firstly. If this queue is empty, the next packet with highest priority will be outputted, the rest may be deduced by analogy.
  • Page 75 Figure 4-31 QoS-VLAN Tag Priority Queue Index: Provided 4 priority queues. MT800 will set the received traffic into one of 4 priority queues for output. The packet with highest priority will be outputted firstly. If this queue is empty, the next packet with highest priority will be outputted, the rest may be deduced by analogy.

  • Page 76: Blocked Protocols

    4.15 Blocked Protocols Click the Blocked Protocols of Advanced Function in the Wizard Column to set the Blocked Protocols. The MT800 is capable of sending and receiving information in a variety of protocol formats. The Blocked Protocols feature enables you to prevent the MT800 from passing any data that uses a particular protocol.

  • Page 77: Diagnostics

    Save Click the Submit button to save the settings in the RAM. To save these configuration changes permanently, enter the Save & Reboot page, select Save and click Submit button to save new settings. 4.16 Diagnostics The diagnostics feature executes a series of test of your system software and hardware connections.

  • Page 78: Access Management

    Select the Virtual Circuit and click the Submit button. A message will appear, informing you whether the loop test succeeded or failed. The diagnostics utility will run a series of test to check whether the device's connections are up and working. This takes only a few seconds.
  • Page 79 Figure 4-35 User Config-Modify Perform the following steps to change the password: Open the Access Management page; Enter the configuration page User Config-Modify by click in the operation column; Enter the new password, confirm the password and submit. Save the setting in the Save & Reboot page and then restart the system to take effect the setting.
  • Page 80 Add new user To add new user ID and password, click the Add Button in Access Management page, log into the User Configuration-Add page. Figure 4-36 User config - add User ID: This lists the current User ID (user name). Privilege: Root –...

  • Page 81: Web Management

    4.17.2 Web Management Please input the value of Inactivity TimeOut duration in minutes. If the idle time of web-based management exceeds the input time, the web management will be closed. To access the web management page, you should login again. Figure 4-37 Web management Enter a value of inactivity timeout in the blank and then click Submit button.

  • Page 82: Acl

    Figure 4-38 Ilmi Ilmi: Select to enable or disable the Ilmi mode. VPI: If you need any modification, please enter the VPI value of Ilmi that provided by ISP. VCI: If you need any modification, please enter the VCI value of Ilmi that provided by ISP. 4.17.4 ACL Access Control List is used to allow or deny the access from one or more specific IP addresses in LAN and WAN.
  • Page 83 Configuration page Figure 4-39 Access control list Parameter explanation ACL: Select to allow or deny the access LAN interface or WAN interface. Add IP Address (max 5): Type in the IP address for the LAN interface or WAN interface. The maximum number of IP address can be entered is 5.

  • Page 84: Statistics

    To save these configuration changes permanently, enter the Save & Reboot page, select Save and click Submit button to save new settings. 4.18 Statistics MT800 provides the statistic figures for DSL and ATM/LAN. 4.18.1 DSL Click the DSL of Statistics in the Wizard Column to view the log of device.

  • Page 85: Atm/Lan

    Choose from the pull-down menu to set the refresh rate in seconds. The larger the value is, the slower the refresh rate is. 4.18.2 ATM/LAN The device keeps statistic of the data traffic that it handles. You are able to read the amount of Receive and Transmit packets that pass through the device on both the ATM port and the LAN (Local Area Network) ports.

  • Page 86: Save & Reboot

    4.19 Save & Reboot Click the Save & Reboot in Wizard column to specify the method of restart. Configuration page Figure 4-42 Save & Reboot Parameter explanation Save: Save the current setting into the permanent storage Reboot: A simple reboot: This will put into effect any configuration changes that have been successfully saved to flash memory.

  • Page 87: Firmware Upgrade

    Caution: Do not reboot the device using the Reset button on the back panel of the MT800 to activate new changes. This button resets the device settings to the manufacturer’s default values. Any custom settings will be lost. 4.20 Firmware Upgrade Click the hyperlink Firmware Upgrade in the Wizard column to open the Firmware Upgrade page and update the system software.

  • Page 88: Alarm

    Caution: Do not power off the MT800 during the firmware upgrade process. Otherwise, the configuration in the flash could be damaged. 4.21 Alarm Figure 4-44 Alarm You can view the logs of alarm in response to system events. Select Refresh rate from the drop-down menu. Click the Save Alarm button to save the log file to local disk.

  • Page 89: Chapter 5 Service Configuration

    Chapter 5 Service Configuration This section describes the configuration for six modes of SmartAX MT800 ADSL router device for ADSL online service. The contents include: Preparation for service configuration PPPoE PPPoA RFC 2684 Bridged (Pure Bridge) RFC 2684 Bridged (Static IP)

  • Page 90: Pppoe Configuration

    Virtual dialup DSL mode mode Protocol 2648 2684 types 2684 2684 Bridged Bridged PPPoE PPPoA Bridged Route (Pure (Static (DHCP) (IPoA) Bridge) Connec Connec Connec Connecti Connecti Connecti tion tion tion on Type on Type on Type Type Type Type PPPoE PPPoA user...
  • Page 91 Configurations on MT800 Location Parameters Comments Operation Mode Select “Enable”. The value shall be provided by your ISP. Usually you can keep the default value: Encapsulation LLC. Connection Type Select “PPP”. PPPoA/PPPoE Select “PPPoE”. User name and The values shall be provided by your ISP. Password Default Route Select “Enable”.

  • Page 92: Pppoa Configuration

    5.3 PPPoA Configuration Configurations on MT800 Location Parameters Comments Select any one from the eight PVCs. VPI/VCI The value shall be provided by your ISP. Operation Mode Select “Enable”. The value shall be provided by your ISP. Encapsulation Usually you can keep the default value: LLC.

  • Page 93: Rfc 2684 Bridged (Pure Bridge) Configuration

    5.4 RFC 2684 Bridged (Pure Bridge) Configuration Configurations on MT800 Location Parameters Comments Select any one from the eight PVCs. VPI/VCI The value shall be provided by your ISP. Operation Mode Select “Enable”. The value shall be provided by your ISP. ATM Setting Encapsulation Usually you can keep the default value:...
  • Page 94 Configurations on MT800 Location Parameters Comments The value shall be provided by your ISP. Usually you can keep the default value: Encapsulation LLC. Connection Type Select “RFC2684 Bridged”. Address Type Select “Static IP”. IP Address and The values shall be provided by your ISP. Subnet Mast Default Route Select “Enable”.

  • Page 95: Rfc 2684 Bridged (Dhcp) Configuration

    5.6 RFC 2684 Bridged (DHCP) Configuration Configurations on MT800 Location Parameters Comments Select any one from the eight PVCs. VPI/VCI The value shall be provided by your ISP. Operation Mode Select “Enable”. The value shall be provided by your ISP. Encapsulation Usually you can keep the default value: LLC.

  • Page 96: Rfc 2684 Route (Ipoa) Configuration

    5.7 RFC 2684 Route (IPoA) Configuration Configurations on MT800 Location Parameters Comments Select any one from the eight PVCs. VPI/VCI The value shall be provided by your ISP. Operation Mode Select “Enable”. The value shall be provided by your ISP. Encapsulation Usually you can keep the default value: LLC.
  • Page 97 Note: For other advanced configurations, please refer to Chapter 4 Web-based Management.

  • Page 98: Chapter 6 Troubleshooting

    Chapter 6 Troubleshooting 6.1 Quick Troubleshooting Failures Instructions Ensure power adapter is well connected; Power light is out. Ensure the right power adapter is used. Ensure the ADSL line is well connected; Ensure the telephone line before entering the house is valid, try to test with a telephone;...

  • Page 99: Faqs

    Failures Instructions Take the most common access mode as an example, in which a dial-up application is installed on the user’s computer: Ensure that any of the problems above is not the reason; Ensure that the dial-up application is correctly installed and set on your PC;...
  • Page 100 Use the default user name: admin and password: admin Q: My configuration is gone after rebooting MT800. If you want to keep your settings after reboot MT800. Please go to Web-based Configuration Manager “Save & Reboot” “Save” to save your configurations. Figure 6-1 Save the changed setting Q: I can’t upgrade with the new firmware.
  • Page 101 without any packet, the ISP will drop the connection. Please contact with your ISP about this problem. Some ISPs don’t provide a good quality ADSL signal line. Therefore, when the ADSL line is unstable, your connection will be dropped. Try with a telephone and find the status of your ADSL signal line.
  • Page 102 (1) Phone Socket (2) Phone (3) Phone (4) RJ-11 Tel Cable (5) Splitter (6) RJ-11 Tel Cable (7) RJ-11 Tel Cable (8) Phone Jack (9) MT800 Figure 6-2 Connect multiple phones-1...
  • Page 103 (1) Phone (2) Phone Socket (3) Phone (4) RJ-11 Tel Cable (5) Micro-filter (6) RJ-11 Tel Cable (7) Phone Socket (8) RJ-11 Tel Cable (9) Splitter (10) RJ-11 Tel Cable (11) Phone Jack (12) MT800 Figure 6-3 Connect multiple phones-2...

  • Page 104: Chapter 7 Technical Specifications

    Chapter 7 Technical Specifications General Specifications ITU-T G.992.1 (G.dmt) ITU-T G.994.1 (G.hs) Standards ITU-T G.992.2 (G.lite) ANSI T1.413 Issue # 2 G.dmt full rate: Downstream up to 8 Mbps Upstream up to 896 kbps G.lite: Downstream up to 1.5 Mbps Data Transfer Rate Upstream up to 512 kbps...
  • Page 105 Note: There might be different power adapter used in different regions. Please make sure that your power adapter is in conformity with the sign in the rear panel (9V AC 1A or 9V DC 1A). Waterproof should be used during the storage, transportation and running of the equipment.

  • Page 106: Chapter 8 Appendix

    Chapter 8 Appendix 8.1 Factory Default Settings User name admin Password admin IP address 192.168.1.1 Subnet mask 255.255.255.0 DSL Mode Multimode PVC0 VPI =0 VCI=35 PVC1 VPI =8 VCI=35 PVC2 VPI= 0 VCI= 100 RFC 2684 Bridged PVC3 VPI =0 VCI=32 Mode PVC4...
  • Page 107 Abbreviation Description Asynchronous Transfer Mode Customer Premises Equipment DHCP Dynamic Host Configuration Protocol Domain Name Server DSLAM Digital Subscriber Line Access Multiplex HTML Hypertext Markup Language Internet Protocols ICMP Internet Control Message Protocol IPoA Internet Protocols Over ATM Internet Service Provider Local Area Network Media Access Control Management Information Base...
  • Page 108 Abbreviation Description Transfer Control Protocol TFTP Trivial File Transfer Protocol User Datagram Protocol Virtual Channel Identifier Virtual Path Identifier Wide Area Network...
  • Page 109 Huawei Technologies Co., Ltd. Administration Building, Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, P. R. China Postal Code: 518129 Website: http://www.huawei.com...

Table of Contents