Chrysler PT Cruiser Quick Reference Manual
2009
Hide thumbs
Also See for PT Cruiser:
- Service & repair manual (2078 pages) ,
- Owner's manual (491 pages) ,
- Owner's manual (368 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Chrysler PT Cruiser
Summary of Contents for Chrysler PT Cruiser
- Page 1 2009 | PT Cruiser Quick Reference guide...
-
Page 2: Instrument Panel
n s t r u m e n t... - Page 3 a n e l Heated Seat Switches • Rear Window Defroster • Hazard Warning • Traction Control Switch • Pass. Airbag On/Off Light • (Refer to Owner’s Manual)
-
Page 4: Driver Seat Adjustment
Power Seat Switch Recliner Lever Driver Seat Adjustment SiX-WAy POWeR SeAT SWiTCH The seat switch is located on the outboard side of the seat near • the floor. Use this switch to move the seat up or down, forward or rearward, or tilt the seat. -
Page 5: Key Fob
Unlock Lock Key Fob LOCking AnD UnLOCking THe DOORS/LifTgATe Press the LOCk button once to lock all the doors and liftgate. • Press the UnLOCk button once to unlock the driver’s door only • and twice within five seconds to unlock all the doors and liftgate. All doors can be programmed to unlock on the first press of the •... -
Page 6: Turn Signal/Lights Lever
e h I c l e e at u Dimmer Fog Lights Lights Push Lever for High Beams Turn Signal/Lights Lever HeADLigHTS/PARking LigHTS Rotate the end of the lever to the first detent for parking lights and • the second detent for headlights. inSTRUMenT PAneL DiMMeR Rotate the center portion of the lever to the extreme bottom position •... -
Page 7: Cruise On/Off
r e s Push ON/OFF Button Speed Control Lever CRUiSe On/Off • Push the On/Off button to activate the Speed Control. • CRUiSe will appear on the instrument cluster to indicate the Speed Control is on. • Push the On/Off button a second time to turn the system off. •... -
Page 8: Fuel Cap
e h I c l e e at u Fuel Cap LOOSe gAS CAP MeSSAge if a “gas cap” odometer message (shown as gASCAP) appears, • tighten the gas cap until a “clicking” sound is heard. Press the odometer reset button to turn the message off. •... -
Page 9: Manual Climate Controls
r e s Push Push Rotate Rotate Rotate Air Recirc. Blower Temp. Mode Button Control Button Control Buttons Manual Climate Controls AiR ReCiRCULATiOn /MAX A/C for maximum cooling, rotate the temperature control to the • MAX A/C position, then push the A/C and recirculation buttons. for window defogging, turn the recirculation button off. -
Page 10: Odometer/Trip Odometer Reset Button
Rear Wiper/Washer Front Wipers Front Washer (pull toward driver) Mist (down) Wiper/Washer Lever fROnT WiPeRS Intermittent, Low and High Operation Rotate the end of the lever to the first detent position for one of five • intermittent settings, the second detent for low wiper operation and the third detent for high wiper operation. -
Page 11: Am/Fm/Cd Radio
Tune Volume Control Control Push Push Push Mode Station Pre-sets Push Time Seek Button for Radio, Scan Button Button Satellite, or Button CD Player AM/FM/CD (6 - Disc) Radio CLOCk SeTTing Press and hold the TiMe button until the hours blink; •... - Page 12 This guide has been prepared to help you get quickly acquainted with your new Chrysler and to provide a convenient reference source for common questions. However, it is not a substitute for your Owner’s Manual. for complete operational instructions, maintenance procedures and important safety messages, please consult your Owner’s Manual,...
Need help?
Do you have a question about the PT Cruiser and is the answer not in the manual?
Questions and answers
my engine light continues to come on the mechanic changed the censors in the exhaust but still keep coming on. he thinks it may be the wiring how do i find out.
To diagnose wiring issues causing the check engine light to stay on in a Chrysler PT Cruiser after replacing the exhaust sensors:
1. Check Diagnostic Trouble Codes (DTCs): Use an OBD-II scanner to read the current codes. For example, code P0304 indicates a cylinder 4 misfire.
2. Inspect Wiring to Sensors: Visually inspect the wiring connected to the camshaft sensor, exhaust sensors, and surrounding components. Look for damaged, frayed, or corroded wires.
3. Test Sensor Connections: Ensure all connectors are securely attached and free of corrosion or bent pins.
4. Check for Previous Repairs: If wiring was previously modified, verify it was done correctly. Poor splices or wrong connections may cause intermittent faults.
5. Use a Multimeter: Test continuity and voltage in the suspect wires to ensure proper signal transmission.
6. Inspect Related Fuses: Check the fuse block for any blown fuses that could affect engine sensors or the powertrain control module.
7. Monitor Live Data: Use a scan tool to observe real-time sensor readings and identify inconsistencies.
If issues persist, have the system inspected by a qualified technician.
This answer is automatically generated