Cycles - Kenmore HE4t 110.4508 Owner's Manual And Installation Instructions

Adding items
This washer allows an 8-minute period in which forgotten
garments may be added to the load. You can add items to the
washer if the ADD A GARMENT status light is glowing.
To add items
1. Select PAUSE/CANCEL The washer door unlocks, and items
can be added.
2. To continue the cycle, close the door and select and hold
START (for approximately 1 second).
3. To unlock the door after the Add a Garment period, press
PAUSE/CANCEL twice. This will cancel the Wash Cycle.
Clothes Clean
The Clothes Clean light stays on for 5 minutes after the cycle is
complete. The washer will then power down.
Locking controls
The Control Lock prevents unintended use of the washer. You
can also use the control lock feature to prevent unintended cycle
or option changes during a cycle. When CONTROL LOCKED is
lit, all buttons are disabled except for Pause/Cancel and Start.
You can lock the controls while the washer is operating.
To lock the controls
Select and hold DRAIN & SPIN for 3 seconds.
DRAIN & SPiN
PRESS & IOLb 3
SECONDS [0 lOCK /
UNLOCK CONIROL
The CONTROL LOCKED status light glows.
To unlock the controls
Select and hold DRAIN & SPIN for 3 seconds until the CONTROL
LOCKED Status light turns off.
Door Locked
When the status light glows, the door is locked.
Estimated Time Remaining
The cycle times vary automatically based on your water pressure,
water temperature, detergent, and clothes load. The cycle time
will be extended if oversudsing occurs or the load is unbalanced.
The SUDs routine removes extra suds and assures proper rinsing
of your garments. During the unbalance routine the time
displayed may pause until this activity is complete, then resume
with the remainder of the cycle.
Wash Cycles
Choose Wash Cycles by selecting the button next to the desired
cycle. Each cycle is designed for different types of fabric and soil
levels.
NOR_,_AL/
CASUAL,
HEAVY
DUTY
WHITEST
WHITES
WASH CYCLES
EXPRESS W ASH
KIDSWEAR
BULKY / BEDDING
SANITARY
Each cycle has a preset Soil Level (cycle time), Water
Temperature, Spin Speed and may have preset Options. The
preset settings provide the recommended fabric care for the
selected cycle.
The preset settings can be changed anytime before START is
selected. Not all Options and Modifiers are available with all
Cycles. (To change settings after the cycle has started, select
PAUSE/CANCEL, then select the desired settings. Select and
hold START [for approximately 1 second] to continue the cycle.)
Preset cycle settings
Each cycle has a preset Cycle Time, Water Temp, and Spin
Speed. The preset settings provide the recommended fabric care
for the selected cycle. See chart.
Cycle Soil Level Water Temp Spin Speed
(hr:min)
Sanitary Heavy Extra Hot/ Extra High
(2:00) Cold
Bulky/Bedding Normal Warm/Cold Extra Low
(o:55)
Whitest Whites Heavy Hot/Cold Extra High
(1:10)*
Heavy Duty Heavy Hot/Cold Extra High
(1:35)
Normal/Casual Normal Warm/Cold High
(0:45)
Express Wash Light Warm/Cold Extra High
(2-3 items) (0:30)
Kids Wear Heavy Warm/Cold Extra High
(1:10)
Handwash/ Normal Cold/Cold Extra Low
Wool (0:35)
Silk/Ultra Normal Cold/Cold No spin
Delicate (0:30)
Soak Normal Warm/Cold No Spin
(0:30)
Rinse & Spin Normal Cold/Cold Extra High
(0:20)
Drain & Spin Normal Cold/Cold Extra High
(0:12)
*Time may be different from that of your model.
Sanitary
Use this cycle to clean heavily soiled colorfast fabrics. This cycle
combines a very hot water temperature and fast-speed tumbling
to help ensure the removal of heavy soils and stains. It is
recommended that you set your hot water heater to 120°F (49°C)
to ensure proper performance during this cycle. The Sanitary
cycle also helps eliminate 99.999% of 3 common infectious
bacteria, even when no bleach is used. Extra high speed spin
helps shorten drying time.
15