Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Clarke WE6480 MIG 95
Summary of Contents for Clarke WE6480 MIG 95
- Page 1 l:l tt'l; j OPERATING & MAINTENANCE INSTRUCTIONS...
- Page 2 Congratulations of the the purchase of your new |_|iill_EO Mig Welder. Before atlempting to operate this machine, please read this instructions manual thoroughly follow all directions carefully. doing so you will ensure the safety of both yourself and others around you, and at the same time, you should look forward to long and trouble free service from your €|iiM_Ul Mig Welder.
- Page 3 1.1 General Instructions Make sure this manual is carefully read and understood by the welder. Location Welding orocesses of any kind can be dangerous not only to the ooerator but to an't oersoq siluated near the eauiement, if safely and ooerafing rules are not strictN observed.
- Page 4 Primary Or Input Power Data MIG 95 Primary Volts 120 Volts Primary Amps 13 Amps Frequency 60 Hz Secondary Or Output Power Data Max. Sec, Volts 27 Volts Peak Sec. Amps 95 Amps DLriy Cycle 60 Amps at 20% Duty Cycle Mig 95 is ratedata 20% du_/cycle.
- Page 5 Thewelder i ssupplied witha welding wirespool. I norderto install this wireintothefeeding system, follow theinstructions andrefer to Figure 2 . 1,Remove t hespool h older [ R} l ocking knob [I},press t helwoclicks {J] a ndextract thewire spool. 2. Remove t heplaslic f l_nfrcr'n thewire spool [K) a ndref:k:_ce ifonthespodhok:Jer [f_). Replace thespool holaer lacking k nob (1) [the sp_ing and the washer fccn the bro_t, ir'g swtem of lt_e wire spool speed].
- Page 6 !_l[e_ I_Vl_ _l_j In MIG welding [Metal Inert Gas) a continuously fed metal electrode is melted into a welding pool at constant and controlled speed. The wire is connected to a constant voltage pole while the work piece is connected to the other pole.
- Page 7 Your welder is supplied with a mini wire spool of about 0.5 pounds of .035" diameter wire. When the wire spool is finished it can be replaced with a 2 pound wire spool. the wire is pushed by a roll which is moved by a series of mechanisms, the roll has two grooves of_e marked by ,035"...
- Page 8 WE20220018 Sit Cable 3x4wgl 4 m 2,5+American Plug Handle WE21600036 WE44400018 Plastic Wire Feeder D.28 Rolls 06-08 WE33805074 Wire Feed Roll D.7x25 0,6x0,8 Side Panel WE33705326 Torch Grommet On Front Panel WE21690001 WE22200006 Wel_ng Cuffent Switch 16A 250V Patentiometer Knob WE21690018 WE22200002 On/Off Switch...
- Page 9 llSV << E 0585...
- Page 10 WE21690343 Complete Torch Handle WE21690340 Trigger WE23005011 Torch Gas Valve For No Gas T 1.0 Torch WE23005145 Torch Neck For Twl Torch WE23005091 Thread Guide Wire Liner X T Neck 1.4 WE23005090 Torch Neck Insulator 1.4 Torch E3 WE23005146 Gas Diffuser For Torch Twt Me-99 WE23005020 1,0mm...
- Page 11 OPEN SQUARE BUTT JOINT CORNER JOINT varies ft_m l.emm to 4 8ram @eperdirg pl3te th_kr_ss SINGLE BUT[ JOINT SINGLE FILLET LAP JOINT - .7/ LESS THAN 70" "\ /• 1.6ram > DOUBLE VEE BUTT JOINT LESS THAN 70" DOUBLE FILLET LAP JOINT 11 fill 1.6ram...
- Page 12 ® WE6480 MIG 95 (_, OPERATING MANUAL COD.77610490...
Need help?
Do you have a question about the WE6480 MIG 95 and is the answer not in the manual?
Questions and answers