Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Velodyne MicroVee
Summary of Contents for Velodyne MicroVee
- Page 1 USER’S MANUAL Audio/Video Subwoofer System 120V/230V...
- Page 2 Enjoy. Thank you for choosing a Velodyne. Our passion for high performance, low-distortion bass is the driving force behind our worldwide reputation in audio and technical innovation. We are pleased to bring the Velodyne sound experience to your home.
- Page 3 MicroVee User’s Manual - i...
-
Page 5: Table Of Contents
Velodyne Products ........ -
Page 7: Congratulations
To prevent fire or shock hazard, do not expose this equipment to rain or moisture. To avoid electrical shock, do not open speaker enclosure or amp chassis cover. Please observe all warnings on the equipment itself. There are no user serviceable parts inside. Please refer all service questions to your authorized Velodyne dealer or service representative. -
Page 8: Placement Of Your Subwoofer
PLACEMENT OF YOUR SUBWOOFER The first step in installing your new MicroVee is to determine where it will be placed in the room. Unpack the system carefully and use the following guidelines in order to find the best room placement option. -
Page 9: Installation
INSTALLATION Your new Velodyne subwoofer provides for a number of installation options. Read all the installation information below in order to determine which installation option is best suited for your system. Remember to perform all installation procedures with system power turned off to prevent possible damage. - Page 10 The correct position will have a greater amount of apparent low frequency output. Crossover Switch - INTERNAL X-OVER/SUBWOOFER DIRECT This switch allows the microVee’s internal crossover circuitry to be bypassed. This is required in certain installations which route the signal through external processors with a crossover circuit of their own. Simply move the switch to SUBWOOFER DIRECT to disengage the built-in crossover.
- Page 11 In these installations you may need to bypass the crossover in either the processor or the MicroVee. In some installations, simply setting one crossover to a higher frequency (such as 120 Hz) will restore maximum performance. To bypass the subwoofer’s internal crossover when the unit is being fed a low pass signal from another crossover, simply locate the switch marked INTERNAL X-OVER/SUBWOOFER DIRECT on the rear panel of the subwoofer and set to the SUBWOOFER DIRECT position.
-
Page 12: Lfe Connection - Option A
“lFe Out” or “Subwoofer Out” on the back of your receiver will pass into your Velodyne subwoofer. This connection is the most common connection method when using your subwoofer with a 5.1 receiver. (Cable needed: 1 mono RCA cable.) - Page 13 “wake up” even when signal is present. If this occurs, simply use a “y” adapter (available from most dealers) to allow your processor’s single sub line to be fed into both l&R inputs. This will make the unit turn on at lower signal levels. www.velodyne.com MicroVee User’s Manual - 7...
-
Page 14: Mini-Jack Connection - Option B
Use the supplied cable to connect from the output of your dock, computer or gaming console to the input jack of the microVee. connect the satellite speakers into the thru-jack on the back of the microVee subwoofer. (Cable supplied by Velodyne: 6 foot, 1/8” (male) to 1/8” (male) stereo cable.) Figure 2. -
Page 15: Speaker-Level Connection - Option C
SPEAKER-LEVEL CONNECTION - OPTION C Figure 4 shows an easy way to connect your Velodyne subwoofer directly to your receiver or integrated amplifier if it lacks line-level outputs. You may also connect your satellites directly to your receiver or amplifier along with the subwoofer. -
Page 16: Interconnnect Cables
INTERCONNECT CABLES when installing your new Velodyne subwoofer using the line level connections, you should always use shielded phono cables. There are many quality cables available. we recommend that you keep the length of cable as short as possible to avoid any potential noise problems. -
Page 17: Troubleshooting And Service
2. The unit does not appear to operate normally or exhibits a marked change in performance 3. The unit has been exposed to water 4. Some part of the chassis or circuitry is physically damaged Thank You for Purchasing a Velodyne MicroVee Subwoofer System! www.velodyne.com MicroVee User’s Manual - 11... -
Page 18: Specifications
9” x 9” x 9.6” (22.9 x 22.9 x 24.4 cm) Cabinet Sealed enclosure Warranty (parts/labor) Three years (electronics - parts and labor), Five years (drivers - parts and labor) Shipping Weight (approx) 20 lbs. (9.1 Kgs) Specifications are subject to change without notice. 12 - MicroVee User’s Manual www.velodyne.com... -
Page 19: Velodyne Products
Sc-600 Amp CHT-Q Series SPl-1000i Sc-602 Amp CHT-8Q Sc-600 Iw CHT-10Q SPl-Ultra Series Sc-600 IF/Ic CHT-12Q SPl-800 Ultra CHT-15Q SPl-1000 Ultra VX-10 Series II SPl-1200 Ultra Impact Series Impact - mini Impact -10 Impact -12 www.velodyne.com MicroVee User’s Manual - 13... -
Page 20: For Your Records
PRODUCT MODEL: PRODUCT SERIAL NUMBER: NOTE: If you need to file a warranty claim for your product, you will still need to submit to Velodyne the original sales invoice or other proof of ownership and date of purchase. Please validate your product warranty by completing the warranty registration online within 30 days at: velodyne.com/warranty-subwoofers... - Page 24 MicroVee_RevH_MAY2012 Velodyne Acoustics, Inc. 408.465.2800 voice Service E-mail: service@velodyne.com 345 digital drive 408.779.9227 fax Product E-mail: help@velodyne.com Morgan Hill, CA 95037 408.779.9208 service fax Technical E-mail: techhelp@velodyne.com www.velodyne.com...
Need help?
Do you have a question about the MicroVee and is the answer not in the manual?
Questions and answers