Page 2
Enjoy. Thank you for choosing a Velodyne. Our passion for high performance, low-distortion bass is the driving force behind our worldwide reputation in audio and technical innovation. We are pleased to bring the Velodyne sound experience to your home.
CONGRATULATIONS congratulations on your purchase of a Velodyne subwoofer system. This system represents the state-of-the- art in low frequency reproduction and will provide you with years of listening pleasure when properly cared for. Read and follow this instruction manual to insure safe and proper system connection and operation.
Avoid these locations when possible. when using a pair of Velodyne subwoofers in stereo, it is preferable to place each subwoofer by the satellite of the same channel.
Simply move the switch to SUBWOOFER DIRECT to disengage the built-in crossover. For all other installations which do not have a separate electronic crossover, we recommend you leave the switch set to INTERNAL X-OVER to provide optimum performance. www.velodyne.com MiniVee User’s Manual - 3...
Subwoofer Outputs The Velodyne subwoofer is designed to operate using the full range audio signal for input when using the built- in crossover. Some processors/receivers have a “subwoofer out” jack that is internally filtered and designed to be used with a conventional amplifier and speaker. In some rare cases, combining both an external crossover and the one internal to the subwoofer may result in low output and increased noise. In these installations you may need to bypass the internal crossover in either the processor or Velodyne subwoofer.
Page 11
“y” adapter (available from most dealers) to allow your processor’s single sub line to be fed into both l&R inputs. This will make the unit turn on at lower signal levels. www.velodyne.com MiniVee User’s Manual - 5...
RcA cables from the outputs on the back of your subwoofer to the inputs on the back of your amplifier. When the subwoofer is installed in this fashion, your satellite speakers will be crossed over at 80 Hz which removes the lower bass frequencies from your external amplifier and speakers, enabling them to do a better job reproducing the higher frequencies. By utilizing this method, you will have a bi-amplified system, gaining improved power and headroom for your system. This installation method is not as common as the method described in Figure 1. (Cables needed: 2 stereo pair of RcA cables.) Figure 2. Installation Using Stereo Line-Level Inputs 6 - MiniVee User’s Manual www.velodyne.com...
Caution!!! To avoid damage to your main amplifier, be sure to maintain correct polarity when making all connections. Red (positive) to red, and black (negative) to black. Be sure that all connections are tight, and that there are no loose strands or frayed wires. www.velodyne.com MiniVee User’s Manual - 7...
SUBWOOFER OUTPUTS The Velodyne subwoofer is designed to operate using the full range audio signal for input when using the built- in crossover. many home theater processors/receivers (dolby digital , dTS , THX™) have a “subwoofer out” ® ® jack that is internally filtered and designed to be used with a powered subwoofer. In these installations, you may bypass the internal crossover in either the processor or the Velodyne subwoofer. In some installations, it may be beneficial to have a steeper ultimate crossover slope. To do this, you can use both your processor’s...
CARE OF YOUR SUBWOOFER your Velodyne subwoofer does not require any regular maintenance. normal dusting or cleaning of the surface for appearance purposes are all that is required. we suggest you avoid any harsh detergents or chemicals when cleaning the cabinet. Abrasives, detergents, or cleaning solutions may damage the finish on the cabinet. We recommend using only a damp cloth to clean the cabinet.
Under more serious conditions, the unit may shut off completely. Normal operation should return upon cooling, but you may be required to turn the power off and then on again to reset the unit. The following conditions require service by a qualified technician: 1. The power cord has become damaged 2. The unit does not appear to operate normally or exhibits a marked change in performance 3. The unit has been exposed to water 4. Some part of the chassis or circuitry is physically damaged Thank You for Purchasing a Velodyne MiniVee Subwoofer System! 10 - MiniVee User’s Manual www.velodyne.com...
Sealed enclosure Warranty (parts/labor) Three years (electronics) Three years (electronics) Five years (drivers) Five years (drivers) Shipping Weight (approx) 33 lbs. (15 Kgs) 45 lbs. (20 Kgs) Specifications are subject to change without notice. www.velodyne.com MiniVee User’s Manual - 11...
The warranty information indicated above refers to products purchased in the United States and Canada only. If you purchased your product outside of the United States or Canada, please consult your local authorized Velodyne dealer for warranty registration and information.
Page 20
MiniVee_RevF_MAY2012 Velodyne Acoustics, Inc. 408.465.2800 voice Service E-mail: service@velodyne.com 345 digital drive 408.779.9227 fax Product E-mail: help@velodyne.com Morgan Hill, CA 95037 408.779.9208 service fax Technical E-mail: techhelp@velodyne.com www.velodyne.com...
Need help?
Do you have a question about the MiniVee and is the answer not in the manual?
Questions and answers