G-System Split With "Gfx01" In A Rack - TC Electronic G-System User Manual

TYPICAL SETUPS
G-System Separated:
GFX01 in a Rack
L O O P 1 L O O P 2 L O O P 3 L O O P 4 I N S E R T O U T P U T
R
R E T U R N R E T U R N R E T U R N R E T U R N
S E N D S E N D S E N D S E N D 4 x 5 0 m A o r 2 0 0 m A t o t a l l y
Q U A D 9 V D C O U T P U T S
( m o n o )
I N S T R U M E N T
I N P U T P O W E R O U T P U T S
L
Rackmount
CONTROL LINK SCHEMATICS
PUSH
IN AD FILTER COMP
GFX01 | EFFECTS PROCESSING UNIT
Drive Pedals
Connections
• Unmount the GFX01 (the 19" unit) from underneath
the Control Board by unscrewing the four 6mm
screws.
• Replace the short CAT 5 cable with a longer cable.
• Mount the 19" GFX01 in your rack.
Please note that some racks require 5mm screws,
while others require 6mm screws. The G-System
is assembled using 6mm screws. Use appropriate
screws for your rack.
For advice on how to connect the drive and
expression pedals, please refer to the descriptions
on the previous pages.
28
S W O U T P E D A L I N I N M I D I O U T
A U D I O E Q U I P M E N T
P R O F E S S I O N A L 1 0 0 - 2 4 0 V A C 5 0 - 6 0 H z , 1 5 W
G F 0 0 1 | M A D E I N T H A I L A N D
O U V R I R .
A V I S : R I S Q U E D E C H O C E L E C T R I Q U E - N E P A S
R A I N O R M O I S T U R E # 1 0 8 0 9 3
S H O C K D O N O T E X P O S E T H I S E Q U I P M E N T T O C S A F I L E
2 T O R E D U C E T H E R I S K O F F I R E O R E L E C T R I C E N / I E C 6 0 0 6 5
E X P . W A R N I N G U L 6 5 0 0
D O D O N O T O P E N C U S
R I S K O F E L E C T R I C S H O C K
C A U T I O N R
O U T P U T
O P E R A T I O N S U B J E C T T O C O N D I T I O N S S T A T E D I N T H E M A N U A L .
1 V O L S E R I A L # U S B S / P D I F C A U S I N G E Q U I P M E N T R E G U L A T I O N S A N D C O M P L I E S W I T H P A R T 1 5 O F T H E F C C R U L E S .
T H I S C L A S S B D I G I T A L D E V I C E M E E T S A L L R E Q U I R E M E N T S O F T H E C A N A D I A N I N T E R F E R E N C E -
STATUS INPUT
EXT EFF 1 EXT EFF 2 EXT EFF 3 EXT EFF 4 PREAMP
DIGITAL OUT
INSTRUMENT
OUT L
DA LOOP 1 LOOP 2 LOOP 3 LOOP 4 INSERT AD MOD PITCH DELAY REVERB DA
OUT R
LINK PWR
Preamp
FILTER COMP LOOP 1 LOOP 2 LOOP 3
FORMANT | WAH | EFFECT FILTERS COMPRESSOR ALGORITHM
ENCODER ENCODER ENCODER ENCODER ENCODER
GAIN ADJUST EDIT PARAMETER A EDIT PARAMETER B EDIT PARAMETER C SELECT PAGE
INPUT DAMP EDIT A EDIT B EDIT C
INTEGRATED EFFECTS
E1: E2: E3: E4: E5: +MANAGEMENT
COM FLT PIT DLY REV
EDITED
GLOBAL TEMPO
UP MOD PITCH DELAY REVERB
MENU MODE CHORUS | FLANGER | TREMOLO WHAMMY | PITCH ALGORITHM HI-CLASS | TAPE ECHO | DYNAMIC REVERB ALGORITHM
DOWN HOLD TO STORE HOLD TO STORE HOLD TO STORE HOLD TO STORE
ENTER | RETURN
Important!
When the GFX01 is separated from the Control
Board, we strongly recommend mounting a 1
unit standard blank faceplate instead to ensure
maximum stability.
If you do not use a Cat 5 plug with angled
XLR housing, you can turn the wings that
are holding the blank faceplate by 180
degrees to make space for a normal XLR
plug.
This is easily done:
• Unscrew the two screws in each side-panel.
• Turn the wings by 180 degrees.
• Mount the wings again using the screws.
EDIT TAP TEMPO
ENCODER
LEVEL SET
BOOST
PRESETABLE BOOST LEVEL
HOLD TO STORE