Advertisement
Table of Contents
- 1 Carton Contents
- 2 Roller Assembly
- 3 Grassbox Assembly
- 4 Mulching Plug
- 5 Cutting Height Adjustment
- 6 Starting and Stopping
- 7 Removing and Fitting the Blade
- 8 Caring for Your Lawnmower
- 9 Replacement Parts
- 10 Fault Finding Hints
- 11 Service Recommendations
- 12 Environmental Information
- 13 EC Declaration of Conformity
- Download this manual
Advertisement
Table of Contents
Related Manuals for Flymo MULTIMO 340XC
Summary of Contents for Flymo MULTIMO 340XC
- Page 1 Original Instructions Multimo 340XC Multimo 340XC ® Multimo 360 Multimo 360XC Multimo 420 Multimo 420XC Multimo 360 Multimo 420 Multimo 360XC Multimo 420XC...
-
Page 2: Carton Contents
2 mulching plug lock off button start/stop lever bolt upper handle roller half x 2 mulching plug PAGE 1 switchbox Multimo 340XC Easi-Reel grassbox cable spool handle upper instruction manual switchbox Multimo 360 Multimo 420 grassbox handle instruction manual grassbox... - Page 3 IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. The Loose Parts Pack is packaged underneath the deck of the product. IF ANY PARTS ARE MISSING CONTACT:- Husqvarna UK Ltd. Customer Service Department direct...
- Page 4 12. Never pull on the cable to disconnect any of the plugs. 13. Use only on AC mains supply voltage shown on the product rating label. 14. Flymo Products are double insulated to EN60335. Under no circumstance should an earth be connected to any part of the product. Preparation While using your product always wear substantial footwear and long trousers.
-
Page 5: Roller Assembly
3. Only use extension cables specifically designed for outdoor use. CONNECTORS - IMPORTANT • Flymo connectors are suitable for use with 2 core cable only. Under no circumstances should these connectors be used for earthed products. • All Flymo connectors and cables are of splashproof construction. - Page 6 Assembly of Lower Handles to Lawnmower 1. Pull the lower handle bolt until it locks into position as illustrated in fig C1. 2. Place the Spring over the Bolt (C2) 4. Insert the Barrel Nut into the Cam Lock as illustrated in fig D1.
-
Page 7: Grassbox Assembly
Assembly of Upper Handles to Lower Handles 1. Insert the Barrel Nut into the Cam Lock as illustrated in fig E1. 2. Attach the Upper Handle to the Lower Handle with the Round Headed Bolt, Washer and Cam Lock as 4. -
Page 8: Mulching Plug
grassbox full How to Mow Your product can be used to cut grass using the following methods:- 1. Grassbox Fitted:- grass is collected effectively and compacted into the grassbox. (K) 2. Rear Discharge:- Effectively cuts long grass with no need to empty the grassbox (L) 3. -
Page 9: Cutting Height Adjustment
Cutting Height Adjustment • Height of cut is adjusted by raising or lowering the wheels using the height adjustment lever (Q) • There are five heights of cut on this product. • NOTE A medium height of cut is recommended for most lawns. -
Page 10: Caring For Your Lawnmower
Cleaning Easi-Reel cable winder (XC Models only) 1. Lift grassbox lid, squeeze together the two catches (Z7) and remove the cable spool. 2. Clean the cable spool (Z8) and the area it was located with a soft brush (Z9) 3. Replace the cable spool, ensuring it clicks into place. Storing your Lawnmower: •... -
Page 11: Fault Finding Hints
Easi-Reel Cable Winder (XC models only) Fails to Operate 1. Is the correct Starting procedure being followed? See ‘To Start your Lawnmower’ 2. Is the Power Turned On? 3. Check the fuse in the plug, if blown replace. 4. Fuse continues to blow? Immediately disconnect from the mains electricity supply and consult your local approved Service Centre. -
Page 12: Ec Declaration Of Conformity
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice. Copyright © 2008 Flymo S.A. All rights reserved. Flymo® and other product and feature names are registered or unregistered 5100693-02 Guarantee &...
Need help?
Do you have a question about the MULTIMO 340XC and is the answer not in the manual?
Questions and answers