Table of Contents
Advertisement
Quick Links
Installation Instructions
IMPORTANT:
Read and save
these instructions
IMPORTANT
Installer: Leave Installation Instructions
with the owner.
Owner: Keep Installation Instructions for
future reference.
Save Installation Instructions for local
electrical inspector's use.
www.whirlpool.com
Actual unit may or may not contain windows in doors depending on model.
COMMERCIAL
STACKED DRYER
GAS
ELECTRIC
120-volt, 60 Hz
120/240-volt, 60 Hz
Part No. 8527813
®
COMMERCIAL
LAUNDRY
PRODUCTS
Advertisement
Table of Contents
Related Manuals for Whirlpool 8527813
Summary of Contents for Whirlpool 8527813
-
Page 1: Installation Instructions
Installation Instructions Actual unit may or may not contain windows in doors depending on model. Part No. 8527813 IMPORTANT: Read and save COMMERCIAL these instructions STACKED DRYER ELECTRIC IMPORTANT Installer: Leave Installation Instructions with the owner. 120-volt, 60 Hz 120/240-volt, 60 Hz Owner: Keep Installation Instructions for future reference. -
Page 2: Before You Start
Before you start... IMPORTANT SAFETY INSTRUCTIONS WARNING — To reduce the risk of fire, electric shock, or injury to persons when Your safety and the safety of others are very important. using your appliance, follow basic precautions, including the following: We have provided many important DANGER safety messages in this manual... -
Page 3: Exhaust Requirements
timing cam ratchet tooth The collar houses the accumulator The exhaust system should be timers with actuating arm and button. inspected and cleaned yearly. The timers are set to provide 45 Replace any plastic or metal foil minutes (4 pins) of drying time when exhaust vent with rigid metal or activated by the coin slide. -
Page 4: Gas Dryer
Vents entering Whirlpool Service Manual, “Exhausting from the opposite side should be Whirlpool Dryers,” Part No. 603197, Gas requirements staggered to reduce the exhausted available from your Whirlpool parts air from interfering with the other distributor. -
Page 5: Recommended Ground Method
Recommended Check that dryer is equipped If rigid ground method with the correct burner for the pipe is used particular type of gas used. Burner as a gas supply line, a The dryer, when installed, must be information can be found on the combination of pipe fittings must electrically grounded in accordance serial/rating plate in the door well of... - Page 6 Now Start... Carefully move dryer into final position. Place level on top of With dryer in laundry area. the dryer, first side to side; then front to back. If the dryer is not level, adjust WARNING the legs of the dryer up or down until the dryer is level.
-
Page 7: Electric Dryer
Now Start... Electric Dryer With dryer in laundry area. Electrical requirements WARNING If codes permit and a separate Excessive Weight Hazard ground wire is used, it is Use two or more people to move and recommended that a qualified Secure coin slide mechanism install dryer. - Page 8 Power supply cord Direct wire Disconnect the power supply. external ground Use a new UL-approved power supply WARNING conductor screw cord rated 240-volt min., 30 amperes and marked for use with a clothes dryer. hold- terminal down block screw WARNING cover Fire Hazard Remove hold-down screw...
- Page 9 Four-wire connection... Four-wire receptacle POWER SUPPLY CORD Remove center terminal block screw. Remove appliance ground wire spade (green with yellow stripes) from terminals with external ground connector screw. upturned ends Fasten under center, silver-colored terminal block screw. Connect ground wire (green or 3/4"...
- Page 10 Three-wire connection... Three-wire receptacle POWER SUPPLY CORD Where local codes permit connecting cabinet-ground conductor to neutral wire: Loosen or remove center spade terminal block screw. terminals with upturned ends Connect the neutral wire (white or center) of power supply cord to the center, silver-colored terminal ring terminals...
- Page 11 Three-wire connection... Three-wire receptacle DIRECT WIRE OR Where local codes Do Not permit POWER SUPPLY CORD connecting cabinet-ground conductor to neutral wire: After reattaching the terminal cover, connect a separate copper ground wire from the external Three-wire power supply cord must Remove center terminal block ground connector screw to an have three, No.-10 copper wires and...
-
Page 12: Recessed Area And Closet Installation Instructions
Companion appliance spacing should be 23-3/4" 29-1/4" approx. 1" considered. (60.3 cm) (74.3 cm) (2.5 cm) Part No. 8527813 Prepared by Whirlpool Corporation, Benton Harbor, Michigan 49022 Printed in U.S.A. © 2001 Whirlpool Corporation...