Operating Jvc's Audio/Video Components; Operating Audio Components - JVC RX-7030VBK Instructions Manual

Operating JVC's Audio ideo Components
You can operate JVCb audio and video components with this receiver's remote control, since control signals for JVCb
components are preset in the remote control
IMPORTANT:
lb operate JVC's audio components using the supplied remote
control:
• You need to connect JVC's audio components thr,_)ugbthe
COMPU LINK (SYNCHRO) jacks (see page 41 ) in addition m
the connections using cables with RCA Nn plugs {see pages 11 m
• Aim the remote coning directly at the remote sensor on the
receiver.
• If you use the buttons on the t_mntpanel to choose a source, the
remote control will not operate that source. 3b operate a sotrrce
with the remote control, the source must be selected using sotrrce
selection buttons on the remote canto)l.
• 3b operate the target component using the COMPU LINK remote
control system, set the sotrrce name correctly if required. (See
page 210
• Refer also m the manuals supplied with yotrr components.
For RX4!O30VBK:
* VVhen you p_css one of the soffrce .selection
buttons,
the remote
oparadon
mode appears on
the display
window fee about two hours.
B_ttons Indications
FM/AM TUNER
CD CD
CDR CDR
PHONO PHONO
TAPb2JM D TAPE
VCR [ TAPE
CONTROL repeamdlv)* _ CDI)SC 2 CI)R
SOUND SOUND
By pressing CONTROL repeated_ you can select %'CR 1
_7-APE7 _C,DR_ or _DDSC" as the source,
- When you press one of the following buttons, the remote
o_atlon
m_c appears on the
di@ay
window for about two
hours.
B_ttons Indications
FRONT•[. ERL
FNON'I*R ERR
CENTER (TI'R
SURR*L SURRL
SURR•R SURRR
SURR BACK SBK
SUBWOOEER
S _'R
DIGFIAL EQ EQ
You can aIways peffoml the fullowing oparadons:
FMiAM: Alternate between EM and AM.
After pressing FM/AM, you can perfc_ma the t'olIowing operations
on a tl.lner_
1 - 113/0, + 10: Selact a pre_t channel numbar directly.
For channel numbar 5, press 5.
For channel numbar 15, press +10, then 5.
For channel numbar 20, press +10, then 1010.
TUNING UPIDOWN:
Ttme into stations.
FM MaD E: Change the FM reception m_c.
Sound control section [Amolifiort
You can aIways perform the fullowing oparadons:
SURROUND:
'I_m on and select Surround modes
DSP:
P, l m on and select DSP mc_cs.
SU RRiDSP OFF: l'am off Surround and DSP modes.
FRONT,R then LEVEL +/-:
CENTER then LEVEL +/-:
SURR,L then LEVEL +/-:
SURR,R then LEVEL +/-:
SURR BACK:
After pressing SOUND, you can perform the fallowing oparadons:
FRONT*L than LEVEL +/-: Adjust the lea front speaker output
levcI.
Adjust the right front speaker output
level
Adjust the center speaker output level.
Adjust the left summnd speak_rr
output level.
Adjust the right strrmund speaker
output level.
Adjust the surround back speaker
output level.
SUBWOOFER then LEVEL +/-:
Adjust the subwoofcr output level.
DIGITAL EQ than LEVEL+i-: Select the sound frequency bands
and adjust its level.
TEST: P, l m on _r off test mac output.
BASS BOOST: l'am on o'r off Bass Boost.
Note:
After adjusting sounds, press the corresponding source selection
button to operate your target source by using the 10 keys; otherwise,
t#e 10 keys cannot be used for operating your target source.
After pressing CD, you can peffc_ml the folIowing operations on a
CD player:
I_: St_Laplaying.
I,_<1:
Return to the beginning of the ctrrrcnt (or previous)
track.
I_1_: Skip to the beginning of the next track.
I1: Stop playing.
tl; Patlse playing, lib restmae, press _,
1 - 10/0, +10:
Selec_ a track numbar directly.
F_r track number 5, press 5.
F_r track number 15, press +10, then 5.
F_r track numbar 20, press +10, then 10/0.
P:c_r t rack numbar 30, press +10, +10, then 1010.
44