Advertisement
ASSEMBLE THESAWGAGES
See Figure 4.
SOUARE
MITER/RIP FENCERAIL
HEADBOLT_
(LONGMITERFENCERAIL)
1/4in. WASHER _,_
_.,
\
MITER/RIP FENCERAIL
_
(LONGRIPFENCERAIL)
RIGHTPOSITIVE
STOPBRACKET MITER
_._,_
INDICATOR
PIVOT
SOUARI
HEADBOLT
PLAS_TE
l_in.
SCREW
WASHER
T-NUTS
t
KNOB
SUPPORT
SAW
NUT
BRACKET/
GAGESLOT
LEFTPOSITIVE
/
STOPBRACKET
/
WASHER
HEXBOLT
(7/8in.)
WORK
KNOBBOLT
SUPPORTBRACKET
Fig. 4
•
Place a saw gage into each end of the long miter
fence rail. Correct orientation of the saw gage to
the rail is important. Align the slot in the saw gage
with the slot in the rail. See Figure 4.
•
Secure both saw gages to the rail with 8-16 x 5/8
in. plastite screws provided. The long miter fence
rail has tapped holes on the bottom at each end.
Place screws through these holes and thread into
the pilot holes in the saw gages.
Note: If the screw holes in saw gages become
stripped after extended use, turn them over and
secure to the opposite ends of rail. Pilot holes have
been tapped on both the top and bottom of saw
gages.
•
Tighten screws securely.
ASSEMBLE
THE MITER FENCE HOLDER AND
THE ADJUSTING
CLAMP
Reassemble the miter fence holder and the adjusting
clamp. Place the miter fence holder supplied with your
table saw on the long miter fence and secure to the
sliding miter table, See Figure 5.
ASSEMBLE
THE SUPPORT
BRACKET
See Figures 4 and 5.
The supportbracket attaches to the bottom of long
miter fence and sliding miter table. As the name
implies it provides support and stability for the long
miter fence rail.
•
Orient the support bracket as shown in figure 5.
Slide the bracket under the edge of the sliding
miter table.
•
Secure the support bracket to the bottom of the
long miter fence with a 5/16 in. washer and
5/16 -18 x 7/8 in. hex bolt.
Note: Thread the hex bolt into a 5/16 in. t-nut
closest to the table saw.
•
Tighten the bolt securely.
ASSEMBLE
THE POSITIVE
STOP BRACKET
See Figures 4 and 5.
Two positive stop brackets have been provided for
use as gages when making repetitive cuts, One each
is provided for left or right side application,
•tnsert
the square head boStin the slot in the rip
fence. See Figures 4 and5.
•
Attach the positive stop bracket to the long miter
fence and secure with a 1/4 in. washer and
1/4-20 knob nut.
•
Place either of the left or right positive stop
brackets at the desired position on the rail for
repetitive cuts, etc.
•
Tighten the knob nut securely.
ASSEMBLE
THE WORK SUPPORT
BRACKET
See Figures 4 and 5.
The work supportbracket attaches to the bottomof
long miter fence. As the name implies it provides
supportand stability for long workpieces when making
miter cuts on long stock.
•
Attach work supportbracket to bottomof long miter
fence as shown in figures 4 and 5,
•
Secure the bracket with a 5/16 in. washer and a
5/16-18 x 1/2 in. knob bolt. Thread the knob bolt
into the remaining 5/16 in. t-nut in the bottom
channel or the rail.
•
Tighten the knob bolt securely.
5
Advertisement
