1. Manuals
  2. Brands
  3. Craftsman Manuals
  4. Saw
  5. 113.198411 Operators
  6. Operator's manual

Craftsman 113.198411 Operator's Manual

10-inch deluxe electronic radial saw
Hide thumbs Also See for 113.198411:
Table of Contents

Advertisement

Quick Links

Save This Manual
For Future Reference
SEARS
Operators
Manual
MODEL NO.
113.198411
10" DELUXE ELECTRONIC
RADIAL SAW WITH
44" CABINET AND
2 DOORS
or
113.198611
10" DELUXE ELECTRONIC
RADIAL SAW WITH
44" CABINET AND
6 DRAWERS
Serial
Number
Model and serial numbers
may be found at the rear of
the base,
You should record both
model and serial number in
a safe place for future use.
CAUTION:
READ ALL
INSTRUCTIONS
CAREFULLY
\
MODEL
113.198611
MODEL
113.198411
CRRFTSMRN
10-INCH DELUXE ELECTRONIC
RADIAL SAW
• Assembly
• Operating
• Repair parts
Sold
by SEARS,
ROEBUCK
AND CO., Chicago,
IL. 60684 U.S.A.
Part No. SP5105
Printed in U.S.A.

Advertisement

Table of Contents
loading

Related Manuals for Craftsman 113.198411

Summary of Contents for Craftsman 113.198411

  • Page 1 Save This Manual For Future Reference SEARS Operators Manual MODEL NO. 113.198411 10" DELUXE ELECTRONIC RADIAL SAW WITH 44" CABINET AND 2 DOORS MODEL 113.198611 113.198611 10" DELUXE ELECTRONIC RADIAL SAW WITH 44" CABINET AND 6 DRAWERS MODEL 113.198411 Serial CRRFTSMRN Number Model and serial numbers...
  • Page 2 FULL ONE YEAR WARRANTY ON CRAFTSMAN RADIAL SAW If within one year from the date of purchase, this Craftsman Radial Saw fails due to a defect in material workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE...
  • Page 3 Safety Information The operator's manual contains safety infor- Major Hazards marion, instructions and signs for your protec- tion against serious injuries, including: 1. Workpiece Kickback Loss of fingers, hand, or leg from contact Kickback is an uncontrolled grabbing with the saw blade. throwing of the workpiece during...
  • Page 4 3. Wrong Feed Wrong way feed is feeding the workpiece into the end of the saw with the anti-kickback pawls. The workpiece can be grabbed by the can be blinded. blade and pull your hands into the blade before you can let go or pull back. Fingers, Wear safety hand or arm can be cut off.
  • Page 5 Safety Personal Safety 1. Wear safety goggles labeled "ANSI Z87.1" 1. Keep guards and anti-kickback pawls in place and in working order. on the package. Do not wear regular glasses, they are not safety glasses. 2. Check for broken or damaged parts before 2.
  • Page 6 14.Rip workpieces that are longer than the Safety Labels on the Radial Arm Saw diameter of the blade being used.Do not rip The following labels are on your radial arm a workpiece that is shorter than the diameter saw. Locate, read and follow the safety in- of the blade being used.
  • Page 7 Putting Your Saw Together of each of the smaller boxes together Your radial arm saw is easy to put together, however it will take time. Ask a friend separate from the others. This will help you identify and locate the parts you need during help, and follow these assembly instructions.
  • Page 8 The following parts are included with model 113.198411: Basic Saw Assembly ....A° Operator's Manual ....Cabinet Box ...... Medium Screwdriver Loose Parts Bags ....Trim Caps ....... 7/16" Wrench Trim Ledge ...... #2 Phillips Screwdriver 1/2" Wrench Rear Table .......
  • Page 9 Slotted Screws 1/4-20x7/16 ..The following loose parts are included with model 113.198411: Truss Head Bolts I/4-20x7/16 ..Hex Nuts 1/4-20 ....Leveling Feet ..... Lockwashers 1/4 ....Hex Nuts 3/8-16 ....Spacers ......Truss Head Bolts 1/4-20xl/2 ..Truss Head Bolts 1/4-20xl ..
  • Page 10 The following loose parts are included with both models: Handwheel ....... ©° Arbor Wrenches ....©v Yoke Plug ....... I}i; R Yellow On/Off ....Battery 6V, alkaline, size J ..Motor Support ....Pan Head Screw 10-32xl/2 ..G° Lockwasher 10 ....
  • Page 11 1. Turn the shelf upside down on the floor. The wide edge should point down, and the three narrow edges should point up. (Figure 18) Fig. 16 - Truss Head Bolt, Lockwasher, Hex Nut Rear Shelf Stiffener 4. As you assemble your radial arm saw, some of the holes in the parts will line up and others...
  • Page 12 6. Put truss head bolts through the eight holes indicated. Put a lockwasherand hex nut on eachbolt tighten using a 7/16 inch wrench or socket. 7. Put a comer bracket in each corner of the shelf (Figure Long End Of Shelf Fig.
  • Page 13 6. Put a groovedpin through the hole in the of identical parts. These will be put together rod. into left and right foot assemblies which are mirror images of each other. (Figure 7. Put a washer and spring in place on the bot- tom of the rod, and then slide the rod all the way down.
  • Page 14 15. Screw the leveling foot into the rod until 9. Apply a few drops ofoil (SAE No. 10W-30 the hex nut reaches the bottom of the rod. automotive engine oil) to the lever where (Figure passes through the square hole in the rod. 10.
  • Page 15 2. Lock the lever on the right foot assembly 2. Grease the twelve center slides on top and the down position. bottom using the grease packets included with your saw. 3. Attach this foot assembly to the right side 3. Slide each center slide into an outer bracket. panel by sticking the lever through the J-...
  • Page 16 Rear 11. Put bolts through the four holes along the bottom edge of the Hght side panel. Put a Short lockwasher and hex nut on each bolt and tighten using a 7/16 inch wrench or socket. (Figure Note: It is sometimes difficult to get bolts through...
  • Page 17 Rear Fig. 40 - Truss Head Bolt Right Side Panel 22. Put a lockwasher and hex nut on the bolt and tighten using a 7/16 wrench or socket. 23. Repeat steps 20 - 22 with the left foot as- sembly. Shelf 24.
  • Page 18 sure that you attach the larger hole in each 31. Put the last two slide brackets in place on slide bracket to the rear support. Put a lock- each side of the front and rear supports. Make sure that the larger holes in the slide brackets washer and hex nut on each bolt and tighten are in line with the rear support.
  • Page 19 37. Tighten all screws, except those on the front and rear skirts, using a 7/16 inch wrench Drawer Front or socket. Drawer Putting Drawers Together The following parts are used to assemble drawers in model 113.198611: 10 inch Drawers ....6 inch Drawers ....
  • Page 20 4. Place the lower support under the shelf. It should rest directly below the under support, with the angled end sticking out. Line up the four holes in these three pieces. (Figure Note: The angled end of the lower support a useful way to tell the front of the cabinet from the back.
  • Page 21 10. Find the right and left side panels. Look 13. Put two truss head bolts through right side carefully to find the "R" and "L" stamped panel and spacer, one on each side. the metal near the center of the wide edge. 14.
  • Page 22 23. Use eight truss head bolts, lockwashers, Angled End Of Lower Support and hex nuts to hold the skirts in place. Hand- tighten. (Figure 24. Put a truss head bolt through the hole at the back, right corner of the shelf. This hole goes through the shelf and the right side...
  • Page 23 28. Put a lockwasher and hex nut on the bolt 37. Adjust the lower nut with the 9/16 inch wrench until the leveling foot is at the desired and tighten using a 7/16 inch wrench or sock- height. 38. Tighten the top nut by hand.
  • Page 24 Rear Skirt Front Skirt 1. Lay the two doors side by side. 2. Put a magnetic catch on the inside edge of each door. (Figure Doors Suppo_ Angled End Of Lower Support Fig. 58 44. Put two truss head bolts through the rear skirt and the upper...
  • Page 25 Mounting the Motor Both Models _lh WARNING: Plugging the saw in Fig. 63 - Pan Head Screw during assembly can result in electrical 5. Attach the doors to the hinges on the side shock or your fingers, hand, or arm being cut off from blade contact.
  • Page 26 13. Repeat steps 10-11 until the bevel lock 8. Slide the beve! encoder to the top center will not touch the left side of the yoke, and position so it will fit into the notch on the the gap is not more than 1/16 inch. motor support bracket.
  • Page 27 4. Reach through the top of the saw and use Attaching Trim Ledge and two screws to hold the trim cap in place. Trim Caps Tighten using a Phillips screwdriver. Both Models 5. Repeat steps 3-4 with the left trim cap. 1.
  • Page 28 Slide Button Eccentric Circle Eccentric Rail Circle Slide Square Hole Front Table - Upside Down Lock Handle With Fig. 76 Mounting Underneath Fig. 75 8. Push a slide button through the small hole in front of the eccentric circle on each table rail.
  • Page 29 U-Clips /U-Clip _Center Channe U-Clips Fig. 80 3. Slide one U-clip over the hole in the left side of the center channel as shown. (Figure Fig. 78 - Parts for Mounting Table 4. Put a washer on each of the mounting screws.
  • Page 30 7. Place the front table on the saw so that the Putting Drawers in Place mounting screws' line up with the U-clips. The front table should extend about one inch Model 113.198611 beyond the trim caps. 1. Slide each drawer in place on the slide 8.
  • Page 31 Location and Function of Controls 113.198611 113.198411 WARNING: The saw can start ac- On/Off Switch cidentally or be used by children others when the yellow key is left in the The on/off switch turns the power to the saw on and off. red switch.
  • Page 32 Bevel Lock The bevel lock is used to hold the blade at various angles to the table. To unlock bevel lock, move the lock to the right. Always hold the motor when you unlock the bevel lock. (Figure CAUTION: The motor is heavy and can swing down quickly.
  • Page 33 swivel lock when the motor is in one of these There are five pre-set bevel angles at -90 °, -45 °, 0°, 45 °, and 90 °. To unlock the bevel positions, stand facing the saw handle, pull lock when the blade is at one of these angles, the swivel lock all the way toward you, and turn the motor as you hold the lock in this move the bevel lock all the way to the right...
  • Page 34 Handwheel The handwheel controls the height of the radial arm. To raise the radial arm, turn the handwheel clockwise. To lower the radial arm, turn the handwheel counterclockwise. (Figure Fig. 95 - Handwheel One complete turn of the handwheel moves the arm 1/16 inch.
  • Page 35 Alignment of the Blade 1. Loosen the four screws in the front of the The blade of your radial arm saw must be aligned properly for two reasons: to make column support. (Figure cuts accurate, and to prevent binding of the blade and workpiece which can cause jams or thrown workpieces.
  • Page 36 1. Loosen the three leveling screws and be sure that the five mounting screws are snug but not overtightened. 2. Raise the radial arm until the bottom the motor is about 2-1/2 inches above the front table. 3. Unlock the bevel lock to release the motor. Hold onto the motor as you do this.
  • Page 37 8. Unlock the miter lock and swing the arm to 18. Move the arbor shaft over another point. the right until the arbor shaft is over the right Do not change the elevation of the arm. line. 19. Tighten the mounting screws and/or level- ing screws until the handle...
  • Page 38 3. Pull up on the fence. 4. If the fence is held firmly, no change needed. Go to the next section, If the fence is loose and can be pulled out of position, go to step 5. 5. Unlock the table locks. 6.
  • Page 39 _1_ CAUTION: Overtightening Squaring Crosscut Travel arbor nuts may cause the blade collars to warp and the blade to wobble while The blade must travel perpendicular to the cutting. Use the arbor wrenches fence along the radial arm in order for tighten the arbor nuts but do not over- crosscuts...
  • Page 40 If the blade tried to "walk" on the square, tighten the top left screw to move the arm to the right. Then tighten the top right screw to meet the column. Go to step 15. 15. Move the motor back and forth along the radial arm.
  • Page 41 If there is a gap between the square and the 23. Lock the rip lock, the spacer, fence and rear table back in place, lock the table the blade after any rotation (Figure 108), go locks, and go to the next section.
  • Page 42 9. Hold the motor tightly and lock the bevel 17. Turn the blade with your hand several lock. Do not let the motor move out of place. times and check to see if the square is flush with the blade. 10.
  • Page 43 4. Turn the blade with your hand several times and check to see if the square is flush with the blade. 5. If the square is flush with the blade after each rotation, no change is needed. (Figure 112) Go to the next section, If there is a gap between the square and the...
  • Page 44 4. Turn the blade with your hand several Squaring Blade to Table for times and check to see if the square is flush Ripping with the blade. 1. Unlock the swivel lock and turn the motor 5. If the square is flush with the blade after to the out-rip position...
  • Page 45 7. Hold the square in place and use the 9/16 hand. Try to keep the carriage bearing from inch wrench to turn the bolt until the square turning. is flush with the blade. 15. If you can keep either of the carriage bear- 8.
  • Page 46 Making Blade Parallel Table These steps are done to help prevent workpiece from being thrown or damaged when the saw is used for edging. Fig. 120 6. Lower the radial arm until the blade just rests on the edge of the framing square.
  • Page 47 9. Unlock the bevel lock. 16. Turn the blade with your hand several times and check to see if the square is flush 1(}. Loosen the two screws on the back of the with the blade. motor support using a 1/8 inch hex-I, wrench and pliers if necessary.
  • Page 48 _lk WARNING: Kickback can occur if 3. Make sure that the lower edge of the guard the spreader is not in line with the is parallel to the table. (Figure 125 - above) blade. You can be injured or killed. Al- ways adjust the spreader and make sure 4.
  • Page 49 13. Loosen both nuts on the spreader using a 1/2 inch wrench. Guard 14. Slide the spreader with your hand until it is against the fence directly behind the blade. 15. Tighten both nuts using a 1/2 inch Antikickback Pawls Spreader wrench.
  • Page 50 Digital Display ELEV: This button displays the height of the blade. The "0" display is usually set with the blade just touching the table. A positive dis- play shows the distance the blade has been _A/RS / CRI1 FT$1d RN raised above "0".
  • Page 51 5. If there is still no display, contact your Installing the Battery nearest Sears store, 1. Slide the batter), into the opening behind If the display says: the digital display with the angled corner top. (Figure 130) • go to step 6. Battery 6.
  • Page 52 6. Unlock the miter lock. 7. Move the arm to the right until it snaps into the 45 ° position. 8. Lock the miter lock. 9. The display should say: 10. Unlock the miter lock. 11. Move the arm to the left until it snaps into the -45°position.
  • Page 53 Bevel Encoder 14. If the display is correct at all three points, go to the next section, 1. Push the ON/OFF button to turn the dis- play on. If the display is not correct at one or more of these points, go to step 15.
  • Page 54 8. Push the ELEVbutton. 22. If the display is still not correct, repeat steps 15 - 21 until the bevel encoder is in the 9. Push the REF SET button. right position, 10. The display will say: If the display is correct, go to the next section.
  • Page 55 go to the next section, 8. Lock the rip lock. 9. Push the RIP button. If the display says: t Yi I-! I-! 10. If the display shows the O-RIP function, .,_ I I_l.l_l I_l go to step 11, or If the display shows the RIP function, push push the REF SET button again.
  • Page 56 Electrical Connections _I_WARNING: To avoid shock or fire, if Motor Specifications power cord is worn, cut, or damaged in any way have it replaced immediately. The AC motor used in this saw is a capacitor- start, non-reversible type having the following If your unit is for use on less than 150V it has specifications: a plug that looks like below.
  • Page 57 Extension Cords AnalWARNING: To maintain proper tool grounding, whenever the outlet you The use of any extension cord will cause are planning to use for this power tool some loss of power. Use the following table is of the two prong type do not remove to determine the minimum wire size or alter the grounding prong in any man-...
  • Page 58 Crosscutting Crosscutting is used to cut a workpiece length. The work_iece is held against the fence. The saw blade is pulled through workpiece. Cuts are usually made across the grain of the workpiece. Types of Crosscuts The basic types of crosscuts are shown below.
  • Page 59 4. Fingers or hand can slip into the saw Safety Information blade as you make a crosscut. Fingers, Crosscutting hand or arm can be cut off. Keep the hand holding the workpiece at least 8 in- Read and follow the safety information below ches to the side of the workpiece, out of...
  • Page 60 Blade Guard, Anti-Kickback 10. The workpiece cannot be controlled or held stable enough to do free hand Pawls and Spreader cutting. The workpiece can be thrown slip and pull fingers and hand into the The blade guard, anti-kickback pawls and saw blade.
  • Page 61 Cutting Table and Fence Crosscutting Checklist Kerfs Use the following checklist at the beginning You will need to cut a new table kerf (shal- of each new cutting period to reduce the risk low cut) and fence kerr (slot left in the fence of an accident.
  • Page 62 WARNING: The saw blade will sud- 8. Grasp saw handle and hold your forearm in line with the saw handle as shown below. denly come toward you when lowered into the table if the rip lock is unlocked. Fingers and hand can be cut off.
  • Page 63 4. Adjust the height of the anti-kickback Making Crosscuts pawls to clear top of fence and workpiece about 1/8 inch. The pawls and spreader help The following section contains safety informa- provide protection from the leading edge of tion and instructions for making crosscuts.
  • Page 64 12. Support and hold the workpiece down Pull blade through and against the fence firmly with your left workpiece to the distance shown below. hand. 13. Pull blade through fence and workpiece just enough to complete the cut. Fig 147. 14.
  • Page 65 Ripping When to Use In-Rip or Out-Rip Ripping is used to change the width of the workpiece by sawing along its length. The The in-rip saw position provides better workpiece is fed into the saw blade. visibility of both the workpiece and your fence is used as a guide.
  • Page 66 2. One of the most common and the Safety Information most dangerous mistakes people make Ripping is to reach for the workpiece at the out- feed side of the saw. DON'T t The Read and follow the safeb information below workpiece could kickback...
  • Page 67 2. The workpiece can be grabbed by the 4. Non-thru cuts increase the chance saw blade and take off like a missile. kickback because the anti-kickback Anyone standing in the path of the pawls cannot always grab the irregular workpiece can be killed.
  • Page 68 Rip Cutting Checklist Blade Guard, Anti-kickback Pawls and Spreader Use the following rip cutting checklist at the The blade guard, anti-kickback pawls and beginning of each new cutting period workpiece spreader are designed to reduce reduce the risk of an accident. eliminate the risk of injury from blade con- tact, workpiece...
  • Page 69 Blade Guard Adjustments Making a Rip Cut Table Kerf 1. Unplug saw and remove yellow key. You will need to make a table kerf before rip cut can be made. Eve n ' time you move 2. Put saw in In-Rip position and lock the the blade a new distance...
  • Page 70 Making Rip Cuts Anti-kickback Pawls and Spreader Adjust- ments When to Use In-Rip or Out-Rip !. Go to the outfeed end of the saw blade. The in-rip saw position provides better 2. Put edge of workpiece beside the blade visibility of both the workpiece and your and under...
  • Page 71 _IL WARNING: When making through 9. Stand out of the line of the workpiece be clear of workpiece in case of kickback. rip cuts do not set the blade closer than 1/2 inch from the fence or auxiliary fence, your hands will be brought close to the blade.
  • Page 72 on the arbor could cause the dado and arbor nut to spin off. Take several passes of the dado if cut required is greater than 13/16 of Kickback, Blade Contact. an inch wide. Fingers,hand or arm 3. To avoid excessive load on the motor can be cut off.
  • Page 73 3. Remove saw blade, dado, or other acces- _lb WARNING: If the auxiliary fence sory from the saw arbor shaft before using not used when the saw arm is in the 0° the accessory shaft. Do not use the saw with crosscut position, the molding head can-...
  • Page 74 Cutting Accessories Fences Push Stick Fences are required for all saw operations. Push sticks are used during ripping when the blade is placed between 2 and 6 inches from the fence. Crosscutting requires fences with kerfs (slots) to match the path of the saw, because the saw Make a push...
  • Page 75 Auxiliary Fence and Push Block An auxiliary fence must be used if the blade is positioned between 1/2 inch and 2 inches from the fence during ripping. An auxiliary 3/8" Plywood fence must always be used with a push block. Their purpose is to keep your hands away...
  • Page 76 5. Cut out a notch from the 12 inch side of Auxiliary Fence for Edging the 3/8 plywood that is 9 1/2 inches long by 3/8 inch wide. The dimensions of the remain- Make an auxiliary fence for edging: ing 3/8 plywood are shown in Fig.
  • Page 77 Featherboard Featherboards are used during rip cutting help keep the workpiece against the fence. The featherboard is clamped to the front table, so that the angled edge of the feather- board is against the workpiece on the infeed end of the blade. The other edge of the workpiece is against the fence.
  • Page 78 *Recommended Accessories Lower Retractable Guard Item Cat. No. Saw blades A lower retractable guard which meets (10" diameter with 5/8" hole) See Catalog OSHA requirements for occupational of the radial saw is available. (See Note) Caster 9-22254 lower guard is designed to provide Sanding Drum 9-25246...
  • Page 79 Glossary Anti-kickback Pawls: Pivoted objects with Molding Cut: Non-through cut which teeth which help prevent workpiece kickback. produces a contoured surface on the workpiece. Arbor: The bar or shaft that holds the saw blade. Outfeed: The end of the saw blade where the rip cut workpiece leaves the saw blade;...
  • Page 80 Helpful Hints 3. Place the same edge of the workpiece In order to get accurate cutting results from against the fence for all cuts. Make the your radial arm saw, do the following: first cut at one end of the workpiece, then flip the workpiece over and make 1.
  • Page 81 3. Lock the miter, bevel, or swivel lock. To extend the life of the front table of your saw, tack a piece of 1/4 inch plywood over it. Make sure that the tacks are not in the path These steps will reduce stress on saw parts, of the saw blade.
  • Page 82 Lubrication taining or lubricating your saw. Your saw is precision built and should When you receive your new Craftsman radial kept properly lubricated. Before describing saw, it requires no lubrication.
  • Page 83 • Lubricate the cam surfaces of the rip lock assembly. • A light film of oil should be wiped the face of the column tube to lubricate the fit between the column tube and column support. With elevation hand- wheel raise arm to upper limit.
  • Page 84 Swivel Lock Adjustments for Wear This handle provides a friction lock between Bevel Lock the upper face of the yoke and the bottom face of the carriage. It should eliminate The purpose of the bevel lock is to lock the play or rotation between these two parts when...
  • Page 85 Arm and Column With the miter lock unlocked and in the unin- dexed position the arm should fit snugly to the column tube and not allow any vertical movement. If you can move the end of the arm up and down an adjustment is needed.
  • Page 86 2. Push the carriage back against the rear stop. 3. Hold the front carriage bearing with your fingers as tight as possible and pull carriage forward at the same time. If you can prevent the bearing from turning an adjustment is re- quired.
  • Page 87 Rip Lock The HI) lock locks the carriage in any position along the length of the arm. If the carriage can be easily moved by pushing and pulling on the yoke handle when the rip lock is in the locked position an adjustment is required.
  • Page 88 3. As soon as the red button will click into Motor running position, the saw may be started operated normally. To avoid motor damage this motor should be blown out or vacuumed frequently to prevent 4. Frequent blowing of fuses or tripping of cir- sawdust buildup which will interfere...
  • Page 89 Changing Motor Voltage _11_DANGER: To avoid electric shock unplug the saw before changing motor voltage. Dual Voltage Switch Under normal home workshop usage, and if full voltage is supplied to the motor, your saw will operate efficiently on 120V, as connected at the factory.
  • Page 90 Troubleshooting _I_ WARNING: To avoid injury turn power switch off and remove plug from power source outlet before troubleshooting. Electronics Problem Probable Cause What to Do Battery not installed correctly. Adjust battery position in com- No display when On/Off button is pressed.
  • Page 91 Electronics What to Do Probable Cause Problem Arm or carriage moved Follow procedure for setting Display shows EEE.E EE.EE. rapidly for indicator to monitor, zero reference points in the Set- ting Electronic Display section. Have electronics checked by Encoder or indicator display Display will reset to zero defective.
  • Page 92 Motor - 2 What to Do Probable Cause Problem Reduce the line load. Power line overloaded with Motor fails to develop full lights, appliances, and other power. motors. (Power output of motor decreases rapidly with Increase wire sizes, or reduce Undersize wires or circuit too decrease...
  • Page 93 Saw Operations Problem Probable Cause What to Do Crosscuts not accurate Looseness between column tube to Alignment of the Blade, 0° and 45 ° miter. and column support. Adjusting Elevation. Crosscut travel not square Go to Alignment of the Blade, with fence.
  • Page 94 Saw Operations What to Do Problem Probable Cause Go to Alignment of the Blade, blade not square Workpiece kerr rough with tooth marks from to fence. Squaring Blade to Fence. blade (also called heel). Go to Alignment of the Blade, Saw blade not parallel to table.
  • Page 95 Saw Operations - 3 Problem Probable Cause What to Do Clamping force not suffi- Bevel lock needs adjusting. Go to Maintaining Your Saw, cient at bevel angles other Adjustments for Wear, Bevel than 45 °. Lock. Depth of cut varies from Table not parallel...
  • Page 96 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113,198611 ISEE FIG. ]_12 18_,,,_ (SEE FIGS} (SEE FIG, (SEE FIG. 3& ISEE FIG. 37 45 ptt42 Figure 1...
  • Page 97 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 Always order by Part Number - Not by Key Number FIGURE Part Part Description Description 815980 STD601103 *Screw, Pan Rec. Bushing 60208 Nut, Push Type T 10-32 x 3/8...
  • Page 98 PARTS LIST CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113,198611 Figure...
  • Page 99 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 Always order by Part Number - Not by Key Number FIGURE 2 - BASE AND COLUMN ASSEMBLY Part Part Description Description STD511105 Screw, Hex Washer Hd. *Screw, Pan Hd. 10-32 x 1/2...
  • Page 100 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 • BEVEL ENCODER CORD MOTOR CORD Figure 3...
  • Page 101 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 Always order by Part Number - Not by Key Number FIGURE 3 - YOKE AND MOTOR ASSEMBLY Part Part Description Description 815803 808380-2 Screw, Pan Hd., Cap, Motor Support Plastite No.
  • Page 102 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 Figure...
  • Page 103 PARTS LIST CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 Always order by Part Number - Not by Key Number FIGURE 4 - YOKE ASSEMBLY Part Part Description Description *Lockwasher, External 5/16 810214-3 Screw, Low Hd. STD551131 815691 Cap 5/16-18 x 7/8...
  • Page 104 PARTS LIST CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 Figure...
  • Page 105 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 Always order by Part Number - Not by Key Number FIGURE 5 - ARM ASSEMBLY Part Part Description Description 816490 815688 Encoder, Rip Arm, Radial 815809 Cable (Includes Key #20 &...
  • Page 106 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS, 113.198411 and 113.198611 Always order by Part Number - Not by Key Number FIGURE 6 - TABLE ASSEMBLY Part Description 815757 Table, Rear 815755 Table Spacer 815758 Fence, Rip 817102 Table, Front...
  • Page 107 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 Always order by Part Number - Not by Key Number FIGURE 7 - FOOT ASSEMBLY - MODEL 113.198611 Part Description STD601103 *Screw, Pan Rec. Hd. Type T 10-32 x 3/8...
  • Page 108 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 • Figure...
  • Page 109 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 Always order by Part Number - Not by Key Number FIGURE 8 - CABINET ASSEMBLY FOR MODEL 113.198611 Part Part Description Description 805589-5 Screw, Truss Hd. 1/4-20 x 1/2...
  • Page 110 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 Figure...
  • Page 111 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 Always order by Part Number - Not by Key Number FIGURE 9 - CABINET ASSEMBLY MODEL 113.198411 Part Part Description Description 805589-5 803835-1 Screw, Truss Hd. 1/4-20 x 1/2...
  • Page 112 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 Always order by Part Number - Not by Key Number FIGURE 10 - DRAWER ASSEMBLIES 3", 6", 10" Part Description 815912 Drawer Assembly, 3" 815917 Drawer Assembly, 6"...
  • Page 113 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 Always order by Part Number - Not by Key Number FIGURE 11 - MOTOR ASSEMBLY Part Description 507745 Housing, Motor STD376116 *Capacitor 64950 Screw, Type "T" 64951 Screw, Flat Head...
  • Page 114 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.198411 and 113.198611 Always order by Part Number - Not by Key Number FIGURE 12 - GUARD ASSEMBLY p:rt Part Description Description 816264-1 Guard STD581050 *Ring, Retaining 63270 120399 Spreader *Nut, Square 5/16-18...
  • Page 115 NOTES...
  • Page 116 NOTES...
  • Page 117 NOTES...
  • Page 118 NOTES...
  • Page 119 NOTES...
  • Page 120 /"- SEA/R,. 10-INCH DELUXE ELECTRONIC Operators RADIAL SAW Manual SERVICE Now that you have purchased your 10-inch electronic radial saw, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts when you call or visit.

This manual is also suitable for:

113.198611

Table of Contents