Snap-On 870011 Instruction Manual
  1. Manuals
  2. Brands
  3. Snap-On Manuals
  4. Nail Gun
  5. 870011
  6. Instruction manual
Snap-On 870011 Instruction Manual

Snap-On 870011 Instruction Manual

Clipped head framing nailer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Enlarged version
FOR CUSTOMER SERVICE
PARA EL SERVICIO
PARA EL CONSUMIDOR
1-888-278-8092
Printed in Taiwan
®
®
SNAP-ON
IS A TRADEMARK LICENSED BY SNAP-ON
CORP.,
U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
©COPYRIGHT 2007 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
870011 – Clipped Head Air Nailer _Rev 10/4/07
CLIPPED HEAD FRAMING NAILER

INSTRUCTION MANUAL

THIS
MANUAL
CONTAINS
IMPORTANT
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO SO
COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR SNAP-ON
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE
DEPARTMENT AT 1-888-278-8092. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION.
MODEL #870011
INFORMATION
REGARDING
SAFETY, OPERATION,

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 870011 and is the answer not in the manual?

Questions and answers

Related Manuals for Snap-On 870011

Summary of Contents for Snap-On 870011

  • Page 1: Instruction Manual

    DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE PARA EL CONSUMIDOR DIRECTED TO: IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR SNAP-ON ©COPYRIGHT 2007 ALLTRADE TOOLS, LLC. PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS CONGRATULATIONS! Thanks for choosing this product. Our aim is to provide you with the highest quality prod- CONGRATULATIONS! ......... 2 ucts, and we want you to be totally satisfied with your product and our Customer Service.

  • Page 3: Important Information About This Manual

    IMPORTANT INFORMATION ABOUT THIS MANUAL CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, Improper maintenance and operation are responsible for the majority of accidents if not avoided, may result in property damage. involving clipped head nailers. The largest portion of these could be prevented by recognizing the basic safety rules and precautions.
  • Page 4 Always use hearing protection to protect your ears against Do not connect clipped head nailer to an air source capable of hearing loss due to exhaust noise. Always wear proper safe- generating more than 200 psi (14.06 kg/cm G). Over-pressurizing ty glasses to prevent injuries to the eyes from fragments of the clipped head nailer will result in bursting, abnormal operation or the work piece, defective nails or other debris caused by using the clipped...

  • Page 5: Functional Description

    COMPONENT INSTALLATION Thoroughly clean and maintain the clipped head nailer after every use. Lubricate moving parts to prevent rust and minimize friction-related wear. Wipe Never use a non-relieving air coupler with the clipped down the entire tool and remove all dust from the moving parts. Properly store head nailer.

  • Page 6: Operating The Clipped Head Nailer

    To improve the connection between the quick disconnect and air nailer, and to help OPERATION IN SINGLE SEQUENTIAL ACTUATION MODE prevent oxidation, apply PTFE tape or joint compound to the connector threads To select the Single Sequential Actuation Mode (see before insertion.

  • Page 7: Adjusting Depth Of Nailing

    To select Contact Sequential Actuation Mode (see Figure 2): 1. Press and hold Actuation Selector embedded in the Always disconnect the clipped head nailer before mak- trigger. ing any adjustments to the nail depth setting. 2. Rotate Actuation Selector up to the Contact USING THE HOOK Sequential Actuation (TTT).

  • Page 8: Using The No-Mar Nosepiece

    6. Select Single Sequential Actuation Operation. Check for leaks. Without pulling USING THE NO-MAR NOSEPIECE the trigger, press the work piece contact against the work piece. The tool MUST NOT operate. Holding the tool away from the work piece, pull trigger Always disconnect the air hose before attaching the and hold for 5 seconds.

  • Page 9: Locking And Unlocking The Trigger

    CLEARING JAMS DO NOT hold the trigger in a half-pulled position. This Typically, jams are caused when a fastener or a fastener fragment becomes wedged could cause an unexpected nailing to occur if the work piece contact is permit- between the driver blade and nail guide. Using the wrong fastener can also cause jams. ted to re-contact the work piece.

  • Page 10: Mandatory Maintenance

    Always visually inspect clipped head nailer before every use. Check on the overall MANDATORY MAINTENANCE condition and for any loose screws. Tighten any screws that have come loose. See Figure 11. All maintenance and repairs should be performed by an Visually inspect the work piece contact and authorized repair facility.

  • Page 11: Parts Diagram

    PROBLEM POSSIBLE CAUSE SOLUTION PARTS DIAGRAM Increase air pressure, Ensure proper air pres- sure is being used. Do not exceed 120 psig (8.3 bars, 8.5 kg/cm Weak drive. Slow to Inspect for worn driver cycle between nailings. blade. Inspect piston O-ring for Contact Customer wear or damage.

  • Page 12: Parts List

    PARTS DIAGRAM PARTS LIST ITEM NO. PART NO. DESCRIPTION K0300-4011 Top Cap Set A0000-0421 Nylon Screw M6*18 A0005-1071 Washer A0304-0521 Exhaust Cover A0000-0171 Screw M6*30 A0005-0541 Washer 12.5*1.6T A0200-0811 O-Ring 11.8*1.5 A0203-0111 Muffler K0300-4021 Top Cap & Screw Set A0003-0331 Screw A0301-1641 Cap, Top...
  • Page 13 ITEM NO. PART NO. DESCRIPTION ITEM NO. PART NO. DESCRIPTION A0401-2031 Body A0200-3221 O-Ring 58*2.5 A0004-0021 Nylon Nut M5 A0200-1952 O-Ring 57.5*3.3 K0500-1501 Trigger Set A0303-0811 Cylinder A0011-0201 Spring Pin 3*30 A0800-0781 Spacer A0009-0011 Steel Ball A0200-2002 O-Ring 85*3.5 A0100-1961 Spring A0311-0351 Sleeve Hold Down...

  • Page 14: Specifications

    Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail A0000-0061 Screw M5*12 purchaser of the accompanying SNAP-ON™ portable air tool and no one else all K0700-4741 Magazine Set parts of the product (except those parts referred to below which are specifically...
  • Page 15 EVENT, WHETHER BECAUSE OF A BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL ALLTRADE'S AND/OR ITS The use of other than genuine Snap-On™ Repair Parts will VOID the warranty. REPRESENTATIVE (S) LIABILITY EXCEED THE PRICE OF THE PRODUCT. All LIA-...

Table of Contents