Hitachi SJ300 Series Replacement Manual page 19

26 Acceleration time setting 1
Acceleration time setting 2
27 Second acceleration time setting
28 Acceleration curve selection
29 Acceleration curve constants setting
30 Deceleration time setting 1
Deceleration time setting 2
31 Second deceleration time setting
32 Deceleration curve selection
33 Deceleration curve constants setting
34 Acceleration stop frequency setting
35 Acceleration stop time setting
36 Operation mode selection
37 Resume on free-run stop cancellation mode
38 Multi-speed frequency setting 1
39 Multi-speed frequency setting 2
40 Multi-speed frequency setting 3
41 Multi-speed frequency setting 4
Multi-speed frequency setting 7
42 DC braking enable
43 DC braking / edge or level detection
44 DC braking frequency setting
45 DC braking force for starting
46 DC braking force during deceleration
47 DC braking time for starting
48 DC braking time during deceleration
49 DC braking wait time
50 Dynamic braking usage ratio
51 Electronic thermal characteristic 1
Electronic thermal characteristic 2
52 Level of electronic thermal setting 1
Level of electronic thermal setting 2
53 Free setting, electronic thermal current 1
54 Free setting, electronic thermal frequency 1
55 Free setting, electronic thermal current 2
56 Free setting, electronic thermal frequency 2
57 Free setting, electronic thermal current 3
58 Free setting, electronic thermal frequency 3
59 Overload restriction setting
60 Overload restriction constant setting
61 Overload restriction, enable for acceleration
No. Name
setting
Digital
Remote Operator
operator
F6 F-06 ACC1 30.0
F6 ACC1 30.0
F6 ACC2 15.0
- ACC LINE L
- ACC GAIN 02
F7 F-07 DEC1 30.0
F7 DEC1 30.0
F7 DEC2 15.0
- DEC LINE L
- DEC GAIN 02
- F-08 FSP F 0.0Hz
- FSP TIME 0.0s
A59 F-10 RUN MODO NOR
A54 RUN FRS ZST
A12 F-11 SPD 1 0.00
A13 SPD 2 0.00
A14 SPD 3 0.00
F2 SPD 4 0.00
F2 SPD 7 0.00
- F-20 DCB SW OFF
- DCB KIND LVL
- DCB F 0.5Hz
- DCB V-STA 00
- DCB V-STP 00
- DCB V-STA 0.0s
- DCB V-STP 0.0s
- DCB STOP-T 0.00s
A38 F-21 BRD-%ED 1.5%
A24 F-23 E-THM CHAR SUB
A24 E-THM CHAR SUB
A23 E-THM LEVEL 100%
A23 E-THM LEVEL 100%
- E-THM A1 Factory set
- E-THM F1 Factory set
- E-THM A2 Factory set
- E-THM F2 Factory set
- E-THM A3 Factory set
- E-THM F3 Factory set
- F-24 OLOAD LEVEL 125%
- OLOAD CONST 1.0
- OLOAD ACC ON
J300
Function code Default
20/24
code
(Digital
operator)
F002 30.00
F202 30.00
Second acceleration time (A292) can be also set in the case
A092 15.00
of the SJ300.
A097 00
A131 02
F003 30.00
F203 30.00
Second deceleration time (A293) can be also set in the case
A093 15.00
of the SJ300.
A098 00
A132 02
A069 0.00
A070 0.0
A085 00
b088 00
A021 0.00
A022 0.00
A023 0.00
A024 0.00
0.00
A051 00
A056 01
A052 0.50
A057 0. DC braking carrier frequency (A059) can be also set in the
case of the SJ300.
A054 0.
A058 0.0
A055 0.0
A053 0.0
SJ300 have dynamic braking control (b095) and dynamic
b090 0.0
braking activation level setting (b096).
b013 00
Can be set up to 3
b213 00
b012 Rated current
Can be set up to 3
b212 Rated current
b016 0.0
b015 0.
b018 0.0
b017 0.
b020 0.0
b019 0.
b022 Rated current x1.5 Two sets of overload restriction parameter settings and
values are available in the case of the SJ300. (b025, b026,
b023 1.00
b024) Selection can be made by OLR function assigned to an
b021 01
intelligent input terminal.
SJ300
Function Default setting
rd
motor (b313) in the case of the SJ300.
rd
motor (b312) in the case of the SJ300.
Remarks