Related Manuals for Elektra Beckum 4 DN
Summary of Contents for Elektra Beckum 4 DN
- Page 1 Betriebsanleitung Systemkreissäge Operating Instruction System circular saw Instructions d'utilisation Scie circuaire à système PK 255...
-
Page 2: Great Britain
Deutschland Great Britain France Die beiliegende Garantiekarte senden Sie bitte an uns zurück. Den Kaufbeleg bitte aufbewahren! Ein Anspruch auf Garantieleistungen besteht nur gegen Vorlage des Kaufbelegs. Die Adresse Ihrer nächstgelegenen Werksvertretung finden Sie auf der hinteren Umschlagseite. Please return the enclosed warranty card to us. Retain proof of purchase! You are only entitled to claim warranty against proof of purchase. -
Page 3: Scope Of Delivery
Scope of delivery System circular saw with saw blade Blade guard hardware bag Rip fence with auxiliary fence extrusion Push stick / feeding aid Leg with foot (4x) Connector suction hose / chip case PK 255... -
Page 4: Saw Components And Controls
Saw components and controls Saw blade Riving knife Blade guard Rip fence with auxiliary fence extrusion Push stick / feeding aid Handwheel with lock lever for blade tilt setting Handwheel for depth of cut setting On/off switch with emergency stop... -
Page 5: Please Read First
- electric shock as little as possible. Please note in particular: A circular saw is a dangerous tool which can, due to operator carelessness, cause serious personal injury. It is therefore recommended you follow the safety information given below, and know and follow the legal regulations pertaining to the operation of circular saws. -
Page 6: Symbols Shown On The Machine
Max. depth of cut Safety devices Riving knife The riving knife prevents the workpiece from being caught by the rising teeth of the saw blade and being thrown against the operator. Always have riving knife installed during operation. distance Blade guard... -
Page 7: Operating Controls
Handwheel for blade tilt setting The saw blade can be tilted steplessly between 0° and 45°. The centre of motion is at saw table level, so the depth of cut remains the same, regardless of the bevel angle. PK 255... -
Page 8: Assembly And Connection
Mitre fence The mitre fence can be fitted into groove of either the sliding carriage or the saw table. It is locked in the groove with the ratchet lock lever (black arrow). For mitre cuts the fence extrusion turns through 45˚... - Page 9 Dust collection from chip casing 1. Turn saw upside down. 2. Remove transport support inside the saw hous- ing. 3. Attach suction port to chipcase with - 3 ea. hex. head screw M 6x13 - 3 ea. washer - 3 ea. serrated lock washer - 3 ea.
-
Page 10: Mains Connection
1. After the saw is assembled, with all guards and safety devices operational, connect it to the power supply. 2. Raise saw blade fully. -
Page 11: Rip Cuts With Rip Fence
Rip cuts with rip fence 1. Lock rip fence in required position on saw table. Danger! Use push stick if distance between rip fence and saw blade is less than 120 mm. 2. Reposition auxiliary fence extrusion if neces- sary: - Low edge (as shown) = for sawing thin stock;... -
Page 12: Saw Blade Adjustment
6. To block the saw blade insert lock bar into hole in the saw table and turn saw blade by hand until lock bar engages in saw spindle hole. 7. Loosen saw blade spindle arbor nut with span- ner (L.H. thread!). -
Page 13: Drive Belt Tensioning
7. Stand saw back on its feet/workstand. 8. Adjust saw blade position by turning the setting nuts. 9. Turn saw over again and place on its saw table. 10. Tighten both nuts inside the saw again. 11. Stand saw on its feet/workstand again. -
Page 14: Blade Tilt Stop Setting
3. Adjust backstop setting screws on both front and rear of the saw until blade is in exact 0˚ posi- tion when set against the 0˚ stop. 4. To check the setting of the 45˚ backstop, repeat steps 1 to 3 accordingly. - Page 15 Universal fence adjustments 1. Check if fence is square against saw blade with a try square. 2. If necessary, loosen fixing screws and adjust mitre scale. 3. Retighten fixing screws. Cleaning the saw 1. Lay machine on its side. 2. Remove chips and saw dust with vacuum...
-
Page 16: Troubleshooting
Before carrying out any fault service or main- tenance work always: - Switch machine OFF. - Unplug power cable. - Wait for saw blade to come to standstill. Check that all safety devices are operational again after each fault service. Motor does not run Undervoltage relay Switch on again. -
Page 17: Technical Specifications
Sound pressure level AL Sound power level A L Available saw blades Application Saw blade with extraordinary long edge life for - solid timber - lamited timber Saw blade for smooth edge cuts in - solid timber... - Page 18 Circuit diagrams Single-phase motor Three-phase motor 2.16 PK 255...
- Page 19 Aktiengesellschaft Postfach 13 52, D-49703 Meppen EG-Konformitätserklärung - EC conformity declaration - Déclaration de conformité CEE EG-verklaring van overeenstemming - EF-overensstemmelsesattest - EG-konformitetsdeklaration EF-konformitetserklæring - Selvitys ey-standardinmukaisuudesta - Dichiarazione di conformità CE Declaración de conformidad-UE - Declaração de conformidade CE Wir erklären, daß...
- Page 20 Belgium Elektra Beckum Belgium N.V.S.A. Industriezone Hofte te Bollebeeklaan B-1730 Asse-Mollem Tel.: 0032-24540454 Fax: 0032-24540450 Deutschland Elektra Beckum AG Daimlerstraße 1 D-49716 Meppen Tel.: 01803-333 456 Fax: 01803-333 457 Danmark Elektra Beckum Danmark Lundeborgvej 9 Postbox 8113 DK-9220 Aalborg OE Tel.: 0045-98-151300...
Need help?
Do you have a question about the 4 DN and is the answer not in the manual?
Questions and answers