Galaxy DX 44V Owner's Manual

Galaxy DX 44V Owner's Manual

Full channel am/fm mobile transceiver

Advertisement

WARRANTY
This radio is covered by a two
year limited parts and labor
warranty.
"Limited" means that we will repair problems caused by factory defects or normal use
at no charge.
Before returning a radio to us for warranty service, please call our Service Department
for a Repair Authorization Number (RAN). This RAN must be written below your
return address on the outside of the shipping box. Boxes, which arrive without a RAN,
will be refused, and the shipping company will return the unopened box to you. Be sure
to have a pen and paper ready along with the serial number of your radio before calling.
We will give you the RAN and our shipping address over the phone. The telephone
number of the Service Department is (760) 480-8800, and we suggest calling between
10:00 AM and 4:00 PM Pacific Time.
Please include a note with a detailed description of the symptoms. This is important
because it will help the technician who works on your radio to locate your problem.
Intermittent problems are easily overlooked, so be sure to give as much detail as
possible in your note. Also, please include your telephone number in case our
technicians have any additional questions.
Do not send your power cord or microphone unless we ask for these items during our
telephone conversation.
You are responsible for getting the radio safely to us. (We suggest using United Parcel
Service.) You must pay to ship the radio to us, and we will pay to ship the radio back to
you. Since we use UPS and they do not ship to Post Offices boxes, please provide us
with a street address for the return of your radio.
We will repair and return your radio as soon as we can. We appreciate your choosing a
Galaxy radio and we want you to be on the air as much as possible!
Be sure to visit our web site at
www.GalaxyRadios.com
Full Channel AM/FM Mobile Transceiver
Printed In Malaysia
AT3602014D
PD000808
DX−44V
OWNER'S MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DX 44V and is the answer not in the manual?

Questions and answers

Summary of Contents for Galaxy DX 44V

  • Page 1 We will repair and return your radio as soon as we can. We appreciate your choosing a Full Channel AM/FM Mobile Transceiver Galaxy radio and we want you to be on the air as much as possible! Be sure to visit our web site at www.GalaxyRadios.com...
  • Page 2: Specifications

    TABLE OF CONTENTS Specifications Page GENERAL Specification ........Frequency Range 28.315 to 28.755 MHz Frequency Control...
  • Page 3: Installation

    Installation RECEIVER LOCATION Sensitivity AM: 0.5 µV for 10 dB (S+N)/N at greater than Plan the location of the transceiver and microphone bracket before starting the ½ -watt of audio output. installation. Select a location that is convenient for operation and does not interfere FM: 1.0 µV for 20 dB (S+N)/N at greater than with the driver or passengers in the vehicles.
  • Page 4: Ignition Noise Interference

    IGNITION NOISE INTERFERENCE TUNNING THE ANTENNA FOR OPTIMUM SWR Use of a mobile receiver at low signal levels is normally limited by the Since there is such a wide variety of base and mobile antennas, this presence of electrical noise. The primary source of noise in automobile installations section will strictly concern itself to the various types of mobile adjustable is from the generator and ignition system in the vehicle.
  • Page 5: Operation

    D. Try a different location on your car (keeping in mind the radiation pattern Operation you wish) E. Is the antenna perfectly vertical? CONTROL FUNCTIONS F. Try a different location in your neighborhood. Stay away from large There are thirteen controls and three indicators on the front panel of your metal objects when adjusting (metal telephone or light posts, fences, etc.).
  • Page 6: Rear Panel

    5. MODE (PA/FM/AM) SWITCH. This switch is used to select PA, FM, AM mode of operation. The AM or FM mode is normally, but when you set to PA 16. CHANNEL INDICATOR. Numbered LED indicates the selected channel position, the transceiver acts as a public address amplifier. Before operating you wish to operate on.
  • Page 7: Press-To-Talk Microphone

    PRESS-TO-TALK MICROPHONE ALTERNATE MICROPHONES AND INSTALLATION The receiver and transmitter are controlled by the press-to-talk switch on the For best results, the user should select a low-impedance dynamic type microphone. Press the switch and the transmitter is activated, release switch to microphone or a transistorized microphone.
  • Page 8 Fig. 3 Microphone plug pin numbers viewed from rear of pin receptacle. Be sure that the housing and the knurled ring of Fig. 2 are pushed back onto the microphone cable before starting to solder. If the washer is not captive to the pin receptacle body, make sure that it is placed on the threaded portion of the pin receptacle body before soldering.

Table of Contents

Save PDF