Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Antec One
Summary of Contents for Antec One
- Page 1 User One / One S / Manual One S3...
- Page 2 ATX specification compliance, broad compatibility, and power savings capability. At Antec, we continually refine and improve our products to ensure the highest quality. As such, your new chassis may differ slightly from the description in this manual due to improvements applied for the optimal building experience.
-
Page 3: Table Of Contents
Table of Contents Section 1: Introduction Getting to Know Your Chassis ................5 Chassis Specifications..................6 Included Screws ....................7 Section 2: Hardware Installation Setting Up ......................9 Removing the Side Panels and Front Bezel…………………………………………………… . 9 Motherboard Installation................... 10 Installing KUHLER H O Liquid Coolers .............. -
Page 4: Section 1: Introduction
Section 1 Introduction One / One S / One S3 User Manual... -
Page 5: Getting To Know Your Chassis
Getting to Know Your Chassis One S / One S3 1. 3 x 5.25” drive bays 2. 5 x 3.5” drive bays 3. 2 x 2.5” drive bays 4. 1 x 120 mm top exhaust fan (standard) 5. 1 x 120 mm rear exhaust fan (standard) 6. -
Page 6: Chassis Specifications
Chassis Specifications Chassis Type Mid Tower Chassis Color Black Dimensions 17.2” (H) x 8.2” (W) x 19.2” (D) 438 mm (H) x 208 mm (W) x 488 mm (D) Weight One: 10.8 lbs / 4.9 kg One S / One S3: 10.4 lbs / 4.7 kg Cooling One: - 1 x 120 mm top exhaust fan... -
Page 8: Section 2: Hardware Installation
Section 2 Hardware Installation One / One S / One S3 User Manual... -
Page 9: Setting Up
Setting Up When working in your case, please keep the following in mind: Put the case upright on a flat, stable surface so that the rear panel (power supply and expansion slots) is facing you. Handle all components and cards with care. ... -
Page 10: Motherboard Installation
Motherboard Installation Before proceeding, check the manual for your CPU cooler to find out if there are steps you must do before installing the motherboard. Make sure you have the correct I/O panel for your motherboard. If the panel provided with the chassis isn’t suitable, please contact your motherboard manufacturer for the correct I/O panel. -
Page 11: Installing Kuhler H O Liquid Coolers
Installing KUHLER H O Liquid Coolers The following instructs how to install the Antec KUHLER H O liquid CPU cooler (620 / 920). For any other CPU coolers, please consult your manufacturer’s installation guide. Caution: Check your motherboard’s CPU socket to ensure its compatibility with the KUHLER H O. -
Page 12: External 5.25" Device Installation
External 5.25” Device Installation The One / One S / One S3 can support up to three 5.25” devices. 1. Remove the side panels and front bezel as directed in Section 2.2. 2. Remove the drive bay cover by pressing out on the two small tabs on either side of the cover, then pushing the cover into the front of the bezel. -
Page 13: Internal 2.5" Device Installation
Internal 2.5” Device Installation There are two 2.5” drive mounting locations in the One / One S / One S3: at the base of the drive cage and a dedicated mount in the middle of the drive cage. To install at the base of the drive cage: 1. -
Page 14: Internal 3.5" Device Installation
Internal 3.5” Device Installation The One / One S / One S3 includes 5 pairs of 3.5” drive rails. You will need 1 pair per 3.5” drive. 1. Line up the drive rail pins to the sides of your 3.5” drive. -
Page 15: Section 3: Front I/O Ports
Section 3 Front I/O Ports One / One S / One S3 User Manual... -
Page 16: Usb 3.0
USB Ports One / One S3: The One and One S3 come with two front panel USB 3.0 ports and includes an internal motherboard connector. Connect these in the same way you would a standard front panel with an internal header connector. One S: The One S comes with two front panel USB 2.0 ports. -
Page 17: Power Switch / Reset Switch / Hard Disk Drive Led Connectors
Power Switch / Reset Switch / Hard Disk Drive LED Connectors Connected to your front panel are LED leads for power and HDD activity, as well as switch leads for the power and reset buttons. Attach these to the corresponding connectors on your motherboard. Consult your motherboard manual for specific pin header locations. -
Page 18: Rewiring Motherboard Header Connections
Rewiring Motherboard Header Connections There may come a time when you need to reconfigure the pin-out of a motherboard header connector. Examples could be for your USB header, audio input header, or some other front panel connector such as the Power Button connector. Before performing any work, please refer to your motherboard user’s manual or your motherboard manufacturer's website to confirm the pin-out needed for your connector. -
Page 19: Section 4: Cooling System
Section 4 Cooling System One / One S / One S3 User Manual... -
Page 20: Included Fans
Included Fans One: The One comes with two standard fans (yellow outline) – a rear 120 mm exhaust fan and a top 120 mm exhaust fan. The red rectangles indicate additional fan mounts. Mounting procedures for these fans is discussed in Section 4.2. -
Page 21: Optional Fans
Optional Fans One: The One includes mounts for up to three more fans. These mounts are as follows: 1 x front intake 120 mm mount 1 x side 120 mm mount 1 x bottom 120/140 mm mount One S / One S3: The One S / One S3 includes mounts for up to four more fans. These mounts are as follows: 1 x front intake 120 mm mount 1 x side 120 mm mount... -
Page 22: Air Filters
Bottom 120/140 mm fan At the base of the case, there is a fan mount that can fit either a 120 mm or 140 mm fan for additional air intake. 1. Remove the left side panel as outlined in Section 2.2. - Page 23 +31 (0) 10 437-1752 Technical Support US &Canada 1-800-22ANTEC nasupport@antec.com Europe +49-40 226139-42 easupport@antec.com www.antec.com © Copyright 2012 Antec, Inc. All rights reserved. All trademarks are the property of their respective owners. Reproduction in whole or in part without written permission is prohibited.
Need help?
Do you have a question about the One and is the answer not in the manual?
Questions and answers