Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for HP Omni 27-1100
Summary of Contents for HP Omni 27-1100
- Page 2 The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
-
Page 3: Table Of Contents
Table of contents 1 Preparing the computer for wall-mounting ............... 1 What you need ........................1 Safety information ........................1 Preparing to remove the computer stand ..................2 Removing the computer stand ....................2 2 Reinstalling the stand on the computer ................9 What you need ........................ -
Page 5: Preparing The Computer For Wall-Mounting
Preparing the computer for wall- mounting This document provides instructions for preparing your HP All-in-One computer for wall-mounting. The VESA mounting bracket is attached to the back of the computer. This bracket attaches to a wall- mounting device (sold separately). You need to remove the computer stand before wall-mounting the computer. -
Page 6: Preparing To Remove The Computer Stand
WARNING! Please read “Additional Safety Information” in the Limited Warranty and Support Guide before installing and connecting your system to the electrical power system. Preparing to remove the computer stand To avoid injury and equipment damage when opening the computer, always complete the following steps in order: Remove any media and external devices (such as any CD, DVD, memory cards, USB devices, or external hard disk drives) from the computer. - Page 7 NOTE: Save the VESA cover, the computer stand, and the six screws, so that you can convert the computer back to a desktop unit in the future. To reinstall the stand, follow all the steps in Reinstalling the stand on the computer on page Place the computer facedown on a stable, flat surface that is covered with a soft cloth.
- Page 8 Loosen the two screws at the bottom that secure the back cover to the computer. Keep turning the screwdriver until you hear five clicks. These clicks indicate that the screw is sufficiently loosened. Do not attempt to remove the screw from the hole. If present, loosen the screw (1) at the center of the back cover.
- Page 9 Remove the six screws that attach the stand to the computer. There are three screws each at the bottom left and right of the computer. Save the screws. Lift the stand slightly (1) and then disengage it from the hook on the left side (2). Remove the stand from the computer.
- Page 10 Remove the ring covers (1,2) from the lower center back of the computer. Snap the ring covers into place on the lower corners of the computer. Chapter 1 Preparing the computer for wall-mounting...
- Page 11 To replace the back cover, align the side and rear I/O openings on the back cover with the corresponding connectors on the computer. Press the cover so it snaps into place, and ensure that there are no gaps between the computer and the cover. Tighten the two screws at the bottom of the computer to secure the back cover to the computer.
- Page 12 Attach the wall-mounting hardware (purchased separately) according to the manufacturer's instructions to the back of the computer, using the 100 mm x 100 mm (3.9 in. x 3.9 in.) screw holes. CAUTION: The computer is heavy and might require two people to mount it to the wall. Chapter 1 Preparing the computer for wall-mounting...
-
Page 13: Reinstalling The Stand On The Computer
Reinstalling the stand on the computer To convert the computer from a wall-mounted unit to a desktop unit, reinstall the computer stand on to the computer. What you need A stable, flat surface to place the computer ● A soft, clean cloth (such as a clean, large towel) to protect the computer when you place it face ●... -
Page 14: Removing The Wall-Mounting Hardware
Removing the wall-mounting hardware To prepare to remove the wall-mounting device, follow these steps in order: Remove any media and external devices (such as any CD, DVD, memory cards, USB devices, or external hard disk drives) from the computer. CAUTION: Static electricity can damage the electronic components of the computer or optional equipment. -
Page 15: Replacing The Computer Stand
Replacing the computer stand To replace the computer stand, perform the following steps: Loosen the two screws at the bottom that secure the back cover to the computer. Keep turning the screwdriver until you hear five clicks. These clicks indicate that the screw is sufficiently loosened. If present, loosen the screw (1) at the center of the back cover. - Page 16 Remove the ring covers from the left and right side of the computer. Place the ring covers (1,2) back into their storage location at the center back of the computer. Chapter 2 Reinstalling the stand on the computer...
- Page 17 Engage the hook at the lower left on the computer with the slot on the stand (1), and place the stand back on the computer (2), aligning the screw holes on the stand with the screw holes on the computer. Install the three screws on both the left and right side to secure the stand to the computer.
- Page 18 To replace the back cover, align the side and rear I/O openings on the back cover with the corresponding connectors on the computer. Press the cover so it snaps into place, and ensure that there are no gaps between the computer and the cover. Tighten the two screws at the bottom of the computer to secure the back cover to the back of the computer.
- Page 19 Replace the VESA cover on the back of the computer. Be sure to align the tabs on the VESA cover with the slots on the back of the computer and snap the cover into place. Place the computer in an upright position. Connect the power cord.