JVC RMP-2580U - Remote Controller For Color Domes Instructions Manual page 6

1. INTRODUCTION
CONTROLS, CONNECTORS AND INDICATORS (Continued)
‹
¤
⁄
)
8
[AUTO] button
When this button is pressed, the unit enters the AUTO SE-
QUENCE mode, in which the indicator lights up and the
MONITOR OUTPUT 1 connector
put the camera video signals according to automatic switch-
ing.
REF. : "AUTO SEQUENCE OPERATION" on page 13.
9
[F1, F2, F3] Function buttons
These buttons are valid only when SW-D7000/SW-D8000
frame switchers are being used.
When this unit is operated in the B mode, these buttons
can control certain functions of the specific frame switcher
model connected to this unit. The RS-232C control is in-
volved in this control operation.
For details, please consult your dealer or JVC-authorized
service agent.
REF. : "APPLIED SYSTEM (B MODE)" on page 22.
F1: Single-screen select switch
Press this button to output a single-screen video from
the frame switcher.
The camera number can be selected using the numeric
keypad, etc.
F2: Split-screen select switch
Press this button to output a split-screen video from
the frame switcher.
F3: LIVE/PLAY switch
Press this button to switch between the playback video
of a time-lapse VCR and the camera video.
0
[CAMERA] button
Press when selecting a camera.
To select a camera, use the following buttons:
0
CAMERA button Numeric key buttons
&
ENTER button .
REF. : "CAMERA SELECTION" on page 10.
6
CAMERA CAMERA
SETUP SETUP
PO POWER WER
ALARM ALARM
MENU MENU SET SET
KEY LOCK KEY LOCK
LENS LENS CAMERA/POSITION
1 2
SPEED SPEED
4 5
IRIS IRIS
CLOSE CLOSE OPEN OPEN
FOCUS FOCUS
7 8
NEAR NEAR FAR FAR
AF AF
0
ZOOM ZOOM TELE TELE CLEAR CLEAR ENTER ENTER
WIDE WIDE
/HOME /HOME
( * &
‚
on the rear panel out-
*
REMOTE CONTROL UNIT REMOTE CONTROL UNIT RM-P2580 RM-P2580
POSITION POSITION
AUTO AUTO F-1 F-1 F-2 F-2
PAN/TILT PAN/TILT
3
CAMERA CAMERA POSI- POSI-
TION TION
6
OPTION OPTION OPTION OPTION
1 2
9 AUTO AUTO AUTO AUTO
PAN PAN PATROL PATROL
^ % $
!
[POSITION] button
Press when selecting one of the position numbers preset
for the camera.
To select a position, use the following buttons:
POSITION button
&
TER button .
REF. : "POSITION SELECTION" on page 11.
@
[OPTION 1, 2]
These buttons are not used for the present. Do not touch
them.
#
[PAN/TILT] control lever
Operate the lever to pan (swing horizontally) or tilt (swing
vertically) the rotary turret of a camera.
8(Up) : Tilt the lever in this direction to tilt the rotary
turret upward.
9(Down) : Tilt the lever in this direction to tilt the rotary
turret downward.
;(Right) : Tilt the lever in this direction to pan the rotary
turret toward the right.
:(Left) : Tilt the lever in this direction to pan the rotary
turret toward the left.
REF. : "MANUAL OPERATION" on page 12.
While a menu screen is displayed, this lever is used to
select or to set an item.
REF. : "MENU OPERATION METHOD" on page 26.
8
9
F-3 F-3
0
!
@
#
!
Numeric key buttons
*
EN-