1. Manuals
  2. Brands
  3. Bulldog Security Manuals
  4. Remote Starter
  5. KE100, KE150, 1702
  6. Installation manual

Bulldog Security KE100, KE150, 1702 Installation Manual

Ke100, ke150, 1702 installation guide & owner’s guide
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

INSTALLATION GUIDE
KEYLESS ENTRY • MODELS KE100 / KE150 / 1702
CONTENTS
System Features .......................................
System Components .....................................
Technical Assistance ..................................
Before You Begin ......................................
Precautions .........................................
Making Wiring Connections............................ 2-3
Locating & Making Connections........................ 3-4
Testing Door Locks ....................................
Connecting Door Locks ............................... 5-6
14-Pin Harness Diagram ................................ 6
Door Lock Type by Manufacturer ......................... 6
Operating Instructions ................................ 6
Programming Instructions .............................. 7
Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.
OWNER'S GUIDE
Technical Assistance
All tech personnel are expertly qualified to answer any technical questions.
288 Canton Avenue • Wintersville, Ohio 43953
Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306
•
Address
Telephone
1
1
1
1
1-2
5

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KE100, KE150, 1702 and is the answer not in the manual?

Questions and answers

Related Manuals for Bulldog Security KE100, KE150, 1702

Summary of Contents for Bulldog Security KE100, KE150, 1702

  • Page 1: Table Of Contents

    INSTALLATION GUIDE • OWNER’S GUIDE KEYLESS ENTRY • MODELS KE100 / KE150 / 1702 CONTENTS System Features ........System Components ........Technical Assistance ........Before You Begin ........Precautions ......... Making Wiring Connections......2-3 Locating & Making Connections......3-4 Locating & Determining Your Door Lock Types .... 5 Testing Door Locks ........

  • Page 2: System Features

    It is computer controlled and manufactured in the U.S.A. The dependability and variety of features make Bulldog Security the leader in the industry. Enjoy your new keyless entry for years to come! Read this manual thoroughly before starting the installation. You must also decide if any options are desired such as starter immobilizer, trunk release and parking light confirmation.

  • Page 3: Making Wiring Connections

    DO NOT leave the interior or exterior lights on for an extended period of time as it may cause battery drain. DO NOT mount the control module until all connections have been made and tested. Using wire ties or double sided tape, MOUNT THE MODULE UNDER THE DASH. MAKING WIRING CONNECTIONS 1.

  • Page 4: Locating & Making Connections

    MAKING END TO END CONNECTIONS FOLLOW THESE INSTRUCTIONS 1. When tying two separate wires together at their ends, strip back 1” of insulation on both wires and separate the strands of wire as shown below. 2. Twist upper wires together, twist lower wires together as shown. 3.
  • Page 5 CHASSIS GROUND Factory Bolt Black Ground Wire Locate an easy to get to bolt or screw located under the driver’s side of the Note: Remove any paint below dash and attach the BLACK ground wire the spade connector. Spade Connector from the 14-pin harness securely as pictured.

  • Page 6: Locating & Determining Your Door Lock Types

    LOCATING AND DETERMINING YOUR DOOR LOCK TYPE In most cases, the factory door lock wires will be smaller gauge and located in the driver’s kick panel or under the driver’s dash. NOTE: To help determine your door lock type, refer to the Door Lock Types by Manufacturer chart on page 13 or visit our web page at www.bulldogsecurity.com for specific detailed information on a particular vehicle.

  • Page 7: 14-Pin Harness Diagram

    14-PIN HARNESS DIAGRAM “Type C” Reverse Polarity +12V Constant BLACK Ground (+)12V Constant POWER BLACK Ground BLUE/BLACK Unlock DOOR LOCK BROWN (-)Parking Light Output MOTOR BROWN/BLACK Unlock WHITE/RED (-)Trunk Pop ORANGE (-)Starter Kill PURPLE RED/BLACK (-)FASD +12V not used PURPLE/BLACK FUSE Constant WHITE/BLACK...

  • Page 8: Programming Instructions

    PROGRAMMING INSTRUCTIONS In most cases the programming will NOT be used. To enter programming mode BUTTON #1 Press button #4 for 10 seconds then release. You are now in programming Locks your mode. To exit programming mode press and release button #4 again. vehicle.

Table of Contents