Table of Contents
Advertisement
Available languages
Available languages
TO REPLACE
MOWER
DRIVE
BELT
MOWER
DRIVE
BELT REMOVAL
1,
Park tractor
on a level surface,
Engage
parking
brake.
2_ Lower attachment
lift lever to its lowest
position_
3,
Disengage
belt tension
rod (K) from lock
bracket
(L),
AUTION:
Belttension
rod is spring load-
ed. Have afirm grip on rod and release slowly,
4_ Remove
screws
(P) from R.H. and L.H.
mandrel
covers and remove covers (Q),
5.
Remove any dirtorgrass
clippings which
may have accumulated
around mandrels
and entire upper deck surface,
6.
Remove
belt from electric
clutch pulley
(M), both mandrel
pulleys (R) and allidler
pulleys
(S).
%
NOTE: Observe
entire motion drive belt and
position of all belt guides
and keepers.
2. Disconnect
clutch wire harness
(A),
3. Remove anti-rotation
link (B) on right side
of tractor.
4. Remove
beltfrom
stationary
idler (C) and
clutching
idler (D).
5, Pull belt
slack
toward
rear
of tractor.
Carefully
remove
belt
upwards
from
transmission
input pulley and over cool-
ing fan blades
(F),
6.
Remove
belt
downward
from
engine
pulley and around
electric
clutch
(G).
7. Slide belt toward
rear of tractor,
off the
steering plate (H) and remove from tractor_
MOWER
DRIVE
BELT INSTALLATION
I,
Install belt around
both mandrel
pulleys
(R) and around idler pulleys (S) as shown.
2. Install belt onto electric clutch pulley (M),
IMPORTANT:
Check belt for proper routing
in all mower pulley grooves.
3, Reassemble
R.H. and L.H. mandrel
cov-
ers (Q), Securely
tighten all screws,
4, Engage
belt tension
rod (K) on locking
bracket
(L),
A CAUTION:
Belttension rod is spring load-
ed, Have a tight grip on rod and engage slowly.
5, Raise
attachment
lift lever
to highest
position,
TO REPLACE MOTION DRIVE BELT
Park the tractor on level surface.
Engage
parking brake.
For assistance, there is a
belt installation guide decal on bottom side
of left footrest.
BELT REMOVAL-
1,
Remove
mower
(See
"TO
REMOVE
MOWER"
in this section
of manual),
BELT INSTALLATION
-
t,
Install new belt from tractor rear to front,
over the steering
plate
(H) and above
clutch brake pedal shaft (J).
2o Pull belt toward front of tractor and roll belt
around
electric
clutch
and onto engine
pulley (G).
3,
Pull belt toward
rear of tractor. Carefully
work
belt
down
around
transmission
cooling fan and onto the input pulley (F),
Be sure belt is inside the belt keeper_
4.
Install
belt through
stationary
idler (C)
and clutching
idler (D).
5,
Reinstall
anti-rotation
link (B) on right
side of tractor. Tighten
securely,
6.
Reconnect
clutch
harness
(A).
7. Make sure belt is in all pulley
grooves
and inside all belt guides
and keepers.
8.
Install mower
(See 'q'O INSTALL
MOW-
ER" in this section
of manual).
28
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the 28947 - GT 5000 26 HP/54" Garden Tractor and is the answer not in the manual?
Questions and answers
gt 5000 riding mower will not turn deck on
The Craftsman GT 5000 26 HP/54" Garden Tractor deck may not turn on due to the following possible causes:
1. Attachment Clutch Control Not Engaged – Ensure the attachment clutch control is in the "ENGAGED" position.
2. Worn or Broken Belt – Check the mower deck belt for wear or damage and replace if necessary.
3. Electrical Connection Issues – Inspect wiring and connections related to the deck engagement system.
4. Faulty PTO (Power Take-Off) Switch – If equipped with an electric PTO, ensure the switch is functioning correctly.
5. Blown Fuse – Check for a blown fuse in the electrical system and replace it if needed.
6. Disengaged Safety Features – Ensure seat safety switch and other safety mechanisms are properly engaged.
7. Mechanical Obstruction – Check for debris or obstructions preventing the deck from operating.
If the issue persists, refer to the troubleshooting section of the manual or contact a qualified service center.
This answer is automatically generated
Looking for parts manual for a fs 5500 tractor
Wiring dram for a 2011 sears riding lawnmower with a 26 horse kosher engine
Engine starts and begins to run then stalls
The Craftsman GT 5000 26 HP/54" Garden Tractor engine may start and then stall due to one or more of the following causes:
1. Stale or dirty fuel – empty the fuel tank and refill with fresh gasoline.
2. Water in the fuel – empty the fuel tank and carburetor, refill with fresh gasoline, and replace the fuel filter.
3. Dirty or clogged fuel filter – replace the fuel filter.
4. Dirty air filter – clean or replace the air filter.
5. Faulty spark plug – clean, regap, or replace the spark plug.
6. Loose spark plug wire – connect and tighten the spark plug wire.
7. Carburetor issues – may require adjustment or cleaning.
These issues can cause the engine to run poorly or stall shortly after starting.
This answer is automatically generated