Sanyo PDG-DWT50L - WXGA DLP Projector User Manual
  1. Manuals
  2. Brands
  3. Sanyo Manuals
  4. Projector
  5. PDG-DWT50L - WXGA DLP Projector
  6. User manual

Sanyo PDG-DWT50L - WXGA DLP Projector User Manual

Owners manual
Hide thumbs Also See for PDG-DWT50L - WXGA DLP Projector:
Table of Contents

Advertisement

Quick Links

See also: Service Manual

Advertisement

Table of Contents
loading

Related Manuals for Sanyo PDG-DWT50L - WXGA DLP Projector

Summary of Contents for Sanyo PDG-DWT50L - WXGA DLP Projector

  • Page 2 (4) Great care has been taken in the preparation of this user’s manual; however, should you notice any questionable points, errors or omissions, please contact us. (5) Notwithstanding article (3), SANYO will not be responsible for any claims on loss of profit or other matters deemed to result from using the Projector.

  • Page 3: To The Owner

    When hanging the projector from the ceil- ing, clean air intake vents, filters, or top of Your SANYO product is designed and manu- the projector periodically with a vacuum factured with high quality materials and cleaner.

  • Page 4: Safety Instructions

    Safety Instructions All the safety and operating instructions should be read Do not install the projector near the ventilation duct of air- before the product is operated. conditioning equipment. Read all of the instructions given here and retain them for This projector should be operated only from the type of later use.

  • Page 5: Important Information

    Important Information Air Circulation Openings in the cabinet are provided for ventilation. To IMPORTANT! ensure reliable operation of the product and to protect it Clean the Filter Regularly!! from overheating, these openings must not be blocked or covered. The projector uses a lamp which generates significant heat.

  • Page 6: Federal Communications Commission Notice

    Model Number(s) : PDG-DWT50L Trade Name : Sanyo Responsible party : SANYO FISHER COMPANY Address : 21605 Plummer Street, Chatsworth, California 91311 U.S.A. Telephone No. : (818)998-7322 AC Power Cord Requirement The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

  • Page 7: Table Of Contents

    Table of Contents 1. INTRODUCTION ....................................1 ’ ? ..................................1 S IN THE ..............................2 NTRODUCTION TO THE ROJECTOR Features you’ll enjoy:..................................2 ..............................3 AMES OF THE ROJECTOR Front-right view....................................3 Top view ......................................4 Bottom view .......................................5 ....................................6 EATURES Lens Controls.....................................6 OSD Controls and Status LEDs..............................7 ................................9 ERMINAL ANEL...
  • Page 8 Table of Contents Adjusting by Using the OSD Control Panel..........................44 ..................................45 HANGING Changing Lamp Mode by Using the Projector's OSD Control Panel ..................45 Changing Lamp Mode by Using the Remote Control ........................46 ..................................47 ETTING NFORMATION ..........................48 DJUSTING OSITION OTAL Adjusting Position/Total Dots/Fine Sync by using the OSD Control Panel ................48 Correcting Keystone by Using the Remote Control ........................49 ......................51 REVENTING THE...
  • Page 9 Table of Contents Lamp Problems .....................................105 Remote Control Problems ................................106 Audio Problems .....................................106 ..............................106 AVING THE ROJECTOR ERVICED 8. SPECIFICATIONS ...................................107 .................................107 ROJECTOR PECIFICATIONS Optical Specifications ...................................107 Electrical Specifications ................................108 Mechanical Specifications ................................109 Environmental Considerations ..............................109 Regulations ....................................109 Optional Parts ....................................110 ..................................111 ABINET IMENSIONS...

  • Page 10: Introduction

    1. Introduction What’s in the Box? Carefully unpack the projector and check that the following items are included: PDG-DWT50L Projector Remote Control (with Two AA alkaline batteries) Power Cable (3.6m/11.8 ft.) → For North America, Europe and the UK Quick Start Guide Remote Cable (10m/33ft) VGA Cable...

  • Page 11: Introduction To The Projector

    1. Introduction Introduction to the Projector Features you’ll enjoy: DLP projector with high resolution The combination of BrilliantColor™ and a six-segment color wheel (optional) offer a more true color reproduction. Installation Flexibility This projector has many useful functions such as powered lens shifting, ceiling and rear projection, variety of extensive op- tional powered lens with bayonet mount with release button, etc.

  • Page 12: Part Names Of The Projector

    1. Introduction Part Names of the Projector Front-right view ABEL ESCRIPTION IR receiver Receiver for IR signal from remote control Lamp cover Remove cover to replace lamp or color wheel Lens control panel See Lens Controls OSD control panel See OSD Controls and Status LEDS I/O connector panel Connect various input devices —...

  • Page 13: Top View

    1. Introduction Top view ABEL ESCRIPTION Lens control panel See Lens Controls — Right-hand speaker Right-hand speaker Lamp cover Remove cover to replace lamp or color wheel — Exhaust vent Exhaust vent – do not obstruct OSD control panel See OSD Controls and Status LEDS —...

  • Page 14: Bottom View

    1. Introduction Bottom view ABEL ESCRIPTION AGES Height adjusters Adjust projection height — Intake vent Color wheel cooling vent – do not obstruct Keep the fan free of dust – clean regularly for optimum perform- Front filter ance Contact your dealer for information on mounting the projector on —...

  • Page 15: Top Features

    1. Introduction Top Features Lens Controls ABEL ESCRIPTION EE PAGE ZOOM Increase/decrease projected image size UP CURSOR RIGHT CURSOR Move image left, right, up, or down DOWN CURSOR LEFT CURSOR FOCUS Focus the projected image...

  • Page 16: Osd Controls And Status Leds

    1. Introduction OSD Controls and Status LEDs ABEL ESCRIPTION MENU Open / Close the OSD UP/ DOWN/ LEFT/ Navigate and change settings in the OSD RIGHT BUTTONS RIGHT CURSOR/ VOLUME Increase volume INCREASE CANCEL Exit the On-Screen Display (OSD) INPUT Change or select the input device Turn the projector on or off (main power switch must be turned ON/STAND-BY...
  • Page 17 1. Introduction ABEL ESCRIPTION LAMP 1 (LED) See Indicator Messages WARNING (LED) See Indicator Messages POWER (LED) See Indicator Messages AUTO PC ADJ. Optimize image size, position, and resolution SELECT Select or change settings in the OSD LEFT CURSOR/VOLUME Decrease volume DECREASE...

  • Page 18: Terminal Panel Features

    1. Introduction Terminal Panel Features ABEL ESCRIPTION COMPUTER 3 IN Connect the DVI-D cable (not supplied) from a computer AUDIO IN — Connect the audio cable (not supplied) from the input device (COMPUTER 3) — AUDIO OUT Audio loop-thru — MONITOR OUT Connect to a monitor R/C JACK...
  • Page 19 1. Introduction ABEL ESCRIPTION When connected to the screen through a commercially available SCREEN cable, the screen deploys automatically on start up of the projec- TRIGGER tor. The screen retracts when the projector is powered off (see notes below) Connect a commercially available S-video cable from a video S-VIDEO device POWER SWITCH...

  • Page 20: Part Names Of The Remote Control

    1. Introduction Part Names of the Remote Control ABEL ABEL NO SHOW Temporarily turns off screen image. D. ZOOM -/+ STAND-BY Zoom in/out function. AUTO PC LIGHT Automatically adjust the Illuminate the remote panel. computer image. MENU KEYSTONE Open or close the on-Screen Correct keystone distortion.
  • Page 21 1. Introduction Important: Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation. 1. Be sure nothing obstructs the path between the remote control and the projector. If the path between re- mote and projector is obstructed, you can bounce the remote signal off certain reflective surfaces such as projector screens.

  • Page 22: Battery Installation

    1. Introduction Battery Installation The Remote Control unit included with the projector does not contain batteries, though batteries are supplied as part of the complete package. To insert (or replace) the batteries, refer to the following guide. Remove the battery compartment cover by squeezing the locking catch and slid- ing the cover in the direction of the arrow.

  • Page 23: Operating Range For Wireless Remote Control

    1. Introduction Operating Range for Wireless Remote Control Point the remote control toward the projector (to Infrared Remote Re- ceivers) when pressing the buttons. Maximum operating range for the remote control is about 16.4 feet (5 m) and 60 degrees in front and rear of the projector.

  • Page 24: Using The Remote Control In Wired Operation

    1. Introduction Using the Remote Control in Wired Operation Connect the supplied remote cable to the R/C jack on the projector (see Terminal Panel Features on page 9) and the other end to the remote jack on the remote control (see item 1, Part Names of the Remote Control on page 11).

  • Page 25: Carrying The Projector

    1. Introduction Carrying the Projector Always carry your projector by the handle. Before moving or carrying the projector, disconnect the power cable and any other cables that may be attached to it. When moving the projector or when the projector is not in use, cover the lens with the lens cap. To extend the projector handle, refer to the following guide.

  • Page 26: Installation And Connections

    2. Installation and Connections Setting Up the Screen and the Projector This section briefly describes how to set up your projector and how to connect video and audio sources. Your projector is simple to set up and use. But before you get started, you must first: •...

  • Page 27: Selecting A Location

    2. Installation and Connections Selecting a Location Locating the projector correctly ensures optimum performance and a longer parts life. Take note of the following when setting up the projector: • The projector table or stand should be level and sturdy. •...

  • Page 28: Installing Or Removing The Optional Lens

    2. Installation and Connections Installing or Removing the Optional Lens • Do not shake or place excessive pressure on the projector or the lens components as the projector and lens components contain precision parts. • When shipping the projector with the optional lens, remove the optional lens before shipping the projec- tor.

  • Page 29: Installing The New Lens

    2. Installation and Connections Pull out the existing lens slowly. CAUTION When Installing the lens into the projector, be sure to remove the lens cap from the back of the optional lens before installing the optional lens into the projector. Failure to do so will cause damage to the projec- tor.

  • Page 30: Installing The New Lens Using The Anti-Theft Screw

    2. Installation and Connections Installing the New Lens Using the anti-theft screw Using the anti-theft screw to prevent theft of the lens. Tighten the supplied anti-theft screw on the front bottom.

  • Page 31: Throw Distance And Screen Size

    2. Installation and Connections Throw Distance and Screen Size Example of LNS-S40: The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approxi- mately 40 inches (1 m) measured diagonally when the projector is roughly 71 inches (1.8 m) from the wall or screen. The largest the image can be is 500 inches (12.7 m) when the projector is about 915 inches (23.2 m) from the wall or screen.
  • Page 32 49.74 - 93.56 1984.9 1958.2 - 3683.4 Ceiling installation must be done by a qualified professional. Contact your SANYO dealer for more information. It is not recommended you install the projector yourself. Only use the projector on a solid, level surface. Serious injury and damage can occur if the projector is dropped.

  • Page 33: Installing The Optional Color Wheel

    2. Installation and Connections Installing the Optional Color Wheel The PDG-DWT50L projector comes with a four-segment color wheel installed. An additional six-segment color wheel is op- tional. To replace the color wheel (located under the lamp cover adjacent to lamp 1) refer to the following guide. Note: Wait until the lamp house and the color wheel cool off.
  • Page 34 2. Installation and Connections Lift the color wheel in the di- rection shown. Insert the six-segment color wheel Secure the retaining screws as shown.

  • Page 35: Making Connections

    2. Installation and Connections Align the lamp cover (A) with the arrow mark on the cabinet and slide it into place. Secure the captive screw (B). Storing Unused Color Wheel: Keep the unused color wheel in the zipper bag in which the 6-segment color wheel (not supplied) was packaged. This bag prevents dust from falling or collecting on the color wheel.
  • Page 36 2. Installation and Connections 2. Turn on the projector and select the chosen method of connection from the source menu before turning on the PC (see Selecting an Input Source on page 34). 3. Turn on the PC. Note: Failure to follow the above steps may not activate the digital output of the graphics card resulting in no pic- ture being displayed.

  • Page 37: Connecting An External Monitor

    2. Installation and Connections Connecting an External Monitor Connect an external monitor to the projector through RGB out connections as shown below (see item 4, Terminal Panel Features on page 9)

  • Page 38: Connecting Your Dvd Player With Component Output

    2. Installation and Connections Connecting Your DVD Player with Component Output To connect a DVD Player to the projector, refer to the following guide. 1. Connect the DVD Player to the projector as shown below before turning on the Player or the projector. 2.

  • Page 39: Connecting Your Vcr Or Laser Disc Player

    2. Installation and Connections Connecting Your VCR or Laser Disc Player To connect your VCR or Laser Disc Player, refer to the following diagram. Note: Refer to your VCR or laser disc player user’s manual for more information about your device’s requirements. Images may not be displayed correctly when using an S-Video or Video connection to fast-forward or fast- rewind scanning.

  • Page 40: Connecting The Supplied Power Cable

    2. Installation and Connections Connecting the Supplied Power Cable This projector uses nominal input voltages of 100–120V or 200–240V AC and it automatically selects the correct input volt- age. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system.

  • Page 41: Projecting An Image (Basic Operation)

    3. Projecting an Image (Basic Operation) Turning on the Projector Once the projector is correctly located and the power cable and other connections are in place, it is important that the pro- jector is powered on correctly in order to avoid damage to components and unnecessary wear and tear. Refer to the following guide to power on the projector.

  • Page 42: Note On Startup Screen (Menu Language Select Screen)

    3. Projecting an Image (Basic Operation) Note on Startup Screen (Menu Language Select screen) In the first instance of powering on the projector, the language menu is displayed to select the default language. Select the required default language using the ▲ or ▼ buttons on the OSD menu panel or the remote control unit and press Select.

  • Page 43: Selecting An Input Source

    3. Projecting an Image (Basic Operation) Selecting an Input Source The Input Source can be selected from the projector's control panel or from the remote control unit. Refer to the following guide to select the Input Source. Press Menu on the OSD control panel or on the remote control unit to display the Main Menu.

  • Page 44: Adjusting The Picture Position And Picture Size

    3. Projecting an Image (Basic Operation) Adjusting the Picture Position and Picture Size The Picture Position and Picture Size can be adjusted manually from the lens control panel or from the remote control unit. Refer to the following guides to adjust Picture Position manually. Adjusting Picture Position Manually Press the Select keypad in any direction to bring up the Lens Shift window.

  • Page 45: Lens Shift Adjustable Range

    3. Projecting an Image (Basic Operation) The Screen window is displayed. Select the desired picture size using ▲or▼ and press Select. When finished, press Cancel to return to the projected image. Lens Shift Adjustable Range The adjustable range for lens shift is tabulated below and subject to the conditions listed. Note: The drawings below apply to the standard lens (LNS-S40) only.

  • Page 46: From The Remote Control Unit

    3. Projecting an Image (Basic Operation) From the Remote Control Unit Press the Lens Shift button to bring up the Lens Shift window. Press the directional keys as required to shift the image. Releasing the directional arrow will re-center the cursor. To alter the picture size, press the Screen button to display the Screen window.

  • Page 47: Adjusting The Projector Level

    3. Projecting an Image (Basic Operation) Adjusting the Projector Level To raise the level of the projector, twist the adjust- ers clockwise. To lower the level of the projector, lift the projector and twist the adjusters counter clockwise.

  • Page 48: Optimizing An Rgb Image Automatically

    3. Projecting an Image (Basic Operation) Optimizing an RGB Image Automatically Adjusting the Image Using AUTO PC ADJ. To optimize an RGB image automatically refer to the following guide. Press the AUTO PC button on the remote control (see item 17, Part Names of the Remote Control on page 11) or the AUTO PC ADJ.

  • Page 49: Adjusting Volume Up And Down

    3. Projecting an Image (Basic Operation) Adjusting Volume Up and Down The volume can be adjusted from the OSD Control Panel or with the Remote Control unit. Refer to the following as a guide. Press the Volume +/- buttons on the remote control or the ◄...

  • Page 50: Turning Off The Projector

    3. Projecting an Image (Basic Operation) Turning off the Projector Once the projector is no longer required, it is important to shut it down correctly to avoid damage or unnecessary wear and tear to the projector. • Do not unplug the power cable from the wall outlet or projector when the projector is powered on. Doing so can cause damage to the AC IN connector of the projector and (or) the prong plug of the CAUTION power cable.

  • Page 51: About Direct Power Off

    3. Projecting an Image (Basic Operation) About Direct Power Off The projector has a feature called "Direct Power Off". This feature allows the projector to be turned off (even when projecting an image) using a power strip equipped with a switch and a breaker. Note: Before using Direct Power Off, be sure to allow at least 20 minutes immediately after turning on the projector and starting to display an image.

  • Page 52: Convenient Features

    4. Convenient Features Turning Off the Image and Sound The projected image and sound can be turned off for short periods of time with the remote control. This feature is useful for breaking up presentations or for other brief interruptions in projections. To turn off the picture and image, refer to the following guide.

  • Page 53: Adjusting The Focus/Zoom Manually

    4. Convenient Features Adjusting the Focus/Zoom Manually The focus and zoom can be adjusted manually from the projector focus/zoom panel or from the remote control unit. Refer to the following guides to adjust the focus and zoom manually. Adjusting by Using the OSD Control Panel Press the Focus or Zoom button on the projector panel to display the appropriate window.

  • Page 54: Changing Lamp Mode

    4. Convenient Features Changing Lamp Mode The projector has two lamp modes available, Normal and Eco. The Normal mode is used for everyday standard projec- tion, whereas the Eco mode is used for saving power and lamp life. To change the Lamp Mode, refer to the following guides.

  • Page 55: Changing Lamp Mode By Using The Remote Control

    4. Convenient Features Changing Lamp Mode by Using the Remote Control Press the Lamp control button on the remote control to ac- cess the Lamp control menu. From the Lamp control window, select Normal or Eco us- ing ▲or▼. Move the cursor to OK and press Select. Note: When the projector is in Eco mode, brightness may be affected.

  • Page 56: Getting Information

    4. Convenient Features Getting Information The Information screen provides details on the life of consumable items within the projector as well as other information such as software version. To access the Information screen, refer to the following guide. Press Menu on the projector's OSD control panel or remote control to display the Main Menu.

  • Page 57: Adjusting Position/Total Dots/Fine Sync

    4. Convenient Features Adjusting Position/Total Dots/Fine Sync The Position/Total dots/Fine sync and Keystone Correction can be adjusted manually from the projector's control panel or from the remote control unit. Refer to the following guides to adjust the Keystone Distortion manually. Adjusting Position/Total Dots/Fine Sync by using the OSD Control Panel Press the Menu button to display the Main menu.

  • Page 58: Correcting Keystone By Using The Remote Control

    4. Convenient Features Correcting Keystone by Using the Remote Control Press the Keystone but- ton to display the Keystone window. Adjust the Horizontal and Vertical sliding bars using the select ▲▼◄► buttons. Adjust the slide bars until the screen trapezoid is a regular shape (see dia- gram).
  • Page 59 4. Convenient Features DJUSTMENT ORIZONTAL ERTICAL Keystone Max. +/– 35° approx. Max. +/– 40° approx. The following are conditions under which the maximum angle is achieved: When the standard lens (LNS-S40) is used When the lens shift is set to H for center and V for 0.5 shift. When the lens shift is used and yet you do not get the above-mentioned condition (H for center and V for 0.5 shift), you cannot adjust the keystone correctly.

  • Page 60: Preventing The Unauthorized Use Of The Projector

    4. Convenient Features Preventing the Unauthorized Use of the Projector The projector has a built-in security feature to lock the OSD control panels and deny remote control operation. The security feature has no default keyword; in the first instance of enabling the security feature, the user must define a keyword. Locking the Projector To setup the security keyword, refer to the following guide.
  • Page 61 4. Convenient Features The PIN code window is displayed. Enter a PIN code between 4 and 10 characters using ▲▼◄►. The PIN code characters change to “ * ”. Press Select. Once a successful PIN code is entered, a confirmation screen is displayed. Enter the same password as the previous step and write it down for later reference.

  • Page 62: Unlocking The Projector

    4. Convenient Features Unlocking the Projector To unlock the projector, refer to the following guide. When the projector is locked, either by re- quest during operation or at start up, the locked message is displayed. To unlock the projector, press Menu on the control panel or remote control.

  • Page 63: Using The Physical Lock

    4. Convenient Features Using the Physical Lock For security and authorized usage, the projector comes with two types of security features, the Kensington Lock and the Security Chain Lock. Using the Kensington Lock If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable.

  • Page 64: Using On-Screen Display

    5. Using On-Screen Display Using the Menus The projector has an On-Screen Display (OSD) that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the remote control and on the projector.
  • Page 65 5. Using On-Screen Display Press the cursor ◄ or ► button to move through secondary menus. Press ▲or▼ to select menu items and ◄or► to change values for settings. Press Select to confirm the new setting. Press Cancel to close the OSD or leave a submenu.

  • Page 66: Menu Tree

    5. Using On-Screen Display Menu Tree The gray shaded areas indicate factory default settings. Input Computer 1, Computer 2, Computer 3, Component, Video, S-Video CrossHatch, Raster(0%), Raster(25%), Raster(50%), Raster(100%), Raster Red, Raster Test pattern Green, Raster Blue, Raster Blue 60, Gray Raster 10, Gray Raster 30, Ramp H, Ramp V, Red Ramp H Adjust Image...
  • Page 67 5. Using On-Screen Display Installation Ceiling & Rear Desktop Front/Ceiling Rear/Desktop Rear/Ceiling Front Communication speed 4800bps/9600bps/19200bps/38400bps Menu color select Color/Monochrome Display time Manual/Auto 5sec/Auto 15sec/Auto 45sec Background Blue/Black/Logo PIN code lock Off/On Key lock Off/On Dynamic black Off/On RC sensor Both, Front, Back Network setting DHCP...

  • Page 68: Menu Elements

    5. Using On-Screen Display Menu Elements Some menus and windows contain large amounts of information in a small area. Refer to the following guide to navigate through options more easily. Menu windows or dialog windows typically contain the following elements: ABEL ESCRIPTION Title...

  • Page 69: Source Menu Descriptions And Functions

    5. Using On-Screen Display Source Menu Descriptions and Functions The Source menu displays all supported image sources. Select the required source from the menu using ▲ or ▼ and press Select to confirm. ESCRIPTION Select the source connected to the Computer 1 input Computer 1 (see Connecting Your PC or Macintosh Computer on page 26).

  • Page 70: Adjust Menu Descriptions And Functions

    5. Using On-Screen Display Adjust Menu Descriptions and Functions The Adjust menu contains overall projector settings for image output such as sharpness, overscan and color matrix. Three tabs are accessible through the Adjust menu, Picture, Image Options and Video. Image menu The image menu is used to alter picture settings and can be accessed from the Adjust menu.

  • Page 71: Image Options Menu

    5. Using On-Screen Display Image options menu The Image Options menu is used to configure image options such as screen positioning and aspect ratio. Access the im- age options menu in the Adjust menu. The following table lists all functions with a description and the default setting. ESCRIPTION Screen Select Screen using ◄or►...
  • Page 72 5. Using On-Screen Display Screen The screen option allows for the adjustment of the aspect ratio to alter the appearance or ratio of the projected image. 4:3 – Standard TV screen (4:3), proportionally four units wide for every three units high, no matter the size of the screen. 16:9 –...

  • Page 73: Video Menu

    5. Using On-Screen Display Video menu The Video menu is used to configure image options such as film. Access the Video menu in the Adjust menu. The following table lists all functions with a description and the default setting. A detailed description follows the table. ESCRIPTION Noise reduction Select Noise reduction mode (see page 65).
  • Page 74 5. Using On-Screen Display Noise reduction Select the level of noise reduction required. Range: Off, Low, Mid, High. 3D Y/C separation 3D Y/C Separation separates composite signal to Y (brightness) signal and C (color) signal, and can help to produce clearer and sharper images without overlapping colors (rainbow effect).
  • Page 75 5. Using On-Screen Display Color matrix Color Matrices define the amount of the three-color components R (red), G (green), and B (blue) in a single point in color space. Select from the following: Auto – Auto selects the color matrix. RGB –...

  • Page 76: Detail Settings Menu Descriptions And Functions

    5. Using On-Screen Display Detail Settings Menu Descriptions and Functions The Detail settings menu contains basic and advanced color adjustment options such as gamma correction, color contrast and color correction. Basic The Basic tab contains general Detail Settings such as gamma correction and color temperature. Access to the General tab is through the Detail Settings menu.
  • Page 77 5. Using On-Screen Display Reference The Reference mode allows the projector to differentiate between source materials for example movies, PC images or video stills. Select from the following: High-bright – Select for use in a brightly lit room. Presentation – Select if the projector is to be used for presentation purposes. Video –...

  • Page 78: White Balance

    5. Using On-Screen Display White balance White Balance allows the projector to compensate for different colors of light being emitted by different light sources. The following table lists all functions with a brief description. ESCRIPTION Set the value to compensate for red light sources. Green Set the value to compensate for green light sources.

  • Page 79: Color Correction

    5. Using On-Screen Display Color correction The Color correction tab enables the adjustment of color values in an image to remove unwanted effects, improve color, characteristics or add more of a particular color. The following table lists all functions with a brief description. ESCRIPTION Increase or decrease the amount of red in the projected output using ◄...

  • Page 80: Setting Menu Descriptions And Functions

    5. Using On-Screen Display Setting Menu Descriptions and Functions The Setup menus contain the most often used settings during installation and options to customize the general output of the projector. Three tabs are accessible through the Setup menu, general, installation and option. Basic The Basic tab contains general setup options such as lamp mode and OSD language settings and can be accessed with the projector control panel or with the remote control unit.
  • Page 81 5. Using On-Screen Display Keystone The keystone trapezoid can be adjusted by selecting this option. Select Horizontal or Vertical using ▲or▼ then, use ◄or► to adjust the projected image appearance as required. Lamp control Select Normal or Eco from the lamp mode window. The lamp life can be extended by using the Eco mode and the fan noise can be reduced.
  • Page 82 5. Using On-Screen Display Lamp interval The period of time for regulating lamp usage when not in dual lamp mode. Select from the following: Off, 1 week, 4 weeks and 2000H Simple menu Select the Simple menu to display. Set Simple menu On or Off.
  • Page 83 5. Using On-Screen Display Language Select the OSD language to be used. Select from the following: English German French Italian Spanish Swedish Japanese Simplified Chinese...

  • Page 84: Installation

    5. Using On-Screen Display Installation The Installation tab contains menu options for various setup conditions such as orientation and remote sensor mode and is accessed through the Setup menu. The following table lists all functions with a brief description. ESCRIPTION Select from four projection methods depending on projection site Ceiling &...
  • Page 85 5. Using On-Screen Display ESCRIPTION Set Control panel lock On/Off. Note: Key lock This Control Panel Lock does not affect the remote control functions. When the control panel is locked, pressing and holding the Cancel button on the projector cabinet for about 10 seconds. The setting will change to Off. DynamicBlack improves the black level of the projector.
  • Page 86 5. Using On-Screen Display Communication speed Select communication speed to set the baud rate of the connection. Note: Longer cable connections may require lower settings. Select from the following options: 4800bps 9600bps 19200bps 38400bps Note: In the Network mode, Communication Speed function is not available. Menu color select Select color mode to set the menu color.
  • Page 87 5. Using On-Screen Display Monochrome Display time Sets the amount of time a menu is displayed. Select from the following: Manual – Menus stay on screen until the Menu button is pressed again. Auto 5 secs—Menu is displayed for 5 seconds. Auto 15 secs –...
  • Page 88 5. Using On-Screen Display PIN Code Lock Preventing the Unauthorized Use of the Projector on page – 53. Key lock Turn On/Off the Key Lock function for cabinet buttons. Note: This Control Panel Lock does not affect the remote control functions. When the control panel is locked, pressing and holding the Cancel button on the projector cabinet for about 10 seconds.
  • Page 89 5. Using On-Screen Display Network Setting See Network setting on page 82. Standby mode There are two standby modes available: Normal and Power-saving. Power-saving mode allows you to put the projector in the standby condition to consume less power than Normal. Note: Be sure to connect the projector and computer while the projector is in standby mode and before turning on the computer.
  • Page 90 5. Using On-Screen Display PC control This function enables you to select the path for PC control (see PC Control Codes and Cable Connections on page 115). Note: In the Network mode, Communication Speed function is not available. Select from the following: PC control Network...

  • Page 91: Network Setting

    5. Using On-Screen Display Network setting The Network setting tab is accessed by using the Setup/Installation tab and contains the general LAN settings. The following table lists all functions with a description and the default setting. ESCRIPTION DHCP Select either a static IP or DHCP IP setting by selecting the appropriate radio button. IP address Displays the IP address.

  • Page 92: Option

    5. Using On-Screen Display Option The Option tab contains miscellaneous setup menu settings such as Power Management and Default Input Select and can be accessed by using the Setting Menu. The following table lists all functions with a description and the default setting. ESCRIPTION Set this item on to enable the projector to power up when AC plug in.
  • Page 93 5. Using On-Screen Display ESCRIPTION This option switches remote control codes. Remote control Range: Code 1, Code 2, Code 3, Code 4, Code 5, Code 6, Code 7, Code 8 This option turns on or off messages. Message Range: Off or On Set this item to on to have the projector display a message when the air filter needs servicing.
  • Page 94 5. Using On-Screen Display Select from the following: 5 minutes 10 minutes 20 minutes 30 minutes Screen trigger Set Screen trigger to On to enable the projector to automatically lower the projection screen when powering on. When powering off, Screen trigger stops sending a low voltage trigger to the screen controller and the screen goes up. Fan control Fan control is used to set the speed of the internal cooling fan.
  • Page 95 5. Using On-Screen Display Default input select The Default input is the image source that the projector will search for automatically on startup. Last – Uses the most recently used image source. Auto – Auto detects the default image source. Computer1/2/3 –...
  • Page 96 5. Using On-Screen Display Remote control This projector has eight different remote control codes; the factory set normal mode (Code 1) and the other seven codes (Code 2 to Code 8). This switching function prevents remote control operation mixture (jam) when operating several projec- tors or video equipment together.
  • Page 97 5. Using On-Screen Display Filter warning Set Filter warning to have the projector display a message when the air filter needs servicing. The message below shows when this function is activated. Search mode This feature sets the Auto Adjust mode so that the RGB image can be automatically or manually adjusted for noise and stability.

  • Page 98: Information Menu Descriptions And Functions

    5. Using On-Screen Display Information Menu Descriptions and Functions The information menu provides only screens for the quick access of menus. The Information menu contains four distinct tabs. Usage time The Usage Time tab displays information about lamp usage and remaining lamp life. The following table lists all items with a description.

  • Page 99: Input

    5. Using On-Screen Display Input The Input tab displays various source and frequency values at a glance. The following table lists all items with a description. ESCRIPTION Displays the Input Terminal that is presently being used Input name (see Default input select on page 86). Displays the Source name of the signal presently being used Signal (see Option on page 83).

  • Page 100: Network

    5. Using On-Screen Display Network The Network tab displays LAN settings as previously defined (see Network setting on page 82).

  • Page 101: Version

    5. Using On-Screen Display Version The Version tab displays all the version and product details of the projector and associated software (for display only). The following table lists all items with a description. ESCRIPTION Model name Displays Product ID. Serial number Displays projector Serial number.

  • Page 102: Reset Menu Descriptions And Functions

    5. Using On-Screen Display Reset Menu Descriptions and Functions Occasionally, circumstances may require that factory defaults be reset, for demonstration purposes for example, or when components are replaced. The Reset menu contains options for returning settings to the factory default and is accessed by using the Main menu. The following table lists all items with a description.

  • Page 103: Maintenance

    6. Maintenance Cleaning the projector Cleaning the Cabinet Refer to the following guide to clean the projector cabinet. Wipe off dust with a clean dampened cloth. Moisten the cloth with warm water and mild detergent and wipe the cabinet. Rinse all detergent from the cloth and wipe the projector again. CAUTION To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.

  • Page 104: Cleaning The Filters

    6. Maintenance Cleaning the Filters The projector uses three filters to keep the fans free of dust and other particles, and should be cleaned every 500 hours of operation. In dusty environments, it is recommended to clean the filters more frequently. If the filter is dirty or clogged, your projector may overheat.
  • Page 105 6. Maintenance The rear filter can be accessed as shown. Once the filters are cleaned, please reset the filter hours by using the Clear filter time option in the Reset Menu Descriptions and Functions on page 93. Note: Using the projector without the air filter fitted inside, dirt and dust are sucked into the projector, causing fail- ure.

  • Page 106: Replacing Consumable Parts

    6. Maintenance Replacing Consumable Parts During the course of normal usage, consumable parts become worn out resulting in reduced performance. The following guides detail how to replace the various consumable parts within the projector quickly and safely. • Before replacing any of the parts, please take note of the following: •...
  • Page 107 6. Maintenance Insert replacement foam and press down firmly. Replace the filter covers by pushing gently in the direction shown. Once the filters are replaced, please reset the filter hours by using the Clear filter time option in the Reset Menu Descriptions and Functions on page 93.

  • Page 108: Replacing The Lamps

    6. Maintenance Replacing the Lamps When a lamp reaches the end of it’s usable life, the following message is displayed. Replace the lamp. The projection lamps should be replaced when they burn out. They should only be replaced with a certified replacement part, contact your local dealer if unsure.
  • Page 109 6. Maintenance Check the lamp number to be replaced by using Information Menu. Turn off the projector and disconnect the AC plug. Allow the projector to cool for at least 60 minutes. Loosen the screw on the lamp cover (A), and remove the lamp cover as shown (B).

  • Page 110: Resetting The Lamp Time Counter

    6. Maintenance Resetting the Lamp Time Counter After replacing the lamp(s), the lamp hour counter(s) should be reset to zero. Refer to the following guide: Press the Menu button on the OSD control panel or Remote Control to open the Main menu. Press the ▲or▼...

  • Page 111: Appendix

    7. Appendix Troubleshooting Indicator Messages Several indicator messages are used by the projector to alert users of problems with setup or internal parts. The LEDs on the top surface of the projector show the status of the WARNING and lamp 1/2 as well as the general working order of the projector through the WARNING LED (see OSD Controls and Status LEDS on page for location).
  • Page 112 7. Appendix The LAMP LEDs LED C LED S ROJECTOR TATUS ONDITION EQUENCE ROJECTOR ONDITION Lamp off Lamp off 0.5 secs on End of the lamp life Red blink Replace lamp 0.5 secs off Red 1 time blink (re- 0.5 secs on No lamp ERROR peatedly)

  • Page 113: Common Problems And Solutions

    7. Appendix Common Problems and Solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance. Often the problem is something as simple as a loose connection. Check the following before proceeding to the problem- specific solutions.

  • Page 114: Image Problems

    7. Appendix Image Problems Problem: No image appears on the screen 1. Verify the settings on your notebook or desktop PC. 2. Turn off all equipment and power up again in the correct order. Problem: The image is blurred 1. Adjust the Focus on the projector. 2.

  • Page 115: Remote Control Problems

    7. Appendix Problem: The lamp goes off 1. Power surges can cause the lamp to turn off. Press the power button twice to turn off the projector. When the Power LED is orange, press the power button. 2. Replace the lamp module. 3.

  • Page 116: Specifications

    8. Specifications Projector Specifications This section provides technical information about the projector's performance. Optical Specifications ESCRIPTION ® Projection system Single DLP chip, 4 segment color wheel Resolution 1280 x 768 pixels* (up to UXGA @ 60 Hz, up to SXGA+ @ 60 Hz on DVI-D) Lamp 260 W AC (230 W in Eco mode), Dual lamp system 50"...

  • Page 117: Electrical Specifications

    8. Specifications Electrical Specifications ESCRIPTION 1 Analog RGB (Mini D-Sub 15P), 1 Analog RGB R/Cr, G/Y, B/Cb, H, V (BNC x 5), 1 Digital RGB (DVI-D 24P), 1 Component Y, Cb/Pb, Cr/Pr Inputs (RCA x 3), 1 Component (Mini D-Sub 15P) shared with COMPUTER 1 IN, 1 S-Video (Mini DIN 4P), 1 Video, 3 Stereo Mini Audio, 2 (L/R) RCA Audio, 1 Remote Control (Stereo Mini) Outputs...

  • Page 118: Mechanical Specifications

    8. Specifications ESCRIPTION 655W in Dual Lamp Normal mode / 580W in Dual Lamp Eco mode 350W in Single Lamp Normal mode / 315W in Single Lamp Eco mode Power Consumption < 30W in Standby mode Normal < 5W in Standby mode Power saving Mechanical Specifications ESCRIPTION 19.9"...

  • Page 119: Optional Parts

    8. Specifications Optional Parts The parts listed below are optionally available. When ordering those parts, specify the item name and Model No. to the sales dealer. Standard Zoom Lens : LNS-S40 Long Zoom Lens : LNS-T40 Ultra Long Zoom Lens : LNS-T41 Short Zoom Lens : LNS-W40...

  • Page 120: Cabinet Dimensions

    8. Specifications Cabinet Dimensions...

  • Page 121: Pin Assignments Of Mini D-Sub 15 Pin Input Connector

    8. Specifications Pin Assignments of Mini D-Sub 15 Pin Input Connector Signal Levels Video signal: 0.7Vp-p (Analog) Sync signal: TTL level RGB S UMBER IGNAL NALOG IGNAL Green or Sync on Green Blue Ground Ground Red Ground Cr Ground Green Ground Y Ground Blue Ground Cb Ground...

  • Page 122: Compatible Input Signal List

    8. Specifications Compatible Input Signal List The following table shows compatible signal types, their resolution and frequency refresh rates. Horizontal: 15kHz, 31kHz to 90 kHz Vertical: 50 Hz to 85 Hz H-Sync V-Sync Signal Resolution Component Video [KHz] [Hz] 640 x 350 31.5 70.1 Ο...
  • Page 123 8. Specifications 1366 x 768 48.36 Ο Ο 1376 x 768 48.36 Ο Ο 1400 x 1050 64.7 60.0 Ο Ο 1400 x 1050 65.3 60.0 Ο Ο 1400 x 1050 82.3 75.0 Ο Ο 1440 x 900 55.9 60.0 Ο...

  • Page 124: Pc Control Codes And Cable Connections

    8. Specifications PC Control Codes and Cable Connections This projector provides a function to control and monitor the projector's operations by using the RS-232C serial port. Connect a RS-232C serial cross cable to SERIAL PORT IN on the projector and serial port on the PC.

  • Page 125: Status Read Command Table

    8. Specifications Status Read Command Table OMMAND UNCTION Status Read Temperature Read PC Control Connector (DIN-9P) Note: 1. Pin 1, 4, 6 and 9 are not used. 2. Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify the cable connection.

  • Page 126: Screen Trigger

    8. Specifications Screen Trigger When the projector is powered ON the screen trigger output sends a low voltage trigger to the screen controller and the screen will go down. When the projector is powered OFF the screen trigger stops sending a low voltage trigger to the screen controller and the screen will go up.

  • Page 127: Operation Using Http Browser

    8. Specifications Operation Using HTTP Browser Overview The use of HTTP server functions will allow control of the projector from a web browser without the installation of special software. Please be sure to use “Microsoft Internet Explorer 4.x” or a higher version for the web browser. (This device uses “JavaScript”...

  • Page 128: Configuring Network Settings

    8. Specifications Configuring Network Settings The Network Settings screen is displayed as follows: http:// <the projector's IP address> /lanconf.html Domain Host Name: Type in a hostname. Up to 60 alphanumeric characters can be used. Domain Name: Type in domain name of the network connected to the projector. Up to 60 alphanumeric characters can be used. Apply: Click to reflect the entries.
  • Page 129 8. Specifications Test Mail Send a test mail to check if your settings are correct. Click to “Execute” to enable this feature. Test Mail Status Button: Click to display the test result. Sample of a message sent from the projector: Projector Name: X X X X Lamp 1 or 2 Hours Used: xxxx [H] The lamp is at the end of its usable life.

  • Page 130: Structure Of The Http Server

    8. Specifications Structure of the HTTP Server Once the projector is connected to a network and configured correctly, the following screen is displayed through the web browser. http:// <the projector's IP address> /index.html UNCTION ETTING ESCRIPTION Power Panel This controls the power to the projector Volume Panel ▲...
  • Page 131 8. Specifications UNCTION ETTING ESCRIPTION Input Select Panel Computer1 – Switches to the COMPUTER 1 IN connector This switches the input connector of the projector Computer2 – Switches to the COMPUTER 2 IN connector Computer3 – Switches to the COMPUTER 3 IN connector Component –...

  • Page 132: 15 Pin Gpio Control

    8. Specifications 15 Pin GPIO Control Type: 15Pin D-SUB black female type HORT UNCTION SHORT EXTERNAL CONTROL MODE ON OPEN EXTERNAL CONTROL MODE OFF POWER ON SHORT POWER OFF OPEN PICTURE MUTE ON SHORT PICTURE MUTE OFF OPEN SOUND MUTE ON SHORT SOUND MUTE OFF OPEN...

  • Page 133: Troubleshooting Check List

    9. Troubleshooting Check List Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by referring to the Troubleshooting section on page of your user’s manual. This checklist below will help us solve your problem more efficiently.
  • Page 134 WARNING Indicator: Steady light Orange Green Flashing light [ ] cycles Remote control model number: Signal cable Computer SANYO standard or other manufacturer’s cable? Manufacturer: Model number: Length: inch/m Model number: Distribution amplifier Notebook PC / Desktop Model number:...
  • Page 135 KW3AL SANYO Electric Co., Ltd.

This manual is also suitable for:

Pdg-dwt50kl

Table of Contents