Advertisement
WD0046-04-08.qxd
21/7/08
10:54 am
Page 1
INSTRUCTIONS AND GUARANTEE
W
'N D
V
& B
ET
RY
ACUUM
LOWER
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE
RETAIN FOR FUTURE REFERENCE
EARLEX LTD. WILL ACCEPT NO RESPONSIBILITY FOR THE USE OF THIS PRODUCT IF USED FOR
ANY OTHER PURPOSES THAN THOSE DETAILED HEREIN.
Advertisement
Table of Contents
Related Manuals for Earlex COMBIVAC
Summary of Contents for Earlex COMBIVAC
- Page 1 INSTRUCTIONS AND GUARANTEE ‘N D & B ACUUM LOWER PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE RETAIN FOR FUTURE REFERENCE EARLEX LTD. WILL ACCEPT NO RESPONSIBILITY FOR THE USE OF THIS PRODUCT IF USED FOR ANY OTHER PURPOSES THAN THOSE DETAILED HEREIN.
- Page 2 Deluxe Floor Head accessory (WDACC2). This includes a brush attachment for use on carpets. IF YOU HAVE ANY PROBLEMS WITH YOUR COMBI VAC OR IF YOU BELIEVE A PART IS MISSING, DO NOT RETURN TO STORE. PLEASE CONTACT EARLEX LTD ON 01483 454666.
-
Page 3: Unpacking And Setting Up
WD0046-04-08.qxd 21/7/08 10:54 am Page 3 COMPONENTS The following components are included in the kit (as illustrated below) WD0001 Recovery Tank WD0036 Crevice Tool WDACC4 Extension Tubes x 2 WD0037 Floor Head WD0029 Paper Filter WD0045 Castors x 4 WD0030 Foam Filter WD0048 Hose... -
Page 4: Filter Installation
Failure to do this will invalidate the guarantee. A clean filter is essential for this cleaner to operate efficiently. If the filter becomes clogged or damaged or fails to operate you must fit an Earlex replacement. Details are supplied with the cleaner. Dry Filter Part No WD0029, Foam Filter Part No WD0030. -
Page 5: Filter System
WD0046-04-08.qxd 21/7/08 10:54 am Page 5 FILTER SYSTEM The cleaner is supplied with 2 filters, one is made of foam and the other of paper. It is extremely important that you use these correctly. DRY PICK UP The foam filter requires to be fitted. To install this, slide the foam filter down over the float cage until it touches the top - see illustration. -
Page 6: Operation
5) Check and clean any blockages within the unit. 6) Replace motor housing, plug in and continue as before. BLOWER FUNCTION 1) The CombiVac can be used as a powerful blower by inserting the hose into the outlet on the motor housing. -
Page 7: Troubleshooting
Tel: 01483 454666 Fax: 01483 454548 email:enquiries@earlex.co.uk Opening Hours: Monday-Friday 08.30 -17.00 (Excluding Bank Holidays) ACCESSORIES AND SPARE PARTS A range of spare parts are available for the CombiVac . To order please contact our helpline on 01483 454666. Opening Hours: Monday-Friday 08.30-17.00 (Excluding Bank Holidays) WDACC2 - Deluxe Floor Head with hard floor, brush and squeegee attachments. -
Page 8: Mains Connection
Whilst every possible care is taken by Earlex to ensure that our products leave the factory in good working order, Earlex cannot under any circumstances accept liability for problems or damage caused by their subsequent use.
Need help?
Do you have a question about the COMBIVAC and is the answer not in the manual?
Questions and answers
How do I change the filter
To change the filter on the Earlex COMBIVAC:
1. For Dry Pick-Up:
- Ensure the foam filter is dry.
- Slide the foam filter down over the float cage until it touches the top.
- Carefully install the paper filter over the foam filter.
- Secure the paper filter with the rubber band, ensuring it fully covers the foam filter up to the shoulder of the molding.
- Periodically brush dirt off the paper filter with a soft brush.
2. For Wet Pick-Up:
- Remove the paper filter (do not use it for wet pick-up).
- Use only the foam filter.
- Clean the foam filter with soapy water when necessary and dry it thoroughly before using it again.
3. Maintenance:
- Periodically replace the paper filter.
- Wash the foam filter with soapy water, rinse, and dry before reinstalling.
- Ensure the filters are clean and undamaged for proper operation.
This answer is automatically generated
How to get it into suction mode
To switch the Earlex COMBIVAC to suction mode:
1. Ensure the motor housing is clipped onto the base correctly, with the air outlet opposite the vacuum inlet hose.
2. Assemble the hose by connecting it to the recovery tank, making sure it is properly secured.
3. Attach an extension tube and either the floor head or crevice tool if needed.
4. Unwind the mains lead fully and plug it into a power source.
5. Switch the unit on to begin suction operation.
This answer is automatically generated