Table of Contents
Advertisement
INTRODUCTION
Dear Customer,
Thank you for having chosen one of our products. We hope
that you will get complete satisfaction from using your new
machine and that it will fully meet all your expectations.
This manual has been written to help you become familiar with
the machine and use it safely and efficiently. Do not forget that
it is an integral part of the machine, so keep it close at hand
for future reference and pass it on to the purchaser if you sell
the machine.
This new lawn tractor has been designed and built in compli-
ance with current standards, and is safe and reliable if used for
cutting grass following the instructions given in this manual
(proper usage). If you use the machine in any other way or
ignore the instructions for safe use, maintenance and repair, it
is considered "incorrect usage". In this case, the warranty is
automatically voided and the Manufacturer is not held respon-
sible for damage or injury to oneself or others.
Since we regular improve our products, you may find slight dif-
ferences between your machine and the descriptions con-
tained in this manual. Modifications can be made to the
machine without notice and without the obligation to update
the manual, although the essential safety and function charac-
teristics will remain unaltered. If in doubt, do not hesitate to
contact your dealer. And now enjoy your work!
AFTER-SALES SERVICE
This manual gives all the necessary instructions for using the
machine and carrying out basic maintenance.
Any adjustments or maintenance operations not described
in this manual must be carried out by your Dealer or a spe-
cialized Service Centre. Both have the necessary knowl-
edge and equipment to ensure that the work is done cor-
rectly without affecting the safety of the machine.
If you wish, you can ask your dealer to prepare a maintenance
programme personalised to your needs. This will help you
keep your new purchase in peak performance and maintain its
value over time.
EN
1
Advertisement
Table of Contents
Related Manuals for Mountfield 1538M SD
Summary of Contents for Mountfield 1538M SD
- Page 1 INTRODUCTION Dear Customer, AFTER-SALES SERVICE Thank you for having chosen one of our products. We hope This manual gives all the necessary instructions for using the that you will get complete satisfaction from using your new machine and carrying out basic maintenance. machine and that it will fully meet all your expectations.
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1. SAFETY ..........................3 Regulations for using the machine safely 2. IDENTIFICATION OF THE MACHINE AND COMPONENTS ..........7 How to identify the machine and its main components 3. UNPACKING AND ASSEMBLY ..................9 How to remove the packing and assemble loose parts 4. -
Page 3: Safety
1. SAFETY 1.1 HOW TO READ THE MANUAL The symbol “ ” refers to another part of the manual where further information can be found. Some paragraphs in the manual containing important informa- tion regarding safety and operation are emphasized in the fol- NOTE lowing ways: Positions on the... - Page 4 3) Never mow while people, especially children, or pets – if you spill petrol, do not start the engine and move the are nearby. machine away from the area of spillage. Do not create any 4) Keep in mind that the operator or user is responsible for source of ignition until the petrol vapours have evaporated;...
- Page 5 – do not turn sharply. Use care when reversing; building where fumes may reach an open flame or spark. – use counterweight(s) or wheel weights whenever advised in 3) Allow the engine to cool before storing in any enclosure. the instructions manual. 4) To reduce fire hazards, keep the engine, silencer, battery 7) Disengage the blades before crossing surfaces other than compartment and petrol storage area free of grass, leaves, or...
- Page 6 1.3 SAFETY LABELS Danger of cutting yourself. Blades in movement. Do not put hands or feet near or Your machine must be used with care. This is why labels with under the opening of the cutting plate. illustrations have been placed on the machine, to remind you of the main precautions to take during use.
-
Page 7: Identification Of The Machine And Components
2. IDENTIFICATION OF THE MACHINE AND COMPONENTS 2.1 IDENTIFICATION OF THE MACHINE 2.2 IDENTIFICATION OF MAIN COMPONENTS The label located near the battery housing has the essential The main components of the machine have the following func- data of each machine. tions: Acoustic power level according to directive... - Page 8 15. Battery: provides the energy for starting the engine. Its specifications and regulations for use are described in a specific manual. 16. Driving seat: this is where the machine operator sits. It has a sensor connected to safety devices for detecting the presence of the operator.
-
Page 9: Unpacking And Assembly
3. UNPACKING AND ASSEMBLY For storage and transport purposes, some components of the NOTE To prevent damage to the cutting deck, machine are not installed in the factory and have to be assem- raise it to its maximum height and take utmost care when bled after unpacking. - Page 10 3.4 ASSEMBLY AND CONNECTING THE BATTERY The battery (1) is housed under the seat and secured by a spring (2). First connect the red wire (3) to the positive pole (+) and then the black wire (4) to the negative pole (–), using the screws supplied as shown.
- Page 11 3.5 FITTING THE STONE-GUARD Inside the stone-guard (1), fit the spring (2) by inserting the ter- minal (2a) into the hole and turning it so that both the spring (2) and the terminal (2a) are securely positoned in their seat- ings.
-
Page 12: Controls And Instruments
4. CONTROLS AND INSTRUMENTS 4.21-4.31 – The «CHOKE» position enriches the mixture so must only be used for the time necessary when starting from cold. 4.31 – When moving from one area to another, put the lever in a position between «SLOW» and «FAST». –... - Page 13 There are two positions: on the label), which correspond to various heights between 3 and 8 «A» = Brake off – To go from one position to another, move the lever sideways «B» = Brake on and put it back in one of the stop notches.
- Page 14 neutral position «N», and reverse the pedal, the speed of the machine increases. 4.22 «R». – Reverse is engaged by pressing the pedal with the heel towards «R». – The pedal automatically goes into neutral «N» when To go from one speed to another, released.
-
Page 15: How To Use The Machine
5. HOW TO USE THE MACHINE 5.1 SAFETY RECOMMENDATIONS 5.2 WHY THE SAFETY DEVICES CUT IN DANGER! The machine must only be used for The safety devices work in two ways: the purpose for which it was designed (cutting grass). –... -
Page 16: Preliminary Operations Before Starting Work
5.3 DIRECTIONS BEFORE STARTING WORK Before starting to mow, it is necessary to carry out several checks and operations to ensure you can work efficiently and in maximum safety. 1,5 bar (13 x 5,00-6) 1,2 bar 1,0 bar (15 x 5,00-6) 5.3.1 Seat adjustment To change the seat position, loosen the four fixing bolts (1) and slide it along the slots. - Page 17 Always check that the inner spring of the stone-guard (1) works properly, whilst keeping it securely lowered. Refuel using a funnel, but do not completely fill the tank. The tank's capacity is about 6.5 liters. DANGER! Refuelling should be carried out in an 5.3.5 Checking machine safety and efficiency open or well-ventilated area with the engine off.
-
Page 18: Using The Machine
5.4 USING THE MACHINE not insist as you can risk running the battery flat and flooding the engine. Turn the key to «OFF», wait for a few seconds 5.4.1 Starting and then repeat the operation. If the malfunction persists, refer to the engine manual and chapter «7» in this manual. DANGER! The engine must be started in an open or well-ventilated area! ALWAYS REMEMBER THAT... - Page 19 brake. Slowly release the pedal to shift from «brake» to 5.4.4 Reverse «clutch», thus operating the rear wheels ( 4.21). IMPORTANT Reverse must be engaged only when the WARNING! The pedal has to be released grad- machine has stopped moving. ually, as a sudden engagement may cause the vehi- cle to tip over and the driver to lose control.
- Page 20 cutting deck drags over irreg- to the amount of grass being cut, you will not be able to mow ular ground. the grass well. The four different heights of Disengage the blades and raise the cutting deck as high as the wheels allows you to possible whenever you need to get past an obstacle.
- Page 21 5.4.8 Cleaning the machine After use, clean the outside of the machine. Clean the plastic parts of the body with a damp sponge using water and detergent, taking care not to wet the engine, the electrical parts or the electronic circuit board located under the dashboard.
-
Page 22: Using On Slopes
5.4.10 Board protection fuse The electronic board is fitted with a fuse which breaks the cir- cuit if there is a fault or short circuit on the electrical system. The intervention of the fuse causes the engine to stop; before replacing the fuse ( 6.3.5) try to find and remove the cause of the fault to prevent it from happening again. -
Page 23: Transporting The Machine
cock (if fitted), lower the cutting deck, apply the parking DANGER! Start moving forwards very carefully brake and fasten the machine securely with ropes or on sloping ground to prevent the risk of tipping over. chains to the hauling device. Reduce the forward speed before going on a slope, par- ticularly downhill. - Page 24 The best height of the grass on a well-kept lawn is approx. 4-5 cm. With one cut, you do not need to remove more than a third of the total height. If the grass is very tall, it should be cut twice in a twenty- four hour period - the first time with the blades at maxi- mum height, possibly reducing the cutting width, and the second cut at the desired height.
-
Page 25: Maintenance
6. MAINTENANCE 6.1 SAFETY RECOMMENDATIONS The boxes at the side are for you to mark the date or number of working hours at which the intervention was made. WARNING! Before cleaning or doing mainte- Operation Hours Completed (Date or Time) nance work, take out the ignition key and read the rele- 1. - Page 26 6.2.1 Engine The machine battery must always be charged: – before using the machine for the first time after purchase; IMPORTANT Follow all the instructions in the engine – before leaving the machine disused for a long period; manual. – before starting up the machine after a long period of disuse. To empty the oil from Carefully read and observe the battery recharging instructions the engine, hold the...
-
Page 27: Interventions On The Machine
“CB01” maintenance battery-charger supplied (if included) or your Dealer who will test and make the necessary adjustments available on request ( 8.2). to the alignment of the cutting deck. IMPORTANT This connector must only be used for 6.3.2 Replacing wheels connection to the “CB01”... - Page 28 6.3.3 Replacing and repairing the tyres 6.3.5 Replacing a fuse The tyres are «Tubeless» and so all punctures must be repaired The machine is fitted with fuses (1) with different capacities by a tyre repairer following the procedures required for this and functions.
-
Page 29: Information For Service Centres
6.4 INFORMATION FOR SERVICE CENTRES Below is a list of specifications for machine adjustments and instructions for dismantling and replacing the blades. WARNING! These operations must be carried out by a specialized Centre only. Remove the ignition key before doing any adjustments or maintenance. 6.4.1 Adjustments Position Element... - Page 30 6.4.2 Dismantling, replacing and remounting the blades WARNING! Always wear work gloves when handling the blades. WARNING! Damaged or bent blades must always be replaced; never try to repair them! ALWAYS USE ORIGINAL BLADES BEARING THE SYMBOL ! Make sure the blades are correctly balanced. 1.
-
Page 31: Troubleshooting
7. TROUBLESHOOTING PROBLEM LIKELY CAUSE SOLUTION 1. With the key on "START" the starter motor Turn the key to pos. «OFF» and look for the does not run causes: – conditions are not met to allow starting – check that the conditions allowing starting are met ( 5.2.a) –... - Page 32 PROBLEM LIKELY CAUSE SOLUTION 5. The motor shuts down whilst working – the safety devices have cut in – check that the conditions allowing starting are met ( 5.2.b) – fuse blown (10 A) – replace the fuse (10 A) ( 6.3.5) 6.
-
Page 33: Accessories On Request
8. ACCESSORIES ON REQUEST 1. “MULCHING” KIT 4. FRONT BUMPER KIT It finely chops the grass cut- This protects the front sec- tings and leaves it on the tion of the machine. lawn, as an alternative to lat- eral ejection. 2. -
Page 34: Specifications
9. SPECIFICATIONS Electrical system ............... 12 V Battery ................18 Ah Front tyres .............. 13 x 5.00-6 or ................ 15 x 5.00-6 Rear tyres ............... 18 x 8.50-8 Front tyre pressure tyres 13 x 5.00-6 ............1.5 bar tyres 15 x 5.00-6 ............1.0 bar Rear tyre pressure ............
Need help?
Do you have a question about the 1538M SD and is the answer not in the manual?
Questions and answers
How do you put the muncher in
engine does not crank