Delta ShopMaster DP200 Instruction Manual
  1. Manuals
  2. Brands
  3. Delta Manuals
  4. Drill
  5. ShopMaster DP200
  6. Instruction manual

Delta ShopMaster DP200 Instruction Manual

Delta 10" bench drill press instruction manual dp200
Hide thumbs
Table of Contents

Advertisement

Quick Links

10" Bench Drill Press
(Model DP200)
PART NO. 906770 -
07-01-02
Copyright © 2002 Delta Machinery
To learn more about DELTA MACHINERY
ESPAÑOL: PÁGINA 17
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
1-800-223-7278 (
1-800-463-3582).
please call
In Canada call

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ShopMaster DP200 and is the answer not in the manual?

Questions and answers

Related Manuals for Delta ShopMaster DP200

Summary of Contents for Delta ShopMaster DP200

  • Page 1 10" Bench Drill Press (Model DP200) PART NO. 906770 - 07-01-02 Copyright © 2002 Delta Machinery To learn more about DELTA MACHINERY ESPAÑOL: PÁGINA 17 visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, 1-800-223-7278 ( 1-800-463-3582).

  • Page 2: General Safety Rules

    If you have any questions relative to a particular application, DO NOT use the machine until you have first contacted Delta to determine if it can or should be performed on the product.
  • Page 3 TABLE. Do not attempt to drill a workpiece that does not have a flat surface against the table. Prevent the workpiece from rotating by clamping it to the table or by securing it against the drill press column. SAVE THESE INSTRUCTIONS.

  • Page 4: Motor Specifications

    A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug.

  • Page 5: Extension Cords

    Ampere OPERATING INSTRUCTIONS FOREWORD Delta ShopMaster Model DP200 is a 10" bench drill press with a 1/4 H.P. motor, and a flexible work lamp. The Delta ShopMaster Model DP200 can handle most types of drill press operations. UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s).
  • Page 6 1 - Drill Press Head and Motor 2 - Table Raising and Lowering Handle 3 - Table Clamp 4 - Chuck 5 - Chuck Key 6 - Pinon Shaft Handles (3) 7 - M8x1.25x125mm Carriage Head Screws (2), M8 Flat Washers (2), M8.1 Lock Washers (2), M8x1.25 Hex Nuts...
  • Page 7 WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. 1. Assemble the column (A) Fig. 3, to the base (B) using the four screws, three of which are shown at (C).
  • Page 8 4. Slide raising rack (F) Fig. 7, table and table bracket onto drill press column, as shown. Make sure bottom of raising rack (F) Fig. 8, is inside the flange (J) on drill press base. 5. Re-assemble ring (E) Fig. 9, which was removed in STEP 1.
  • Page 9 7. Thread stud on clamp handle (M) Fig. 12, into hole in rear of table bracket, as shown. 8. Place the drill press head (N) Fig. 13, onto the column as far as it will go. Align head (A) Fig. 13A, to table (B), and base (C).

  • Page 10: Operating Controls And Adjustments

    STARTING AND STOPPING DRILL PRESS The switch (A) Fig. 18, is located on the front of the drill press head. To turn the drill press “ON” move the switch up to the “ON” position. To turn the drill press “OFF”...

  • Page 11: Locking Switch In The "Off" Position

    The reflector track type light bulb should not extend below the lamp shade. TABLE ADJUSTMENTS 1. The table can be raised or lowered on the drill press column by loosening the table clamp (A) Fig. 20, and turning the table raising and lowering handle (B) Fig. 21.

  • Page 12: Spindle Speeds

    (B) Fig. 26, and pivoting the motor (D) toward the front of the drill press. 4. While holding the motor toward the front of the drill press, position the belt (C) on the desired steps of the motor and spindle pulleys, as shown in Fig. 26.

  • Page 13: Drilling Holes To Depth

    Then tighten lock screw (A). Return the spindle to the up position. 4. Place the material to be drilled on the drill press table. Raise the drill press table until the material to be drilled just touches the drill bit.

  • Page 14: Operation

    Your drill press is to be used with drill bits with a shank of 1/2" or less in diameter. The following will give the inexperienced operator a start on common drill press operations. Use scrap material for practice to get a feel of the machine before attempting regular work.

  • Page 15: Correct Drilling Speeds

    Do not use hand bits which have a screw tip; at drill press speeds they turn into the wood so rapidly as to lift the work off the table and whirl it.

  • Page 16: Parts, Service Or Warranty Assistance

    1-800-223-7278 (In Canada call 1-800-463-3582). Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection.

Table of Contents

Save PDF