Related Manuals for Fuji Spray SUNLESS salonTAN Series
Summary of Contents for Fuji Spray SUNLESS salonTAN Series
- Page 1 USER MANUAL TAN TURBINES salonTAN Series ™ studioTAN Series ™ soloTAN Series ™ APPLICATORS T-PRO 4200 FT-5 TAN 7350...
- Page 2 Thank you for purchasing your Fuji Spray Sunless spray tanning system. This product has been designed to provide the efficient application of tanning solution products. Please read this user manual to understand how to operate your spray tanning system and to accomplish a flawless tan with every application.
- Page 3 Table of Contents Applicator Details - Box Contents Safety Precautions 3 - 5 Applicator Diagrams 6 - 11 T-PRO 4200 FT-5 TAN 7350 Getting Started 12 - 13 Hose Connection Flush Applicator Turbine Breaker Switch Cup Holder Installation Applicator Use 14 - 17 FT-5 Applicator Features Spray Patterns...
- Page 4 APPLICATOR DETAILS - BOX CONTENTS The below are “bleeder” style applicators. Air will continuously flow out of the front of the applicator as soon as the turbine is turned on. T-PRO 4200 BOTTOM FEED T-PRO 4200 Bottom Feed Applicator installed with 0.8mm Air Cap Set and 250cc Cup 2.
- Page 5 SAFETY PRECAUTIONS Please read these instructions carefully before using the equipment. Grounding This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug.
- Page 6 Toxic Fluid or Fumes Hazard Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed. • Always wear appropriate gloves and eye protection. • Always wear a mask. Read all instructions of the respirator or mask to ensure that it will provide the necessary protection against the inhalation of harmful vapors.
- Page 7 Equipment Misuse Hazard Misuse of equipment can cause serious injury or death. • Do not operate or spray near children. Keep children away from equipment at all times. • Do not overreach or stand on an unstable support. Keep effective footing and balance at all times.
- Page 8 APPLICATOR DIAGRAMS T-PRO 4200 Applicator T-PRO 4200 Applicator Bottom Feed Cup...
- Page 9 Item Part Name Note 5201 Collar 5302 Air Cap 5303 Fluid Nozzle 5204 Air Diffuser 5205 Air Diffuser Seal 5207 Air Divider with Seal (5206) 5221 Fluid Knob 5219 Needle 5220 Needle Spring 5225 Fan Pattern Control Knob 5229 Hose Connector 5209 Needle Packing 5210...
- Page 10 FT-5 Applicator Cup Sizes 150cc Cup 250cc Cup The FT-5 Applicator comes with 2 cup sizes. To change to a different cup size, please refer to the instructions on page 14.
- Page 11 Item Part Name Note 7601 Collar 7602 Air Cap 7603 Fluid Nozzle 7604 Air Diffuser 7605 Air Divider 7606 Needle Packing Nut 7607 Needle Packing 7608 Needle Packing Spring 7610 Pattern Control Locking Screw 7611 Pattern Control Knob 7612 Pattern Control Retaining Clip 7613 Air Deflector 7615...
- Page 12 TAN 7350 Applicator TAN7350 Applicator Bottom Feed Cup...
- Page 13 Item Part Name Note 2301 Collar 2302 Air Cap 2306 Fluid Nozzle 2304 90 Degree Nipple 2303 Diffuser 2338A Pattern Control Knob 2307 Fluid Knob 2314 Needle Assembly 2309 Needle Spring 2310 Handle 2311 Hose Connector 2312 Needle Packing 2313 Needle Packing Nut 2330 Trigger Pin...
- Page 14 GETTING STARTED Hose Connection Connect the end of the hose (female connector) to the turbine air outlet located on the front of the turbine. This is a simple threaded connector. Hand-tight is enough – it is not necessary to use a wrench.
- Page 15 CUP HOLDER INSTALLATION studioTAN and salonTAN Cup Holder Attachment ™ ™ The two holes on the top of the cup holder require the black screws and washers included with this hardware. These screws fit into threaded inserts in the metal case. Do not over-tighten. The single silver-colored screw must be installed to the single side hole of the cup holder.
- Page 16 APPLICATOR USE FT-5 Applicator Features Selecting a Cup Size The FT-5 Applicator comes with 2 cup sizes: 150cc Cup This cup is pre-installed on the FT-5 Applicator. It is ideal for smaller tanning sessions for 1-2 tans. 250cc Cup This cup is included with the FT-5 Applicator. It is ideal for larger tanning sessions for 3-4 tans.
- Page 17 Cup Removal and Lids Removing and Attaching Cup To remove the cup, hold it firmly and turn it counter- clockwise. If fluid is in the cup, it is best to do this on a flat surface to avoid spilling. Remember not to fill the cup past the fill line as indicated. To reattach the cup, turn the cup clockwise until tight and properly sealed.
- Page 18 Spray Patterns Choosing A Pattern The pattern orientation can be adjusted by changing the angle of the air cap. A spray pattern width can be chosen by adjusting the pattern control. This pattern is used This pattern is used when spraying when spraying side up and down.
- Page 19 Fluid Output Selecting The Fluid Output The rear dial on all of the applicators is the fluid control. This setting will allow you to change how much tanning solution comes out of the applicator when the trigger is fully pressed. To adjust the fluid output, turn the fluid control knob on the rear of the applicator.
- Page 20 SPRAYING TECHNIQUE When spraying, move the applicator at a medium, steady speed, keeping the distance of the applicator the same throughout the spray application. If you wish to change the direction of the spray pattern, rotate the position of the aircap (see page 16) rather than tilting the applicator to its side.
- Page 21 CLEANING AND MAINTENANCE Basic Applicator Cleaning Tanning solution should not be left in the cup attached to the applicator overnight. It can dry and harden, leaving a film throughout the applicator’s fluid passages. Over time, the fluid passages can become clogged. To prevent this, spray soapy water through the applicator periodically.
- Page 22 Advanced Applicator Cleaning Do not soak the whole applicator in any liquid. This is never necessary or advisable. FT-5 Applicator • Remove the fluid knob (#20), spring (#19), and needle (#18) from the rear of the applicator. • At the front of the applicator, remove collar (#1) and air cap (#2). •...
- Page 23 • There is a locating pin on the back side of the diffuser. This pin must be placed into the matching hole in the air divider (#6), and into another matching hole in the gun body. The matching hole of the gun body is located at a 12 o’clock position.
- Page 24 Turbine Maintenance The only regular maintenance required on the turbine is the cleaning and replacing of the filter(s). The turbines have either one or two filters. Remove based on the instructions below and wash the filter in warm soapy water. Dry before replacing back in the turbine.
- Page 25 soloTAN™ Filter #7455 2) Pull the grill directly away from the 1) Pull the grip tabs on both sides of main unit to separate. the grill outwards to release it. 4) Clean and let dry or replace the foam 3) Carefully remove the foam filter filter, and replace it in the grill.
- Page 26 TROUBLESHOOTING 1) Solution coming out from nozzle without trigger engaged FT-5 Applicator • Check and clean fluid nozzle (#3). If damaged, it will require replacement • Half fill the solution cup with water • Connect the applicator to the hose and switch the turbine on •...
- Page 27 2) Leaking from needle packing nut T-PRO 4200 Bottom Feed and TAN 7350 Applicator The needle packing nut (#13) may be too loose. It needs to be tightened. • Half fill the solution cup with water • Connect the applicator to the hose and switch the turbine on •...
- Page 28 4) Uneven pattern when spraying • Check and clean nozzle • Check and clean air cap. Use a soft cleaning brush. Never use metal objects to clean holes in the air cap 5) Poor spray pattern • Damaged needle or fluid nozzle – This will require replacement •...
- Page 29 10) Turbine keeps shutting off at the breaker switch • Check the filter(s) is clean and in place properly • Check the air hose for any kinks that may restrict the air flow • The turbine is overheating due to over usage. Leave the turbine off for a few minutes to cool down.
- Page 30 Fuji Spray Limited Warranty ® Fuji Industrial Spray Equipment Ltd. (“Fuji”) provides a limited warranty on the product to the original purchaser effective from the date of purchase against defects in materials and workmanship, for the time periods as follows: Turbines salonTAN 2 years...
- Page 31 Declaration of Conformity Manufacturer: Fuji Industrial Spray Equipment Ltd. 800 Alness Street, Toronto, ON Canada M3J 2H5 Declares that the product: HVLP Turbine Product name(s): soloTAN , studioTAN , salonTAN ™ ™ ™ Model(s): 2175, 6175, 6100, 2100, 6150, 2150, 3500, 3550, 3575 Conforms to the following directive(s): soloTAN...
- Page 32 Fuji Spray Sunless ™ CONNECT WITH US! @fujispraysunless @fujispraysunless @fujispraysunless NEED HELP? fujispray.com fujispraysunless.com support@fujispray.com +1-800-650 0930 Fuji Industrial Spray Equipment Ltd. 800 Alness Street, Toronto, ON, Canada M3J 2H5...
Need help?
Do you have a question about the SUNLESS salonTAN Series and is the answer not in the manual?
Questions and answers