Page 2
This document is copyrighted by DJI with all rights reserved. Unless otherwise authorized by DJI, you are not eligible to use or allow others to use the document or any part of the document by reproducing, transferring or selling the document. Only refer to this document and the content thereof as instructions to operate DJI products.
Page 4
DJI Goggles N3 User Manual • The interface and functions of DJI Fly may vary as the software version is updated. Actual user experience is based on the software version used. Download DJI Assistant 2 ™ Download DJI ASSISTANT 2 (Consumer Drones Series) at: https://www.dji.com/downloads/softwares/dji-assistant-2-consumer-drones-series...
Page 5
DJI Goggles N3 User Manual Contents Using the Manual Legend Read Before Use Video Tutorials Download the DJI Fly App Download DJI Assistant 2 Overview Preparing the Goggles Powering on the Goggles Wearing the Goggles Activation Linking Linking via DJI Fly App (recommended)
Page 7
DJI Goggles N3 User Manual Overview 1. Power Button 7. Headband 2. Back Button 8. Battery Compartment 3. 5D Button 9. Headband Adjustment Knob 4. USB-C Port 10. Foam Padding 5. microSD Card Slot 11. Lens 6. Antennas 12. Power Cable •...
Page 8
DJI Goggles N3 User Manual Preparing the Goggles 2.1 Powering on the Goggles Press the power button once to check the current battery level. Press once, then press and hold for two seconds to power the goggles on or off.
Page 9
DJI Goggles N3 User Manual 2.2 Wearing the Goggles • Fold the antennas to avoid damage when the goggles are not in use. • DO NOT tear or scratch the foam padding, and the soft side of the battery compartment, or other components with sharp objects.
Page 11
The goggles must be activated and updated before using for the first time. Connect the USB-C port of the goggles to the smartphone. Run DJI Fly app and follow the on-screen instructions to activate the device and update the firmware. Make sure the smartphone is connected to the internet during activation.
Page 12
4.1 Linking via DJI Fly App (recommended) Keep the goggles connected to the smartphone after activation. Tap Connection Guide on DJI Fly from the smartphone and follow the on-screen instructions for linking. 4.2 Linking via Button 1. Linking the aircraft and the goggles: a.
Page 13
DJI Goggles N3 User Manual c. Once linking is completed, the battery level LEDs of the aircraft turn solid and display the battery level, the goggles stop beeping, and image transmission can be displayed normally. 2. Linking the goggles and remote control device: a.
Page 14
DJI Goggles N3 User Manual Using the Goggles • Using the goggles does not satisfy the requirement of visual line of sight (VLOS). Some countries or regions require a visual observer to assist during flight. Make sure to comply with local regulations when using the goggles. Fly the aircraft in environments with good lighting and visibility.
Page 15
DJI Goggles N3 User Manual Press to return to the previous menu or exit the current view. 2. 5D Button Press or push to open different menus from the FPV view of the goggles. After the menu is opened, push to navigate through the menu or adjust the parameter value.
Page 16
DJI Goggles N3 User Manual Goggles Menu Press down the 5D button or push it to the right from the FPV view to open the menu. • Enter Settings > Safety, Camera View Before Loss helps to find the location of the aircraft by using the captured video of the aircraft within a period before the signal is lost.
Page 17
Push the button backward to enter playback settings and adjust the screen brightness or volume. 5.3 AR Cursor • AR Cursor is only supported when used with DJI RC Motion 3 (hereinafter referred to as motion controller). • AR Cursor cannot function properly when being used on moving objects, such as cars and ships.
Page 18
DJI Goggles N3 User Manual If the cursor still cannot be found, tilt the motion controller up or down until the cursor appears on the screen. Operating the Menu • Using motion controller movements, move the cursor to the arrow on the left side of the screen.
Page 19
DJI Goggles N3 User Manual • Move the cursor to the arrow on the top of the screen, press the accelerator to enter the shortcut menu, and configure settings such as recording. • Move the cursor to the arrow on the bottom of the screen, press the accelerator to enter camera settings, and configure settings for the parameters of the aircraft camera.
Page 20
DJI Goggles N3 User Manual Controlling Video Playback When playing videos stored on the microSD card of the goggles, the cursor can be used to control playback such as: • Press the accelerator to pause or continue to play, push the accelerator forward to exit.
Page 22
DJI Goggles N3 User Manual Broadcasting to Other Goggles 1. Enter the DJI Goggles N3 menu, select Transmission and enter the Pilot sub-menu. 2. Turn on Broadcasting mode, and the device number will be displayed. 3. On the other goggles, enter the goggles menu, select Transmission and enter the Audience sub-menu.
Page 23
DJI Goggles N3 User Manual Maintenance 6.1 Replacing the Foam Padding 1. Hold the position as shown below and remove the foam padding gently. 2. Align the positioning columns of the new foam padding with the positioning holes on the goggles. Install it and press along the contour. After hearing a clicking sound, check and make sure that there is no gap between the foam padding and the goggles.
Page 24
DJI Goggles N3 User Manual • DO NOT use alcohol or other cleanser to wipe the foam padding and the soft side of the battery compartment. • DO NOT tear or scratch the foam padding, and the soft side of the battery compartment, or other components with sharp objects.
Page 25
Use one of the following methods to update the firmware: Using DJI Fly App When used with DJI Neo or DJI Avata 2, the aircraft, goggles, and remote control device can be updated together. Power on the aircraft, goggles, and remote control device. Make sure all the devices are linked.
Page 26
DJI support. 7.5 Troubleshooting 1. Power-on and start-up problems Check if the battery has power. Contact DJI support if it cannot be started normally. 2. Power-off and shutdown problems Contact DJI support. 3. The device is not functioning after powering on.
Page 27
4. SW update issues Follow the instructions in the user manual to update the firmware. If the firmware update fails, restart all the devices and try again. If the problem persists, contact DJI support. 5. Procedures to reset to factory default or last known working configuration Open the goggles menu and select Settings >...
Need help?
Do you have a question about the GOGGLES N3 and is the answer not in the manual?
Questions and answers