Kenwood Rapid Bake BM450 Manual

key

1. lid handle
2. viewing window
3. automatic dispenser
4. heating element
5. bread pan handle
6. kneader
7. drive shaft
8. drive coupling
9. on/off switch
10. measuring cup
11. dual measuring spoon 1tsp & 1tbsp
12. control panel
13. display window
14. program status indicator
15. crust colour indicators (light, medium, dark)
16. delay timer buttons
17. menu button
18. loaf size button
19. program button
20. confirm button
21. viewing light
22. favourite button
23. start/stop button
24. rapid bake button
25. cancel button
26. crust colour button
27. loaf size indicators

how to measure ingredients

(refer to illustrations 3 to 7)
It is extremely important to use the exact measure of ingredients for best results.

• Always measure liquid ingredients in the see-through measuring cup with graduated markings provided. Liquid should just reach marking on cup at eye level, not above or below (see 3).
• Always use liquids at room temperature, 20ºC/68ºF, unless making bread using the rapid 1 hour cycle.
  Follow the instructions given in the recipe section.
• Always use the measuring spoon provided to measure smaller quantities of dry and liquid ingredients. Use the slider to select between the following measure - ¹⁄2 tsp, 1 tsp, ¹⁄2 tbsp or 1 tbsp. Fill to the top and level off the spoon (see 6).

on/off switch

Your Kenwood breadmaker is fitted with an ON/OFF switch and will not operate until the "on" switch is pressed.

• Plug in and press the ON/OFF switch situated at the back of the breadmaker - the unit will beep and 1 (3:15) will appear in the display window.
• Always switch off and unplug your breadmaker after use.

program status indicator

The program status indicator is situated in the display window and the indicator arrow will point to the stage of the cycle the breadmaker has reached as follows: -
Pre-heat – The pre-heat feature only operates at the start of the wholewheat (30 minutes), wholewheat rapid (5 minutes) and gluten free (8 minutes) settings to warm the ingredients before the first kneading stage begins.
There is no kneader action during this period.
Knead – The dough is either in the first or 2nd kneading stage or being knocked back between the rising cycles. During the last 20 minutes of the 2nd Kneading cycle on setting (1), (2), (3). (4). (5). (6). (9), (10), (11) and (13) the automatic dispenser will operate and an alert will sound to tell you to add any additional ingredients manually.
Rise – the dough is in either the 1st, 2nd or 3rd rising cycle.
Bake – The loaf is in the final baking cycle.
Keep Warm – The bread maker automatically goes into the Keep warm mode at the end of the baking cycle. It will stay on the keep warm mode for up to 1hour or until the machine is turned off, which ever is soonest. Please note: the heating element will switch on and off and will glow intermittently during the keep warm cycle.

using your product

1. Remove the bread pan by holding the handle and turning the pan to the back of the baking chamber.
   
2. Fit the kneader.
   
3. Pour the water into the bread pan.
   
4. Add the rest of the ingredients to the pan in the order listed in the recipes. (see ill. 4-6)
   

7. Ensure that all the ingredients are weighed accurately as incorrect measures will produce poor results.
   
8. Insert the bread pan into the oven chamber by positioning the bread pan at an angle towards the back of the unit. Then lock the pan by turning it towards the front.
   
9. Lower the handle and close the lid.
   
10. Plug in and switch on - the unit will beep and default to setting 1 (3:15).
    
11. Press the MENU button until the required program is selected. The breadmaker will default to 1Kg & medium crust colour. Note: If using the "RAPID BAKE" , just press the button and the program will start automatically.
    
12. Select the loaf size by pressing the LOAF SIZE button until the indicator moves to the required loaf size.
    
13. Select the crust colour by pressing the CRUST button until the indicator moves to the required crust colour (light, medium or dark).
    
14. Press the START/STOP button . To stop or cancel the program press the START/STOP button for 2 -3 seconds.
    
15. At the end of the baking cycle unplug the breadmaker.
    
16. Remove the bread pan by holding the handle and turning the pan to the back of the baking chamber.
    Always use oven gloves as the pan handle will be hot and take care not to touch the automatic dispenser on the underside of the lid as this will also be hot.
    
17. Then turn out onto a wire rack to cool.
    
18. Leave the bread to cool for at least 30 minutes before slicing, to allow the steam to escape. The bread will be difficult to slice if hot.
    
19. Clean the bread pan and kneader immediately after use (see care and cleaning).
    

viewing light

• The LIGHT button can be pressed at any time to view the program status in the display window or to check the progress of the dough inside the baking chamber.
• The baking chamber viewing light will automatically switch off after 60 seconds..
• If the light bulb stops working it must be replaced by KENWOOD or an authorised KENWOOD repairer (see service and customer care).

automatic dispenser

Your BM450 breadmaker is fitted with an automatic dispenser for releasing additional ingredients directly into the dough during the kneading cycle. This ensures that the ingredients are not overprocessed or crushed and are evenly distributed.

to fit and use the automatic dispenser

1. Fit the dispenser to the lid using the alignment arrows .
   • The dispenser will not locate and lock into position unless fitted the correct way round.
   • The breadmaker can be used without the dispenser fitted if required but the manual alert will still sound.
2. Fill the dispenser with the required ingredients.
3. The Automatic dispenser operates after approx. 15-20 minutes of kneading and an audible alert sounds as well in case you need to add ingredients manually.

hints & tips
Not all ingredients are suitable for use with the automatic dispenser and for best results follow the guidelines below: -

• Do not overfill the dispenser – follow the recommended quantities specified in the recipes supplied.
• Keep the dispenser clean and dry to prevent ingredients sticking.
• Cut ingredients roughly or lightly dust with flour to reduce stickiness, which may prevent the ingredients from being released.

automatic dispenser usage chart

bread/dough program chart

*An alert will sound before the end of the 2nd kneading cycle to add ingredients if the recipe recommends doing so.
*The Bread maker will automaticaly go in to the keep warm mode at the end of the baking cycle. It will stay in the keep warm mode for up to 1 hour or until the machine is turned off, which ever is soonest.

delay timer

The Delay timer allows you to delay the bread making process up to 15 hours. The delayed start cannot be used with the "RAPID BAKE" program or programs (7) to (13).

When using this delayed start function you must not use perishable ingredients – things that 'go off' easily at room temperature or above, such as milk, egg, cheese and yoghurt etc.

To use the DELAY TIMER simply place the ingredients in the bread pan and lock the pan into the bread maker. Then:

• Press the MENU button to choose the required program – the program cycle time is displayed.
• Select the crust colour and size required.
• Then set the delay timer.
• Press the (+) TIMER button and keep pressing until the total time required is displayed. If you go past the required time press the (-) TIMER button to go back. The timer button when pressed, moves in 10 minute increments. You do not need to work out the difference between the program time selected and the total hours required as the bread maker will automatically include the setting cycle time.
  Example: Finished loaf required at 7am. If the breadmaker is set up with the required recipe ingredients at 10pm the evening before, total time to be set on the delayed timer is 9 hours.
• Press the MENU button to choose your program e.g. 1 and use the (+) TIMER button to scroll the time in 10 minute increments to display '9:00'. If you go past '9:00', simply press the (-) TIMER button until you return to '9:00'.
  
• Press the START/STOP button and the display colon (:) will flash. The timer will start to count down.
  
• If you make a mistake or wish to change the time set, press the START/STOP button until the screen clears. You can then reset the time.
  

favourite program

The Favourite program allows you to create and store up to 5 of your own programs.

to Create/Modify Own Program

1. Plug in and switch on.
2. Press the FAVOURITE button to select the program you wish to change from P1 to P5.
3. Press the (P) PROGRAM button to start modifying the program.
4. Use the DELAY TIMER buttons (-) & (+) to change the time required for each stage.
5. Press the CONFIRM button to save the change and move to the next stage of the program.
6. Repeat stage 3 to 5 until all stages have been programmed as required. The program status indicator shows what stage of the program you have reached.
7. When the CONFIRM button is pressed for the last time after the keep warm stage a beep will sound and the program will be automatically saved.
8. If you want to move back to the previous stage press the CANCEL button to change the time.

to use the favourite program

1. Plug in and switch on.
2. Press the FAVOURITE button to choose the required program P1 to P5.
3. Press the START/STOP button or select the delay timer function.

P1 – P5 Favourite Pad Program Stages
Stage		Default Setting	Min and Max Time Change Available
1	Pre-Heat	0mins	0 – 60mins
2	Knead 1	3mins	0 – 10mins
3	Knead 2	22mins	0 – 30mins
4	Rise 1	20mins	20 – 60mins
5	Knead 3	15secs	Non changeable Kneader will not operate if Rise 2 set to 0
6	Rise 2	30mins	0 – 2hrs
7	Knead 4	15secs	Non changeable Kneader will not operate if Rise 3 set to 0
8	Rise 3	50mins	0 – 2hrs
9	Baking	60mins	0 – 1hr 30mins
10	Keep Warm	60mins	0 – 60mins

power interruption protection

Your Bread Maker has an 8 minute power interruption protection in case the unit is accidentally unplugged during operation. The unit will continue the program if plugged back in straight away.

care and cleaning

• Unplug the bread maker and allow to cool completely before cleaning.
• Do not immerse either the bread maker body or the outside base of the bread pan in water.
• Do not use abrasive scouring pads or metal implements.
• Use a soft damp cloth to clean the outside and inside surfaces of the bread maker if necessary.

bread pan

• Do not dishwash the bread pan.
• Clean the bread pan and the kneader immediately after each use by partially filling the pan with warm soapy water. Leave to soak for 5 to 10 minutes. To remove the kneader, turn clockwise and lift off. Finish cleaning with a soft cloth, rinse and dry.
  If the kneader cannot be removed after 10 minutes, hold the shaft from underneath the pan and twist back and forth until the kneader is released.

glass lid

• Lift off the glass lid and clean with warm soapy water.
• Do not dishwash the lid.
• Ensure the lid is completely dry before refitting to the bread maker.

automatic dispenser

• Remove the automatic dispenser from the lid and wash in warm soapy water and if required use a soft brush to clean. Ensure the dispenser is completely dry before refitting to the lid.

Recipes

(add the ingredients to the pan in the order listed in the recipes)

Basic White Bread

Program 1

tsp = 5 ml teaspoon
tbsp = 15ml tablespoon

Brioche Bread

(use light crust colour)
Program 6

Wholemeal Bread

Program 3

1 Put the egg/eggs into the measuring cup and add sufficient water to give: -

2 Pour into the bread pan with the honey and lemon juice.

Rapid White Bread

Rapid Bake Button

1 Press the RAPID BAKE button and the program will start automatically.

Bread rolls

Program 10

1 At the end of the cycle, turn the dough out onto a lightly floured surface. Gently knock back the dough and divide into 12 equal pieces and hand shape.
2 After shaping, leave the dough for a final proving then bake in your conventional oven.

ingredients

The major ingredient in bread making is flour, so selecting the right one is the key to a successful loaf.

wheat flours
Wheat flours make the best loaves. Wheat consists of an outer husk, often referred to as bran, and an inner kernel, which contains the wheat germ and endosperm. It is the protein within the endosperm which, when mixed with water, forms gluten. Gluten stretches like elastic and the gases given off by the yeast during fermentation are trapped, making the dough rise.

white flours
These flours have the outer bran and wheat germ removed, leaving the endosperm which is milled into a white flour. It is essential to use strong white flour or white bread flour, because this has a higher protein level, necessary for gluten development. Do not use plain white flour or self-raising flour for making yeast risen breads in your bread maker, as inferior loaves will be produced. There are several brands of white bread flour available, use a good quality one, preferably unbleached, for the best results.

wholemeal flours
Wholemeal flours include the bran and wheat germ, which gives the flour a nutty flavour and produces a coarser textured bread. Again strong wholemeal or wholemeal bread flour must be used. Loaves made with 100% wholemeal flour will be more dense than white loaves. The bran present in the flour inhibits the release of gluten, so wholemeal doughs rise more slowly. Use the special wholewheat programs to allow time for the bread to rise. For a lighter loaf, replace part of the wholemeal flour with white bread flour. You can make a quick wholemeal loaf using the rapid whole wheat setting.

strong brown flour
This can be used in combination with white flour, or on its own. It contains about 80-90% of the wheat kernel and so it produces a lighter loaf, which is still full of flavour. Try using this flour on the basic white cycle, replacing 50% of the strong white flour with strong brown flour. You may need to add a little extra liquid.

granary bread flour
A combination of white, wholemeal and rye flours mixed with malted whole wheat grains, which adds both texture and flavour. Use on its own or in combination with strong white flour.

non-wheat flours
Other flours such as rye can be used with white and wholemeal bread flours to make traditional breads like pumpernickel or rye bread. Adding even a small amount adds a distinctive tang. Do not use on its own, as it will produce a sticky dough, which will produce a dense heavy loaf. Other grains such as millet, barley, buckwheat, cornmeal and oatmeal are low in protein and therefore do not develop sufficient gluten to produce a traditional loaf.
These flours can be used successfully in small quantities. Try replacing 10-20% of white bread flour with any of these alternatives.

salt
A small quantity of salt is essential in bread making for dough development and flavour. Use fine table salt or sea salt, not coarsely ground salt which is best kept for sprinkling on top of hand-shaped rolls, to give a crunchy texture. Low-salt substitutes are best avoided as most do not contain sodium.

• Salt strengthens the gluten structure and makes the dough more elastic.
• Salt inhibits yeast growth to prevent over-rising and stops the dough collapsing.
• Too much salt will prevent the dough rising sufficiently.

sweeteners
Use white or brown sugars, honey, malt extract, golden syrup, maple syrup, molasses or treacle.

• Sugar and liquid sweeteners contribute to the colour of bread, helping to add a golden finish to the crust.
• Sugar attracts moisture, so improving the keeping qualities.
• Sugar provides food for the yeast, although not essential, as modern types of dried yeast are able to feed on the natural sugars and starches found in the flour, it will make the dough more active.
• Sweet breads have a moderate level of sugar with the fruit, glaze or icing adding extra sweetness. Use the sweet bread cycle for these breads.
• If substituting a liquid sweetener for sugar then the total liquid content of the recipe will need to be reduced slightly.

fats and oils
A small amount of fat or oil is often added to bread to give a softer crumb. It also helps to extend the freshness of the loaf. Use butter, margarine or even lard in small quantities up to 25 g (1 oz) or 22ml (11⁄2 tbsp.) vegetable oil. Where a recipe uses larger amounts so the flavour is more noticeable, butter will provide the best result.

• Olive oil or sunflower oil can be used instead of butter, adjust the liquid content for amounts over 15ml (3 tsp) accordingly. Sunflower oil is a good alternative if you are concerned about the cholesterol level.
• Do not use low fat spreads as they contain up to 40% water so do not have the same properties as butter.

liquid
Some form of liquid is essential; usually water or milk is used. Water produces a crisper crust than milk. Water is often combined with skimmed milk powder. This is essential if using the time delay as fresh milk will deteriorate. For most programs water straight from the tap is fine, however on the rapid one-hour cycle it needs to be lukewarm.

• On very cold days measure the water and leave to stand at room temperature for 30 minutes before use. If using milk straight from the fridge do likewise.
• Buttermilk, yoghurt, soured cream and soft cheeses such as ricotta, cottage and fromage frais can all be used as part of the liquid content to produce a more moist, tender crumb. Buttermilk adds a pleasant, slightly sour note, not unlike that found in country style breads and sour doughs.
• Eggs may be added to enrich the dough, improve the colour of the bread and help to add structure and stability to the gluten during rising. If using eggs reduce the liquid content accordingly. Place the egg in a measuring cup and top up with liquid to the correct level for the recipe.

yeast
Yeast is available both fresh and dried. All the recipes in this book have been tested using easy blend, fast action dried yeast which does not require dissolving in water first. It is placed in a well in the flour where it is kept dry and separate from the liquid until mixing commences.

• For best results use dried yeast. The use of fresh yeast is not recommended as tends to give more variable results than dried yeast. Do not use fresh yeast with the delay timer.
  If you wish to use fresh yeast note the following: 6g fresh yeast = 1tsp dried yeast
  Mix the fresh yeast with 1tsp sugar and 2tbsp of the water (warm). Leave for 5 minutes until frothy.
  Then add to the rest of the ingredients in the pan.
  To get the best results the yeast quantity may need to be adjusted.
• Use the amounts stated in the recipes; too much could cause the bread to over-rise and spill over the top of the bread pan.
• Once a sachet of yeast is opened, it should be used within 48 hours, unless stated otherwise by the manufacturer. Re-seal after use. Resealed opened sachets can be stored in the freezer until required.
• Use dried yeast before its use by date, as the potency gradually deteriorates with time.
• You may find dried yeast, which has been manufactured especially for use in bread machines. This will also produce good results, though you may need to adjust the quantities recommended.

adapting your own recipes

After you have baked some of the recipes, supplied you may wish to adapt a few of your own favourites, which previously have been mixed and kneaded by hand. Start by selecting one of the recipes in this booklet, which is similar to your recipe, and use it as a guide.

Read through the following guidelines to help you, and be prepared to make adjustments as you go along.

• Make sure you use the correct quantities for the bread maker. Do not exceed the recommended maximum. If necessary, reduce the recipe to match the flour and liquid quantities in the breadmaker recipes.
• Always add the liquid to the bread pan first. Separate the yeast from the liquid by adding after the flour.
• Replace fresh yeast with easy blend dried yeast. Note: 6g fresh yeast = 1tsp (5ml) dried yeast.
• Use skimmed milk powder and water instead of fresh milk, if using the timer delay setting.
• If your conventional recipe uses egg, add the egg as part of the total liquid measurement.
• Keep the yeast separate from the other ingredients in the pan until mixing commences.
• Check the consistency of the dough during the first few minutes of mixing. Bread machines require a slightly softer dough, so you may need to add extra liquid. The dough should be wet enough to gradually relax back.

removing/slicing and storing bread

• For best results, once your loaf is baked, remove it from the machine and turn out of the bread pan immediately, although your bread maker will keep it warm for up to 1 hour if you are not around.
• Remove the bread pan from the machine using oven gloves, even if it is during the keep warm cycle. Turn the pan upside-down and shake several times to release the cooked bread. If the bread is difficult to remove, try gently knocking the corner of the bread pan on a wooden board, or rotate the base of the shaft underneath the bread pan.
• The kneader should remain inside the bread pan when the bread is released, however occasionally it may remain inside the loaf of bread. If so, remove it before slicing the bread, using a heat resistant plastic utensil to prise it out. Do not use a metal implement as this may scratch the non-stick coating on the kneader.
• Leave the bread to cool for at least 30 minutes on a wire rack, to allow the steam to escape. The bread will be difficult to slice if cut hot.

storing
Home-made bread does not contain any preservatives so should be eaten within 2-3 days of baking. If not eating immediately, wrap in foil or place in a plastic bag and seal.

• Crispy French-style bread will soften on storage, so is best left uncovered until sliced.
• If you wish to keep your bread for a few days, store in the freezer. Slice the bread before freezing, for easy removal of the amount required.

general hints and tips

The results of your bread making are dependent on a number of different factors, such as the quality of ingredients, careful measuring, temperature and humidity.
To help ensure successful results, there are a few hints and tips worth noting.
The bread machine is not a sealed unit and will be affected by temperature. If it is a very hot day or the machine is used in a hot kitchen, then the bread is likely to rise more, than if it is cold. The optimum room temperature is between 20°C /68°F and 24°C/75°F.

• On very cold days let the water from the tap stand at room temperature for 30 minutes before use. Likewise with ingredients from the fridge.
• Use all ingredients at room temperature unless stated otherwise in the recipe eg. for the rapid 1 hour cycle you will need to warm the liquid.
• Add ingredients to the bread pan in the order suggested in the recipe. Keep the yeast dry and separate from any other liquids added to the pan, until mixing commences.
• Accurate measuring is probably the most crucial factor for a successful loaf. Most problems are due to inaccurate measuring or omitting an ingredient. Follow either metric or imperial measurements; they are not interchangeable. Use the measuring cup and spoon provided.
• Always use fresh ingredients, within their use by date. Perishable ingredients such as milk, cheese, vegetables and fresh fruits may deteriorate, especially in warm conditions. These should only be used in breads, which are made immediately.
• Do not add too much fat as it forms a barrier between the yeast and flour, slowing down the action of the yeast, which could result in a heavy compact loaf.
• Cut butter and other fats into small pieces before adding to the bread pan.
• Replace part of the water with fruit juices such as orange, apple or pineapple when making fruit flavoured breads.
• Vegetable cooking juices can be added as part of the liquid. Water from cooking potatoes contains starch, which is an additional source of food for the yeast, and helps to produce a well-risen, softer, longer lasting loaf.
• Vegetables such as grated carrot, courgette or cooked mashed potato can be added for flavour. You will need to reduce the liquid content of the recipe as these foods contain water. Start with less water and check the dough as it begins to mix and adjust if it is necessary.
• Do not exceed the quantities given in recipes as you may damage your bread machine.
• If the bread does not rise well try replacing the tap water with bottled water or boiled and cooled water. If your tap water is heavily chlorinated and fluorinated it may affect the bread rising. Hard water can also have this effect.
• It is worth checking the dough after about 5 minutes of continuous kneading. Keep a flexible rubber spatula next to the machine, so you can scrape down the sides of the pan if some of the ingredients stick to the corners. Do not place near the kneader, or impede its movement. Also check the dough to see if it is the correct consistency. If the dough is crumbly or the machine seems to be labouring, add a little extra water. If the dough is sticking to the sides of the pan and doesn't form a ball, add a little extra flour.
• Do not open the lid during the proving or baking cycle as this may cause the bread to collapse.

troubleshooting guide

Following are some typical problems that can occur when making bread in your bread maker. Please review the problems, their possible cause and the corrective action that should be taken to ensure successful bread making.

safety

• Read these instructions carefully and retain for future reference.
• Remove all packaging and any labels.
• Do not touch hot surfaces. Accessible surfaces are liable to get hot during use. Always use oven gloves to remove the hot bread pan.
• To prevent spillages inside the oven chamber, always remove the bread pan from the machine before adding the ingredients. Ingredients that splash onto the heating element can burn and cause smoke.
• Do not use this appliance if there is any visible sign of damage to the supply cord or if it has been accidentally dropped.
• Do not immerse this appliance, the supply cord or the plug in water or any other liquid.
• Always unplug this appliance after use, before fitting or removing parts or before cleaning.
• Do not let the electrical supply cord hang over the edge of a work surface or allow it to touch hot surfaces such as a gas or electric hob.
• This appliance should only be used on a flat heat resistant surface.
• Do not place your hand inside the oven chamber after the bread pan has been removed as it will be very hot.
• Do not touch moving parts within the Bread Maker.
• Do not exceed the maximum flour and raising agent quantities specified in the recipes supplied.
• Do not place the Bread Maker in direct sun light, near hot appliances or in a draught. All these things can affect the internal temperature of the oven, which could spoil the results.
• Do not use this appliance outdoors.
• Do not operate the Bread Maker when it is empty as this could cause it serious damage.
• Do not use the oven chamber for any type of storage.
• Do not cover the vents on the side of the machine and ensure there is adequate ventilation around the bread maker during operation.
• This appliance is not intended to be operated by means of an external timer or separate remote-control system.
• Do not immerse either the bread maker body or the outside base of the bread pan in water.
• Children from 8 years and above can use, clean and perform user maintenance on this appliance in accordance with the User Instructions provided they are supervised by a person responsible for their safety and have been given instruction concerning the use of the appliance and are aware of the hazards.
• Persons with reduced physical, sensory or mental capabilities or lack of knowledge using this appliance must have been given supervision or instruction on its safe use and are aware of the hazards.
• Children must not play with the appliance and both appliance and cord must be out of reach of children less than 8 years.
• Unplug the bread maker and allow to cool completely before cleaning.
• Only use the appliance for its intended domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions.

before plugging in

• Make sure your electricity supply is the same as the one shown on the underside of your Bread Maker.
• 
  UK only – The wires in the cord are coloured as follows:
  Green & Yellow = Earth
  Blue = Neutral
  Brown = Live
• The appliance must be protected by a 13A approved (BS1362) fuse.
• 
  THIS APPLIANCE MUST BE EARTHED.
• Note:
  For non-rewireable plugs the fuse cover MUST be refitted when replacing the fuse. If the fuse cover is lost then the plug must not be used until a replacement can be obtained. The correct fuse cover is identified by colour and a replacement may be obtained from your Kenwood Authorised Repairer (see Service).
• 
  If a non-rewireable plug is cut off it must be DESTROYED IMMEDIATELY. An electric shock hazard may arise if an unwanted non-rewireable plug is inadvertently inserted into a 13A socket outlet.
• This appliance conforms to EC directive 2004/108/EC on Electromagnetic Compatibility and EC regulation no. 1935/2004 of 27/10/2004 on materials intended for contact with food.

before using your appliance for the first time

• Wash all parts (see care and cleaning).
• Fit the lid (see care & cleaning).
• Fit the automatic dispenser to the underside of the lid (see automatic dispenser).

service and customer care

• If the cord is damaged it must, for safety reasons, be replaced by KENWOOD or an authorised KENWOOD repairer.

If you need help with:

• using your machine or
• servicing or repairs (in or out of guarantee)
  call Kenwood customer care on 023 9239 2333.
  Have your model number ready (BM450) and date code (5 digit code ie 13L35) ready - they are located on the base of your Bread Maker.
• spares and attachments
  call 0844 557 3653.
• other countries
• Contact the shop where you bought your Bread Maker.
• Designed and engineered by Kenwood in the UK.
• Made in China.

HEAD OFFICE: Kenwood Limited, 1-3 Kenwood Business Park, New Lane, Havant, Hampshire PO9 2NH
kenwoodworld.com

Documents / Resources

References

• Kenwood NL | Innovatieve keukenapparatuur

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Kenwood Rapid Bake BM450 Manual