Page 3 Trademarks and registered trademarks Autohelm, HSB, RayTech Navigator, Sail Pilot, SeaTalk and Sportpilot are UK registered trademarks of Raymarine UK Limited. Pathfinder and Raymarine are UK registered trademarks of Raymarine Holdings Limited. 33STV, 45STV, 60STV, AST, Autoadapt, Auto GST, AutoSeastate, AutoTrim, Bidata, G Series, HDFI, LifeTag, Marine Intelligence, Maxiview, On Board, Raychart, Raynav, Raypilot, RayTalk, Raystar, ST40, ST60+, Seaclutter, Smart Route, Tridata, UniControl, Hybridtouch, and Waypoint Navigation are trademarks of Raymarine UK Limited.
Page 5: Table Of Contents
Contents Chapter 1 Important information....... 9 3.5 Touchscreen overview ..........24 3.6 Home screen overview ..........24 Safety notices..............9 3.7 Pages ..............25 TFT LCD Displays ............10 3.8 Applications .............. 27 Water ingress ..............10 3.9 Screen overview ............29 Disclaimers ..............
Page 6 6.3 Chart views............... 75 9.2 HD and SuperHD digital radar scan speed....116 6.4 Chart planning options..........78 9.3 Radar scanner status symbols ......... 117 6.5 Chart navigation options ..........78 9.4 Radar range and image quality ........ 118 6.6 Measuring distances and bearings ......79 9.5 Radar display overview ...........
Page 7 10.11 AIS alarms ............156 13.6 Changing what the engine application displays ............192 10.12 Buddy tracking ............ 156 Chapter 14 Using the data application ....193 Chapter 11 Using the Course Deviation Indicator ............ 159 14.1 Data application overview ........194 14.2 Pre-configured data panels ........
Page 8 21.6 Resetting your display ........... 242 16.6 Sirius radio parental locking ........216 Chapter 22 Technical support ....... 245 Chapter 17 Using Navtex ........217 22.1 Raymarine technical support ........246 17.1 Navtex overview............ 218 22.2 3rd party support ........... 247 17.2 Navtex setup............218 17.3 Viewing and managing Navtex messages ....
Page 9: Chapter 1 Important Information
• SWITCH OFF the sounder if divers are likely to be notices to mariners, caution and proper navigational within 25 ft (5 m) of the transducer. skill when operating this or any other Raymarine product. Warning: Radar scanner safety Warning: Product installation and...
Page 10: Tft Lcd Displays
It is the user’s responsibility to use official government charts, notices to mariners, caution and proper navigational skill • Do NOT use abrasive, or acid or ammonia based when operating this or any other Raymarine product. This product products. supports electronic charts provided by third party data suppliers •...
Page 11: Compactflash Cards
(as applicable). Raymarine equipment and accessories conform to the appropriate Raymarine does not warrant that this product is error-free or that it Electromagnetic Compatibility (EMC) regulations for use in the is compatible with products manufactured by any person or entity recreational marine environment.
Page 12: Product Disposal
Directive requires the recycling of waste electrical and electronic equipment. Whilst the WEEE Directive does not apply to some Raymarine products, we support its policy and ask you to be aware of how to dispose of this product. Warranty registration...
Page 13: Chapter 2 Handbook Information
Chapter 2: Handbook information Chapter contents • 2.1 Handbook information on page 14 • 2.2 Handbook conventions on page 15 Handbook information...
Page 14: Handbook Information
Part number E-Series Widescreen range of multifunction displays. Installation and commissioning 87116 The handbook is for use with the following models: instructions • E90W Widescreen Multifunction Display Operating instructions (quick 86137 reference) • E120W Widescreen Multifunction Display User reference handbook 81320 •...
Page 15: Handbook Conventions
2.2 Handbook conventions Conventions used in this handbook. The following conventions are used throughout this handbook when referring to: • Softkeys — the term "select" is used in procedures involving softkeys to refer to the action of selecting a softkey, either using touch or by pressing the corresponding physical key.
Page 16 E-Series Widescreen User reference...
Page 17: Chapter 3 Getting Started
Chapter 3: Getting started Chapter contents • 3.1 Multifunction display system integration on page 18 • 3.2 Display power on page 20 • 3.3 Controls on page 21 • 3.4 Hybridtouch overview on page 23 • 3.5 Touchscreen overview on page 24 •...
Page 18: Multifunction Display System Integration
3.1 Multifunction display system following table details which devices may be connected to your display, and the type of connectivity (in terms of protocols and integration physical interfaces) that they use to exchange data with the display: You can connect a number of external devices to your multifunction display, providing additional features and functions.
Page 19 • Navionics Fish’N Chip • 4 kilowatt HD Digital • Navionics Hotmaps Open Array Scanner. Refer to the • 4 kilowatt SuperHD Raymarine website Digital Open Array (www.raymarine.com) Scanner. for the latest list of supported chart cards. • 12 kilowatt SuperHD...
Page 20: Display Power
SeaTalk, SeaTalk , or Powering the display on third-party external GPS NMEA 0183 receiver 1. Press and hold the POWER button until the Raymarine logo appears. Instruments All current Raymarine SeaTalk, SeaTalk , or 2. Press OK to acknowledge the warning window.
Page 21: Controls
3.3 Controls Screen item Description Chart card slot — open the card reader door to insert or remove CompactFlash (CF) cards. CF cards are used for additional cartography, archiving waypoint, route, and track data, and upgrading system software. Home — displays the home screen, where you can access all the application pages and your waypoint, track, and route data.
Page 22: Using The Cursor
Touch icons You can use the BACK and CLOSE icons to move between the different levels of softkeys available in each application. Back — go back one level (same effect as CANCEL button). 1. Rotary Control. Use this to select menu options and adjust the value of various items.
Page 23: Hybridtouch Overview
Course Over Ground Chart may also be situations (such as rough sea conditions) when it is not vector appropriate to use the touchscreen. In these situations, Raymarine Center of radar Radar strongly recommends that you enable the touch lock, and use the physical keys to operate your multifunction display.
Page 24: Touchscreen Overview
• Placing and moving the cursor. • Placing and moving VRMs and EBLs. Note: Raymarine strongly recommends that you familiarize yourself with touch operations while your vessel is anchored or moored. You may find it helpful to use the simulator mode (accessible from Menu >...
Page 25: Pages
3.7 Pages Screen item Description Touch Lock — select this icon to lock the touchscreen, Pages are used on your multifunction display to show applications. preventing accidental use. To unlock, use the UniControl Pages are displayed and accessed on the home screen. Each page to deselect the Touch Lock icon.
Page 26 You can also define a "layout" for each page, which determines how 5. Select the application(s) you want to display on the page. the applications are arranged on the screen. Adding a new page to the home screen Multiple applications With the home screen displayed: With most applications, it is possible to run 4 instances of the same 1.
Page 27: Applications
3.8 Applications Resetting the home screen to default settings With the home screen displayed: Chart application — provides a 2D or 3D graphical view of your charts to 1. Select the Customize icon. help you navigate. Waypoint, route, and 2. Select the RESET ALL PAGES TO DEFAULT softkey. track functions enable you to navigate 3.
Page 28 Engine application — enables you to Weather application — (North America view information in the form of gauges only). With a suitable weather receiver and digital data, from up to 3 compatible connected to your multifunction display, engines. the weather application overlays historical, live, and forecasted weather graphics on a world map.
Page 29: Screen Overview
3.9 Screen overview Screen item Description Edit dialogs — enable data to be edited or entered into a list — for example, editing a waypoint.. Pop-up messages — alert you to a situation (such as an alarm), or unavailable function. Pop-up messages may require a response from you —...
Page 30 Screen item Description Back — select this icon to go back to a previous menu. Menu item — momentarily touching a menu item highlights and automatically selects the item. You can also use the trackpad or rotary control to highlight an item, and the OK button to select it.
Page 31 Screen item Description Screen item Description Details — displays the details of the currently selected Back — select this icon to go back to a previous dialog. list item. Field — touching a text field automatically displays the Close — select this icon to close the dialog(s). on-screen keyboard, which can be used to edit the details.
Page 32: Editing Information In Dialogs
3.10 Editing information in dialogs With the dialog displayed: 1. Use the touchscreen or UniControl to select the field you want to edit. The on-screen keyboard is displayed: Screen item Description 2. Use the on-screen keyboard to make the changes. Back —...
Page 33: Basic Touchscreen Operations
3.11 Basic touchscreen operations Locking the touchscreen With the home screen displayed: Placing and moving the cursor using touch 1. Select the Touch Lock icon. 1. Touch the screen at any position on the screen to place the It changes color to indicate that the touchscreen is disabled. All cursor there.
Page 34: Status Symbols
3.12 Status symbols Radar power The status symbols on the databar confirm whether the appropriate Symbol mode Description connections to your multifunction display have been made. Transmit Rotating icon, signifying that the The symbols show the status for the following: (TX) scanner is on and transmitting.
Page 35: Autopilot Status Symbols
Symbol Description Symbol Description AIS unit is switched on and operating. Symbol animated: the DSM is connected and transmitting. AIS currently unavailable. Symbol static: the DSM is connected but not transmitting. AIS unit is switched off, or not connected. Symbol greyed-out: the DSM is not connected, or is not detected.
Page 36 Symbol Description Symbol Description Autopilot is in Standby mode. Power steering active. Autopilot is in Track mode. Wind Vane mode is active. Autopilot is in Auto mode. Touchscreen lock status symbols The touchscreen lock status is indicated in the databar. No autopilot detected.
Page 37: Initial Setup Procedures
Once your display has been installed and commissioned (see 4. Change the Safe Depth, Safe Heightand Safe Width settings Installation Guide), Raymarine recommends that you: as appropriate for your vessel. • Set the language, the date and time format and preferred units Note: The settings you specify for your vessel details are of measurement.
Page 38: Data Master
Data master Any system containing more than one networked multifunction display must have a designated data master. The data master is the display which serves as a primary source of data for all displays, it also handles all external sources of information.
Page 39: Simulator Mode
You can also adjust the vessel speed in simulator mode. This is useful for quickly moving to different areas of the chart, for example. Note: Raymarine recommends that you do NOT use the simulator mode whilst navigating. Note: The simulator will NOT display any real data, including any safety messages (such as those received from AIS units).
Page 40 E-Series Widescreen User reference...
Page 41: Chapter 4 Managing Display Data
Chapter 4: Managing display data Chapter contents • 4.1 CompactFlash cards overview on page 42 • 4.2 Writing and retrieving data on page 44 • 4.3 Transferring data using NMEA on page 45 Managing display data...
Page 42: Compactflash Cards Overview
4.1 CompactFlash cards overview Caution: Care of chart cards CompactFlash cards enable you to use additional cartographic To avoid irreparable damage to and/or loss of data from chart cards: information, and archive data. Their uses include: • Ensure that chart cards are fitted the correct way around.
Page 43 4. Press the card eject button. 5. To prevent the ingress of water and consequent damage, close the chart card door and press firmly until a click is heard. Caution: Ensure chart card door is securely closed To prevent water ingress and consequent damage to the display, ensure that the chart card door is firmly closed.
Page 44: Writing And Retrieving Data
Saving data to a CompactFlash card Erasing data from a CompactFlash card Note: Raymarine strongly recommends that you save data to a 1. Insert the card in to the CompactFlash card slot. separate CompactFlash card, and not to a chart card containing 2.
Page 45: Transferring Data Using Nmea
4.3 Transferring data using NMEA You can transfer waypoints or routes to and from your multifunction display and an external instrument, using NMEA. Transferring waypoint and route data using NMEA With NMEA-compatible equipment powered on and connected to your multifunction display: 1.
Page 46 E-Series Widescreen User reference...
Page 47: Chapter 5 Using Waypoints, Routes And Tracks
Chapter 5: Using waypoints, routes and tracks Chapter contents • 5.1 Waypoints on page 48 • 5.2 Routes on page 59 • 5.3 Tracks on page 65 • 5.4 Waypoints, routes and tracks storage capacity on page 67 Using waypoints, routes and tracks...
Page 48: Waypoints
5.1 Waypoints Item Description Inactive waypoint A waypoint is a position marked on the screen to indicate a site or a place to navigate to. Active waypoint As well as acting as position markers, waypoints are also the Alternative waypoint symbols building blocks used to create routes.
Page 49 Selecting a waypoint hotspot also provides the following the softkey functions: • Erase waypoint. • Move waypoint. • Go to waypoint. • View / edit waypoint. Waypoint features There are a range of features for placing, navigating and managing waypoints. Waypoints in the fishfinder application Waypoint features are accessed from: Waypoints in the fishfinder application are represented by a vertical...
Page 50 In the chart, radar, fishfinder, or CDI application: Waypoint function applications Home screen 1. Press the WPTS MOB button. Edit waypoint information 2. Touch the area of the screen where you want the waypoint. 3. (Optionally) select the waypoint Name, Group, or Symbol field to customize the waypoint details.
Page 51: Waypoint Navigation
2. Select the WAYPOINT AT LAT/LON softkey. Navigating to a waypoint on the screen 3. Select the EDIT USING KEYPAD softkey. 4. Enter the Latitude/Longitude position. 5. Select SAVE. 6. Close the window. Waypoint navigation Navigating to the cursor position on the chart In the chart or radar application: 1.
Page 52: Waypoint Information
Cancelling navigation to a waypoint • Use the waypoint list for comprehensive information to view and edit as required. 1. Press the WPTS/MOB button. 2. Select the GOTO WAYPOINT OPTIONS softkey. Displaying the waypoint list 3. Select the STOP GOTO softkey. 1.
Page 53 Waypoint symbols Symbol Type Symbol Type There are a range of symbols to represent different waypoint types. Lost target Man overboard (MOB) Symbol Type Symbol Type Marker Martini Airport Anchor NMEA Nuns Billfish Bottom mark Oil rig Oyster Bridge Buoy Post Preferred marks Cans...
Page 54: Moving Waypoints
4. Using the SHOW BY softkey, select the SHOW BY GROUP or Symbol Type Symbol Type SHOW BY SYM option, as appropriate. Trawler Tree A list of available waypoint groups or symbols is displayed. 5. Select the waypoint group or symbol that you want to show or Triangle Wreck hide.
Page 55: Waypoint Groups
Moving a waypoint by entering new coordinates 3. Select the ERASE FROM SYSTEM softkey. 4. Use the SELECT LIST softkey to select the WPT option. With the Waypoint List displayed: 5. Select the ERASE ALL WAYPOINTS softkey. 1. Select the VIEW AND EDIT DETAILS softkey. 6.
Page 56: Managing Waypoints
Making a new waypoint group The on-screen keyboard is displayed. 4. Using the on-screen keyboard, edit the group name. With the Waypoint Group List displayed: 5. Select the on-screen keyboard’s SAVE key. 1. Select the MAKE NEW GROUP softkey. Changing the default waypoint group 2.
Page 57 • Transfer your waypoints to other NMEA compatible equipment. 2. Select the ARCHIVE AND TRANSFER softkey. 3. Select the TRANSFER ON NMEA softkey. • Password protect your waypoints to prevent unauthorized access. 4. Select the appropriate port number, using the NMEA PORT softkey.
Page 58 10. Add a hint to help you remember the password (optional). 11. Press the OK button. Note: Raymarine strongly recommends that you backup your The password is now set and protection enabled, although access waypoint data BEFORE password protecting your waypoints.
Page 59: Routes
5.2 Routes • Build and save a route for use when required (stored in the route list). A route is a series of waypoints typically used to assist with passage • Navigate (follow) routes. planning and navigation. • Manage and edit routes stored on the system. A route is displayed on screen as a series of waypoints linked by a line.
Page 60 Building a route using touch 4. Select the appropriate option on the softkey toolbar: • To use an existing waypoint select the USE THIS WAYPOINT softkey. • For a new waypoint select the PLACE WAYPOINT softkey. 5. Repeat Steps 3 to 4 for each subsequent waypoint, until the route is complete.
Page 61: Navigating A Route
1. Position the cursor over the required track. 2. Select the CREATE ROUTE FROM TRACK softkey. 3. Select the YES softkey to name the route, or NO to accept the default route name. A route will be created and the current track will continue to be recorded until you select the STOP TRACK softkey.
Page 62 1. Build your route. Note: You can set the approach distance (radius) at which the waypoint arrival alarm will sound using the alarm setup menu. 2. After adding the final waypoint in your route, press the FOLLOW (QUICK) ROUTE softkey. Advancing to the next waypoint in a route Note: You can stop following a route at any time by pressing the STOP FOLLOW softkey.
Page 63: Erasing A Route
Note: You can delete any route, except for the one that you are currently following. When you erase a route, only those waypoints associated with that route are deleted. Review or edit a route There are a variety of attributes associated with routes. These can be reviewed and edited.
Page 64 • With the chart application active, use the following softkey 1. Using the trackpad, move the cursor over the waypoint you want sequence; Navigation options > Planning > My Routes and to remove. select the required route from the list. 2.
Page 65: Tracks
5.3 Tracks 2. Using the trackpad, select the Chart Setup option. 3. Using the trackpad, select the Route Width menu item. A track is an on-screen trail that shows the route you have taken. 4. Using the trackpad, select the appropriate route line thickness. This trail is made up of a series of track points which are created 5.
Page 66: Erasing A Track
Selecting a track to review or edit Note: If the power fails whilst a track is being recorded or the position fix is lost, a break will occur in the track. Only the last 1. Do one of the following to select the required track: segment of a track can be converted into a route.
Page 67: Waypoints, Routes And Tracks Storage Capacity
5.4 Waypoints, routes and tracks storage • Auto— The track interval is automatically set. capacity • Time— The track points are placed at regular intervals of time. • Distance— The track points are placed at regular intervals of The display can store the following quantities of waypoints, routes distance.
Page 68 E-Series Widescreen User reference...
Page 69: Chapter 6 Using The Chart
Chapter 6: Using the chart Chapter contents • 6.1 Chart application overview on page 70 • 6.2 Vessel position and orientation on page 72 • 6.3 Chart views on page 75 • 6.4 Chart planning options on page 78 • 6.5 Chart navigation options on page 78 •...
Page 70: Chart Application Overview
6.1 Chart application overview The chart application provides an electronic chart with passage planning and navigation features. It combines 2D and 3D viewpoints and provides a variety of cartographic information regarding your surroundings and charted objects. Typical uses for the chart application include : •...
Page 71 , it will automatically correlate each time you change the datum on the multifunction display. • Fish’N Chip • If you have a Raymarine GPS receiver using NMEA0183, or a • Hotmaps third-party GPS receiver, you must correlate it separately.
Page 72: Vessel Position And Orientation
6.2 Vessel position and orientation North Up (N-up) Vessel position on the chart display Your current position is represented on screen by a boat symbol. The boat symbol is shown below: Note: The boat symbol can be customized, so may appear differently on your display.
Page 73 2. Select Chart Setup. Note: It is not possible to select Head Up when the motion mode is set to True. 3. Use the Chart Orientation menu item to select the Head-Up, North-Up, or Course-Up option, as appropriate. Course Up (C-up) Chart motion mode The motion mode controls the relationship between the chart and your vessel.
Page 74 When the motion mode is set to Relative, the position of your vessel Autorange selects and maintains the largest possible scale of chart is fixed on the screen and the chart picture moves relative to your that will display both the vessel and the target waypoint. Autorange vessel.
Page 75: Chart Views
6.3 Chart views The chart is viewed and manipulated in 3 dimensions. It can be viewed from directly overhead (2D view) or at an angle (3D view) • 2D chart view. The chart automatically reverts to 2D mode when viewed directly from above. Item Description •...
Page 76 Item Description Item Description Cartographic objects — use the Cartography Setup menu Range — horizontal distance across screen (halfway to choose which objects to display. up the window or at center of view). Shown in selected system units. AIS target — a vessel broadcasting AIS information. Vessel symbol —...
Page 77 UniControl — is used for pitch, rotate and pan. Range key— is used to zoom in and out. 1. Chart pitch. i. If the chart is in 3D mode, select the Pitch option from the 3. Zoom— Use the range key to zoom in or out of the chart. softkey toolbar 4.
Page 78: Chart Planning Options
6.4 Chart planning options 6.5 Chart navigation options The chart provides features to help plan your navigation to a chosen The chart provides features to help navigate to a chosen location. location. The Navigation Options are found on the chart toolbar softkeys — The options are found on the chart softkeys —...
Page 79: Measuring Distances And Bearings
6.6 Measuring distances and bearings Clearing the chart ruler In the chart application: You can use the databar information and the ruler to measure distances in the chart application. 1. Select the NAVIGATION softkey. You can determine the distance and bearing: 2.
Page 80: Chart Vectors
6.7 Chart vectors Vector descriptions Tide arrow — tide is displayed as a blue line with solid arrow head pointing Chart vectors display indicators for heading and COG, and wind away from your vessel, in the direction of the tidal set. The width of the arrow and tide direction.
Page 81: Current Information
6.8 Current information Controlling current animations In the chart application, with a current animation displayed: Animated current information 1. To start or stop the animation, select the ANIMATION The electronic charts may allow animation of the current information PLAY/PAUSE softkey. current stations.
Page 82: Chart Object Information
6.9 Chart object information 4. To move the time selector, use the trackpad. 5. To change the displayed date, use the appropriate softkeys. You can display additional information on the chart for cartographic objects, ports, and marinas. You can also search for the nearest instance of a particular chart object and search for ports by name.
Page 83: Displaying Panoramic Photos
Displaying chart object information The softkeys change to provide the search object options. 2. Select the SEARCH BY NAME softkey. In the chart application: 3. Select the EDIT NAME softkey. 1. Position the cursor over the object. The on-screen keyboard is displayed. A pop-up is displayed, showing the basic object information.
Page 84: Chart Layers
6.10 Chart layers The chart has a number of content layers and display modes providing different kinds of display and information. You can overlay data onto a chart window to give greater depth of information. The overlays available are: • Aerial overlay. Provides an aerial / satellite photography overlay. •...
Page 85: Radar Overlay
Radar overlay Specifying aerial overlay opacity In the 2D chart view: You can combine the chart with the radar and MARPA functions to provide target tracking or to help you distinguish between fixed 1. Select the 2D CHART LAYERS softkey. objects and other marine traffic.
Page 86 The MARPA-related softkeys are displayed. Range rings 2. Alternatively, with Radar Overlay switched on, press the TARGET TRACKING softkey. Chart scale and radar range synchronization You can synchronize the radar range in all radar windows with the chart scale. When synchronization is switched on: •...
Page 87 intensity of the overlay to achieve optimal visibility of both chart 3. Use the TROPICAL STATEMENTS, MARINE WARNINGS, and weather information. MARINE ZONE FORECASTS, or WATCHBOX WARNINGS softkeys to select the required weather reports. Note: The NOWRad weather overlay can only be used in North America and its coastal waters.
Page 88: Chart Presentation
6.11 Chart presentation Synchronizing multiple chart instances In the chart application: The chart has a number of presentation options which affect the level of detail, types of objects and aspects of its operation. 1. Select the PRESENTATION softkey. The presentation options available are: 2.
Page 89: Chart Detail
Chart Detail 2. Use the CHART DETAIL softkey to select the HIGH or LOW option, as appropriate. The chart detail setting determines the amount of cartographic detail shown in the chart application. Selecting the LOW option for the CHART DETAIL softkey hides the following cartographic objects: •...
Page 90: Chart Setup
6.12 Chart setup The set up for your chart and its cartography can be changed from the standard configuration to suit your particular needs. Although you will probably only do this when you first use the chart, you may decide to make subsequent adjustments once you become more familiar with the system.
Page 91 Chart setup menu options The following table describes the various options in the Chart Setup Menu for your multifunction display. Menu item Description Options Chart Orientation Chart orientation is the relationship between the chart and the direction • Head-Up that you are travelling in. This menu option enables you to choose •...
Page 92 Menu item Description Options 3D set up Settings specific to the 3D chart view: • Center-of-view indicator: • Center-of-view indicator — determines whether a white cross is – ON displayed, indicating the centre of view. – OFF (default) • Trans Cone — displays a transducer cone below the vessel icon, •...
Page 93 Menu item Description Options • Vector Width — sets the width of the COG and HDG (heading) – 3 Mins chart vector lines. – 6 Mins • Route Width — sets the width of route lines. – Infinite (default) • Range Rings — displays radar range rings on the chart display. •...
Page 94 Menu item Description Options Record Vessel Track By Determines how track points are recorded on the chart: • Auto (default) • Time • Auto — track points are automatically created. • Distance • Time — track points are created based on time. •...
Page 95 GPS to the new mode, and indicates whether this was successful or not. Note: Raymarine recommends that you check the displayed vessel position in the chart application against your actual proximity to a known charted object. A typical GPS has an accuracy of between 5 and 15 m.
Page 96 Cartography setup menu options The following table describes the various options in the Cartography Setup Menu for your multifunction display. Menu item Description Options Chart Display Determines the level of detail shown on the chart. • Simple • Detailed (default) •...
Page 97 Menu item Description Options Safety Contour The chart will use this depth as the deep water boundary. Water areas • OFF of depth greater than this will be colored using the appropriate Deep • 7 ft Water Color. • 10 ft •...
Page 98 Menu item Description Options Caution & Routing Data Determines whether caution and routing data is displayed or not. • OFF • ON (default) • OFF — caution and routing data is NOT displayed. • ON — caution and routing data is displayed. Marine Features When this menu item is set to ON, the following water-based •...
Page 99 Menu item Description Options Additional Wrecks Determines whether extended information for new wrecks is displayed. • OFF • ON (default) Aerial Photo Overlay Determines the areas of the chart covered by the aerial photo overlay • On Land (default) feature. •...
Page 100 E-Series Widescreen User reference...
Page 101: Chapter 7 Using Autopilot Control
Chapter 7: Using autopilot control Chapter contents • 7.1 Enabling the autopilot control function on page 102 • 7.2 Disengaging the autopilot in an emergency on page 102 • 7.3 Autopilot control on page 103 • 7.4 Autopilot control options on page 104 •...
Page 102: Enabling The Autopilot Control Function
7.1 Enabling the autopilot control 7.2 Disengaging the autopilot in an function emergency 1. Press the MENU button. While following a route using the autopilot: 2. Select System Setup. 1. Press and release the POWER button. 3. Select System Integration. 2.
Page 103: Autopilot Control
7.3 Autopilot control You must use the physical keys to select these softkeys. You can use your multifunction display to control your autopilot. Engaging the autopilot Note: For information on connecting an autopilot to your In the chart application: multifunction display, refer to the documentation that accompanies the autopilot.
Page 104: Autopilot Control Options
7.4 Autopilot control options 7.5 Autopilot dialog box Your multifunction display enables you to navigate to target The autopilot dialog box provides important information when waypoints using the autopilot control options. navigating using the integrated autopilot controls. When you arrive at a waypoint, the Pilot Control dialog is displayed, The following information is displayed: providing the following options: •...
Page 105: Autopilot Status Symbols
7.6 Autopilot status symbols Symbol Description Autopilot calibration. The autopilot status is indicated in the databar. Symbol Description Power steering active. Autopilot is in Standby mode. Wind Vane mode is active. Autopilot is in Track mode. Autopilot is in Auto mode. No autopilot detected.
Page 106: Autopilot Alarms
7.7 Autopilot alarms The autopilot functions provide alarms to alert you to situations that require action. Your multifunction display shows autopilot alarms, regardless of whether there is active navigation on the system. If pilot integration is enabled, and an alarm is raised by the autopilot, the multifunction display provides an audible alarm sound (providing that the alarm has not already been silenced).
Page 107: Chapter 8 Using Alarms And Mob Functions
Chapter 8: Using alarms and MOB functions Chapter contents • 8.1 Using Man Overboard (MOB) functions on page 108 • 8.2 Alarms on page 109 Using alarms and MOB functions...
Page 108: Using Man Overboard (Mob) Functions
8.1 Using Man Overboard (MOB) Note: To obtain a MOB position, your multifunction display must have a GPS position fix. functions Man overboard Cancelling a MOB alarm If you lose a person or object overboard, you can use the Man 1.
Page 109: Alarms
8.2 Alarms • All other chart controls, including overlays, are set to their default settings. Alarms alert you to a situation or hazard requiring your attention. • MOB position data is displayed in the databar along the top of You can set up alarms to alert you to certain conditions, such as the screen.
Page 110 System alarm setup Menu item Description Options Menu item Description Options Alarm Clock When set to ON, an • OFF (default) alarm is triggered at Anchor Alarm When set to ON, • OFF (default) • ON the time you specify for the anchor alarm is the Alarm Clock Time •...
Page 111: Navigation Alarms Setup
Navigation alarms setup Menu item Description Options Arrival Alarm Radius When you arrive at a 0.01 to 9.99 nm (or waypoint, an alarm is equivalent units) triggered. This setting allows you to specify the distance from the target waypoint at which the alarm is triggered.
Page 112 Menu item Description Options Menu item Description Options Collision Alarm You can set up an alarm • OFF (default) Setup Alarm Zone Enables you to specify zone in front of your the zone for the Collision • ON vessel to alert you to Alarm setting (see charted objects above above).
Page 113: Fishfinder Alarms Setup
Radar alarms setup Setting up the anti-collision alarm zone Menu item Description Options Guard Zones The guard zone feature 0 to 100% Sensitivity in the radar application triggers an alarm when a target is within a specified zone. You can adjust the sensitivity of the alarm.
Page 114 Menu Item Description Options Menu Item Description Options Fish Alarm Depth Limits If the Fish Alarm and OFF, ON Deep Depth Alarm Deep Depth Alarm OFF, ON this alarm is set to ON, Switches the deep depth an alarm is triggered alarm on or off.
Page 115: Chapter 9 Using Radar
Chapter 9: Using radar Chapter contents • 9.1 Radar overview on page 116 • 9.2 HD and SuperHD digital radar scan speed on page 116 • 9.3 Radar scanner status symbols on page 117 • 9.4 Radar range and image quality on page 118 •...
Page 116: Radar Overview
9.1 Radar overview 9.2 HD and SuperHD digital radar scan speed Radar is used to provide information that can help you to track targets and measure distances and bearings. If your scanner supports multiple speeds, you can adjust the scan Radio Detection And Ranging (RADAR) is used at sea to detect the speed.
Page 117: Radar Scanner Status Symbols
9.3 Radar scanner status symbols radar targets. At radar ranges of greater than 3 nm the display switches the radar speed to 24 RPM. The radar scanner power mode status is indicated in the databar. Radar power Symbol mode Description Transmit Rotating icon, signifying that the (TX)
Page 118: Radar Range And Image Quality
9.4 Radar range and image quality Powering the radar scanner on and off In the radar application: Maximum radar range 1. Press the POWER button on your multifunction display. The usable range of the radar is limited by factors such as the 2.
Page 119 Radar image quality A number of factors can affect the quality of a radar image, including echoes, sea clutter, and other interference. Not all radar echoes are produced by valid targets. Spurious echoes may be caused by: • Side lobes. •...
Page 120 Multiple Echoes Multiple echoes are not very common but can occur if there is a large target with a wide vertical surface at a comparatively short range. The transmitted signal will be reflected back and forth between the target and your own ship, resulting in multiple echoes, displayed beyond the range of the true target echo, but on the same bearing.
Page 121: Radar Display Overview
9.5 Radar display overview Interference When two or more radar-equipped vessels are operating within With your radar scanner connected and the radar in transmit mode, range of each other mutual radar interference can occur. This the radar picture provides a map-like representation of the area usually appears as a spiral of small dots from the display centre This in which the radar is operating.
Page 122 • High coastlines and mountainous coastal regions can be observed Item Description at longer radar ranges. Therefore, the first sight of land may be a Ship’s Heading Marker (SHM) mountain several miles inland from the coastline. Although the coastline may be much nearer, it may not appear on the radar Ship’s position until the vessel is closer to shore.
Page 123: Dual Range Radar Operation
9.6 Dual range radar operation Dual range radar compatibility The range covered by the short Dual Range option depends on the The Dual Range radar function enables you to view 2 ranges at the radar scanner you are using, and the software version it is using. same time in separate windows.
Page 124: Radar Mode And Orientation
9.7 Radar mode and orientation Scanner Dual Range mode Operating mode 4 Kw SuperHD Digital Long SuperHD Radar orientation modes Open Array The radar can operate in a number of orientation modes to suit Short different types of navigation. Long 12 Kw SuperHD Digital SuperHD The orientation of the radar refers to the relationship between the...
Page 125 North Up (N-UP) Course Up (C-UP) If you select a new course, the picture will reset to display the new Note: If heading data becomes unavailable whilst in this mode, course upwards. a warning message will be shown, the status bar indicates North-Up in brackets and the radar uses 0°...
Page 126 1. Press the PRESENTATION softkey. 2. Press the RADAR MODE AND ORIENTATION softkey. 3. Using the ORIENTATION softkey, select the required orientation mode. Changing the radar vessel offset In the radar application: 1. Press the PRESENTATION softkey. 2. Press the RADAR MODE AND ORIENTATION softkey. 3.
Page 127: Radar Tuning: Hd And Superhd Digital Scanners
• Buoy — a special mode that enhances the • Gain — enables you to use a preset in automatic picture in different situations. Raymarine strongly detection of small objects like mooring buoys. It is mode, or to adjust its gain manually between 0 recommends the use of these presets to achieve useful at ranges up to 0.75 nm.
Page 128 Tuning method Related options Description – Antenna Boost: scales the effective antenna size. At zero, the effective antenna size matches its actual size. At 95%, the effective antenna size is doubled. Increasing the effective antenna size separates targets that appear merged at lower settings.
Page 129 • AUTO — the default mode. The radar tunes itself The radar tuning control enables you to fine-tune the automatically on all range scales. Raymarine radar scanner’s receiver for maximum target returns recommends that you leave the tune function in on the display.
Page 130 Adjusting digital radar color gain 3. Select the same softkey again. In the radar application: The softkeys change to provide more options. 4. Use the SEA softkey to select the MAN option. 1. Select the GAIN softkey. 5. Using the rotary controller, adjust the gain control to the 2.
Page 131 6. Using the rotary controller, adjust the gain control to the 2. Select the Radar Setup menu item. appropriate setting (between 0 and 100%). 3. Select the Scanner Setup menu item. 7. Press the OK button. 4. Select the Tune menu item. 5.
Page 132: Radar Tuning: Non-Hd Digital Radomes
9.9 Radar tuning: non-HD digital radomes You can use the gain presets and other functions to improve the quality of the radar picture. The following settings apply to non-HD digital radomes: Tuning method Related Options Description Gain • AUTO — the preset operates in automatic mode. Enables you to adjust the sensitivity of the radar This is the default.
Page 133 • MAN — allows you to manually adjust the intensity takes account of land clutter so that smaller targets, to automatic mode by default. Raymarine strongly of the sea gain, from 0 to 100%. like navigation buoys, are not lost.
Page 134 • AUTO — the default mode. The radar tunes itself The radar tuning control enables you to fine-tune the automatically on all range scales. Raymarine radar scanner’s receiver for maximum target returns recommends that you leave the tune function in on the display.
Page 135 Adjusting the radar tune control 1. Press the GAIN softkey. 2. Press the SEA softkey. In the radar application: 3. Select the HARBOR, OFFSHORE, or COASTAL preset, as appropriate. 1. Press the MENU button. 2. Select the Radar Setup menu item. Note: You can adjust the radar’s sensitivity to sea clutter using 3.
Page 136: Using Radar To Measure Distances, Ranges, And Bearings
9.10 Using radar to measure distances, ranges, and bearings When you are using the radar application, you can measure distances, ranges and bearings in a variety of ways. These options are detailed in the table below: Distances Between Range From Measuring using the cursor Functions Points...
Page 137 Note: The default bearing mode for EBLs is relative to your vessel’s heading. If heading data is available, you can set the Measuring using Electronic Bearing Lines (EBLs) bearing mode to be relative (REL), magnetic/true (M/T). When M/T is selected, the EBL bearings will be expressed as either An Electronic Bearing Line (EBL) is a line drawn from your boat to true or magnetic, dependant on the equipment connected.
Page 138 7. Repeat Steps 1 to 6 to create a second VRM/EBL if required, this time using the VRM/EBL 2 softkey. Note: The first VRM/EBL will be placed at a location of 1/3 of the current range and 030° relative to your vessel’s head. If this setting is adjusted, the display will retain the adjustments and use them when the VRM/EBL is next enabled.
Page 139 4. Select the ADJUST VRM softkey. The intersection of the VRM/EBL is placed at this location. 5. Using the rotary control, adjust the VRM to the required size. 5. Place your finger on the intersection between the VRM and EBL, and drag the VRM/EBL to the required position.
Page 140: Using Radar To Track Targets And Avoid Collisions
9.11 Using radar to track targets and avoid collisions There are a number of radar functions to help you track targets and avoid collisions, including Guard Zones, MARPA, and AIS. With a radar connected to your multifunction display, you can: •...
Page 141 MARPA will • The target or your own vessel is making rapid manoeuvres. perform. For the best heading data, a Raymarine SMART heading sensor or a gyro-stabilized autopilot is required.
Page 142 • the symbol wanders away from the target, locks-on to another target, or changes to a lost symbol target. In these circumstances, target acquisition and tracking may need to be re-initiated and in some cases might be impossible to maintain. Better quality heading data might improve performance in these circumstances.
Page 143 Relative mode 5. Press the OK button. With the display set in Relative mode, no vector extension of your MARPA options vessel is shown. The CPA line emerges from your own vessel, with The MARPA options are accessible by pressing the TARGET the target vector extension being shown as relative, not true.
Page 144 1. Move the cursor over the relevant target. Parameter Descriptions Options 2. Press the CANCEL TARGET softkey. Own Vessel Safe Zone The safe zone is a ring, • 0.1 nm 3. Alternatively, display the MARPA target list by pressing the centred on your boat, •...
Page 145: Radar Setup Menu Options
• Tune Adjust — allows you to fine tune the radar scanner’s receiver for maximum • AUTO returns on the display. Raymarine recommends that this function is set to AUTO. • MANUAL If you set this function to MANUAL and adjust the setting shortly after powering...
Page 146 Function Description Options Color Palette (Digital only) The color palette options enable you to customize the look of the radar display for • Bold different situations, as follows: • Professional 1 • Bold — uses high color gain, predominately red, to show weak targets more •...
Page 147: Chapter 10 Using Ais
Chapter 10: Using AIS Chapter contents • 10.1 AIS overview on page 148 • 10.2 AIS prerequisites on page 149 • 10.3 Classes of AIS data on page 150 • 10.4 Enabling AIS on page 151 • 10.5 Displaying AIS vectors on page 151 •...
Page 148: Ais Overview
AIS should be used to complement radar, not substitute it. AIS Simulator Mode Raymarine recommends that you use the simulator to familiarize yourself with the AIS function. When the system simulator is switched on (Menu > System Setup > Simulator), it displays 20 AIS targets within a 25nm range.
Page 149: Ais Prerequisites
10.2 AIS prerequisites Note: Incoming safety messages cannot be displayed while the simulator is switched on. You must have suitable AIS hardware connected to your multifunction display to make use of the AIS functionality. In order to run AIS, you will need: •...
Page 150: Classes Of Ais Data
10.3 Classes of AIS data Class A Class B Class B Data (receive) (send) (receive) There are two classes of AIS data; each class supports a different Draft range of AIS data. Cargo AIS data is defined as Class A or Class B. The sending and receiving of Class A data is compulsory for larger vessels.
Page 151: Enabling Ais
10.4 Enabling AIS 10.5 Displaying AIS vectors You must have the correct data available before AIS vectors can Enabling AIS in the chart application be displayed. In the 2D chart view: A target is defined as active when it has the following data displayed graphically: 1.
Page 152: Ais Status Symbols
10.6 AIS status symbols 10.7 AIS silent mode AIS status is indicated by a symbol in the databar. AIS silent mode enables you to disable AIS transmissions AIS silent mode enables you to disable the transmitting functions Symbol Description of your AIS equipment. This is useful when you do not want to transmit your vessel’s AIS data to other AIS receivers, but still wish AIS unit is switched on and operating.
Page 153: Viewing Ais Target Information
10.8 Viewing AIS target information Target type Description Symbol Dangerous target Targets within specified You can display information relating to individual AIS targets. distance (CPA) or time When a target is highlighted with the cursor, the softkeys change (TCPA). Dangerous to allow you to select the following options: target alarm sounds if enabled.
Page 154: Using Ais To Avoid Collisions
10.9 Using AIS to avoid collisions • Remove the message (ACKNOWLEDGE). • Place a waypoint on your chart / radar to mark the sending You can use the AIS safe zone and safety message functions to vessel’s position. help you avoid collisions with other vessels and objects. •...
Page 155: Ais Options
10.10 AIS options Parameter Description Options Own Vessel Safe Zone The safe zone is a ring, • 0.1 nm The AIS options are accessible in the chart application by pressing centred on your boat, the AIS OPTIONS > MARPA & AIS OPTIONS softkeys, or the radar •...
Page 156: Ais Alarms
10.12 Buddy tracking 10.11 AIS alarms The AIS functions generate a number of alarms to alert you to You can configure your display to notify you when an AIS-equipped dangerous or lost targets. friend or “buddy” comes within range of your vessel. The Buddy Tracking feature enables you to add AIS-equipped In addition to the dangerous target alarm previously described, the system generates an alarm when a dangerous target becomes a...
Page 157 How it works The MMSI and vessel name are automatically added to the Buddy List. When the AIS Layer is enabled in the chart or radar application, AIS targets are shown on your display. You can add any AIS target to Adding a vessel to your buddy list from AIS a “Buddy List”, each entry consisting of an MMSI number, and an optional name.
Page 158 Editing a buddy’s details 6. Select YES to confirm that you wish to delete the buddy, or NO to abort. 1. In the chart or radar application, use the trackpad to move the 7. Press the OK button. cursor over an AIS target. The softkeys change to reflect this and give you Buddy-related Displaying additional buddy information options.
Page 159: Chapter 11 Using The Course Deviation Indicator
Chapter 11: Using the Course Deviation Indicator Chapter contents • 11.1 Course Deviation Indicator overview on page 160 • 11.2 Displaying the CDI application on page 161 • 11.3 Using the CDI application on page 161 Using the Course Deviation Indicator...
Page 160: Course Deviation Indicator Overview
11.1 Course Deviation Indicator overview Screen item Description Starboard steer arrow The Course Deviation Indicator (CDI) gives a graphical representation of your vessel’s course in a ‘rolling road’ format. Water With your display receiving accurate heading and position Horizon information, you can use the Course Deviation Indicator (CDI) to monitor your course and accurately steer to a target waypoint.
Page 161: Displaying The Cdi Application
11.2 Displaying the CDI application 11.3 Using the CDI application 1. Press the HOME button to display the home screen. Monitoring Your Course Using CDI 2. Select a page that includes the CDI application. You can use the ‘rolling road’ format of the Course Deviation The CDI application is displayed.
Page 162 2. Press the GOTO WAYPOINT OPTIONS softkey. The Waypoint List is displayed. 3. Using the trackpad, select the waypoint that you want to go to. 4. Press the GOTO WAYPOINT softkey. Note: Press the STOP GOTO softkey at any time to stop going towards the waypoint.
Page 163: Chapter 12 Using The Fishfinder
Chapter 12: Using the fishfinder Chapter contents • 12.1 Fishfinder introduction on page 164 • 12.2 The sonar image on page 165 • 12.3 Fishfinder presets on page 167 • 12.4 Fishfinder display modes on page 168 • 12.5 Fishfinder range on page 172 •...
Page 164: Fishfinder Introduction
12.1 Fishfinder introduction Fishfinder screen The fishfinder displays a scrolling image of the seabed, updating Warning: Sonar operation from the right as your vessel makes progress. • NEVER operate the sounder with the boat out of Example fishfinder screen the water. •...
Page 165: The Sonar Image
12.2 The sonar image Interpreting the seabed using sonar • Icon animated - fishfinder is operating. It is important to understand how to correctly interpret the seabed structure represented in the fishfinder display. • Icon static - the fishfinder transducer is connected but not transmitting.
Page 166 off the seabed again. This can happen if the water is shallow, the seabed is hard, or the gain is set high. Factors influencing the sonar display The quality and accuracy of the display can be influenced by a number of factors including vessel speed, depth, object size, background noise and transducer frequency.
Page 167: Fishfinder Presets
12.3 Fishfinder presets movement. This is known as ‘background noise’ or ‘clutter’ and is controlled by the gain modes. The system will automatically control the gain settings according to the depth and water conditions. You The fishfinder provides you with four preset configurations available can however adjust the gain settings manually if you prefer.
Page 168: Fishfinder Display Modes
12.4 Fishfinder display modes Selecting a fishfinder preset From the fishfinder main screen: Selecting a fishfinder display mode 1. Press the appropriate softkey to select from: When a fishfinder preset is selected, its softkey label changes to • PRESET 1 SINGLE, ADJUST.
Page 169 • Reposition the zoomed portion of the image to a different point 4. Select the SELECT VIEW softkey. in the display. 5. Select the ZOOM option. When the range increases, the area shown in the zoom window Selecting zoom split screen also increases.
Page 170: Bottom Lock
The standard fishfinder display shows a historical record of fishfinder Enabling the Fishfinder A-Scope Mode echoes. If required, you can display a live image of the bottom From the fishfinder main screen: structure and the fish directly below the transducer by using the A-Scope feature.
Page 171 1. Use the appropriate softkeys and the trackpad to set Full / Split screen, Bottom lock range and Bottom shift values as appropriate. Bottom Lock is selected for individual fishfinder windows and can either replace (ON) or appear alongside (SPLIT) the standard fishfinder image.
Page 172: Fishfinder Range
12.5 Fishfinder range The Range and Range Shift functions enable you to change the range of depth displayed by the fishfinder. Range The Range function enables you to define the range of depth that you see in the fishfinder display. By default, the fishfinder display shows the shallowest required range, enabling you to clearly see what is near the surface of the water under your vessel.
Page 173: Fishfinder Presentation Options
12.6 Fishfinder presentation options image within the current range. Changes to the range shift are reflected in all fishfinder windows. The PRESENTATION softkey gives you access to a features 1. Press the RANGE control to open the range toolbar. and functions which enhance the fishfinder display and provide 2.
Page 174 • Low (Cruising) is ideal for viewing fishfinder images with a 4. Use the rotary control to select the amount of gain you want, minimum of background noise as you are cruising to your fishing between a value of 1 to 100. (The default value is 75). spot.
Page 175 4. Use the rotary control to select the amount of color gain you Adjusting the fishfinder time varied gain want. Note: TVG has no effect in fishfinder simulator mode. 5. Press the OK button. The new values remain set even when you switch off the display 1.
Page 176 Depth and distance with the fishfinder Screen item Description You can use VRM markers and depth lines to help you determine Depth reading — your current depth displayed. The depths and distances in the fishfinder display. size and position of this digit can be changed, using the Fishfinder Display Setup menu.
Page 177 3. Press the VRM softkey to open the VRM toolbar. are looking for fish. If you select a slower speed the information remains on the display for longer. 4. Press the VRM softkey again until the ON option is selected. 5.
Page 178: Fishfinder Waypoints
12.7 Fishfinder waypoints 2. Press the SCROLL softkey to pause the display. 3. Press the OK button. Placing a waypoint on the fishfinder display enables you to mark a position that you can return to later. Dual / Single frequency fishfinder When a waypoint is placed, its details are added to the waypoint list Dual frequency operation allows the sonar to operate and display 2 and a vertical line labelled WPT is displayed on screen.
Page 179: Fishfinder Alarms
12.8 Fishfinder alarms The display can be configured to provide a number of fishfinder alarms. The following fishfinder alarms can be set when you are connected to a DSM, or when the simulator is on: • Fish alarms sound when a target meets the specified sensitivity level and, is within the depth limits (if enabled).
Page 180: Fishfinder Setup
12.9 Fishfinder setup Opening the fishfinder setup menu In the fishfinder application: 1. Press the MENU button. 2. Select the Fishfinder Setup menu item. E-Series Widescreen User reference...
Page 181 Fishfinder setup menu options This section describes the settings you can change using the fishfinder setup menu. The setup menu contains settings that are likely to be changed infrequently. Menu Item Description Options Enables you to adjust the frequencies used for the four fishfinder AUTO or manual frequencies.
Page 182 Menu Item Description Options Color Palette Various color palettes are available to suit different conditions • Classic Blue and your personal preferences. • Classic Black • Classic White • Sunburst • Greyscale • Inverted Greyscale • Copper • Night Vision Manual Scroll Speed Specify the fishfinder scroll speed.
Page 183 4. Make the required changes for each preset mode (P1 to P4) Changing fishfinder preset names 1. From the main fishfinder screen, press the MENU button. 2. Select Fishfinder Setup from the list of options. 3. Select Configure Preset Frequencies from the list of options. 4.
Page 184 Transducer and DSM settings Selecting the DSM and transducer settings From the main fishfinder screen: 1. Press the MENU button. 2. Select Fishfinder Setup from the list of options. 3. Select from the list of menu options: • Transducer Settings •...
Page 185 Fishfinder Transducer Calibration Your fishfinder transducer must be calibrated correctly to achieve accurate depth readings. The multifunction display receives the image from a DSM which processes sonar signals from a transducer mounted in the water. If the transducer is equipped with a speed paddle wheel and temperature-sensing thermistor, the DSM calculates speed and temperature.
Page 186 Menu Item Description Options Frequency Calibration Fine tune the frequency of the transducer. Variable setting for the selected frequency. Depth Offset (waterline) Offset represents the depth of the transducer (relative to the –9.9 to +9.9 feet waterline). Speed Offset Offset applied to the speed log. 0 to 100% Temperature Offset Offset applied to the temperature transducer value.
Page 187: Chapter 13 Using The Engine Application
Chapter 13: Using the engine application Chapter contents • 13.1 Engine application overview on page 188 • 13.2 Displaying the engine application on page 188 • 13.3 Setting up the engine application on page 189 • 13.4 Changing the engine panel dial color on page 189 •...
Page 188: Engine Application Overview
If the default range of data shown by the engine application is not suitable, you can change what is displayed. Note: For details of compatible engines and related software updates, please refer to the Raymarine website at www.raymarine.com. E-Series Widescreen User reference...
Page 189: Setting Up The Engine Application
13.3 Setting up the engine application 13.4 Changing the engine panel dial color In the engine application: In the Engine application: 1. Press the MENU button. 2. Select Panel Setup Menu . 1. Press the MENU button. 3. Select Number of Engines , then select the appropriate value. 2.
Page 190: Pre-Configured Data Panels
13.5 Pre-configured data panels By default, a pre-configured range of data is displayed in a number of data ’panels’. Each panel consists of a number of ’cells’, each containing a different item of data. Note: Panel selection is a local setting, and therefore only affects the individual display that you are currently using.
Page 191 List of pre-configured engine panels A range of pre-configured panels show commonly used data. The following table shows the data displayed by each type of panel. Each data item listed in the table below represents a ’cell’. Note: Panel selection is a local setting, and therefore only affects the individual display that you are currently using. It does not affect any networked displays.
Page 192: Changing What The Engine Application Displays
13.6 Changing what the engine Changing the size of data panels application displays In the data or engine application: 1. Press the MENU button. In the engine application: 2. Select Panel Setup Menu. 1. Press the MENU button. 3. Select the data panel you want to resize (Configure...). 2.
Page 193: Chapter 14 Using The Data Application
Chapter 14: Using the data application Chapter contents • 14.1 Data application overview on page 194 • 14.2 Pre-configured data panels on page 195 • 14.3 Airmar WeatherStation data on page 197 • 14.4 Trim tab calibration on page 198 •...
Page 194: Data Application Overview
14.1 Data application overview The data application displays system and instrument data on your multifunction display. The data application enables you to view numeric data generated by the system. It also shows data from instruments connected to your multifunction display using the NMEA or SeaTalk protocols. E-Series Widescreen User reference...
Page 195: Pre-Configured Data Panels
14.2 Pre-configured data panels By default, a pre-configured range of data is displayed in a number of data ’panels’. Each panel consists of a number of ’cells’, each containing a different item of data. Note: Panel selection is a local setting, and therefore only affects the individual display that you are currently using.
Page 196 List of pre-configured data panels A range of pre-configured panels show commonly used data. The following table shows the data displayed by each type of panel. Each data item listed in the table below represents a ’cell’. Note: Panel selection is a local setting, and therefore only affects the individual display that you are currently using. It does not affect any networked displays.
Page 197: Airmar Weatherstation Data
Data Navigation panel Waypoint panel Route panel Fishing panel Sailing panel Trip Local Time Sea Temperature Ground Wind App Wind True Wind VMG Wind 14.3 Airmar WeatherStation data Selecting a pre-configured data panel In the data or engine application: The data, engine, and CDI applications can display temperature data from a compatible Airmar®...
Page 198: Trim Tab Calibration
14.4 Trim tab calibration • True wind chill. • UTC date and time. You can calibrate your trim tabs from your multifunction display. Trim tab data can be displayed in the Engine, Data, and CDI Displaying Airmar WeatherStation data applications by selecting it from the Engine Data Group, using the Panel Setup Menu.
Page 199: Customizing The Data Application
14.5 Customizing the data application 7. Select the appropriate menu items to choose the relevant data type for that particular data. You can customize the data application to show the system and Note: You can also access the SELECT DATA softkey by instrument data that you require.
Page 200 E-Series Widescreen User reference...
Page 201: Chapter 15 Using The Weather Application (North America Only)
Chapter 15: Using the weather application (North America only) Chapter contents • 15.1 Weather application overview on page 202 • 15.2 Displaying the weather application on page 202 • 15.3 Weather application setup on page 203 • 15.4 Weather application display overview on page 203 •...
Page 202: Weather Application Overview
By using this service, you release and waive any claims against Sirius Satellite Radio Inc., WSI, Navcast Incorporated, and Raymarine with regard to this service. If you do not have the subscription agreement, you may view a copy on the internet at www.sirius.com/marineweather...
Page 203: Weather Application Setup
(ESN). This number is located on the weather receiver shipping carton, or on the back of the weather receiver itself. For more information, refer to www.sirius.com. • Your multifunction display must be connected to a Raymarine SR100 Sirius weather receiver. • You must be navigating within US coastal waters.
Page 204 Surface pressure symbols The weather application uses a range of symbols to represent different surface pressure conditions. Surface observation station symbols The weather application uses a range of symbols to represent different types of surface obervation station. Storm tracks symbols The weather application uses a range of symbols to represent different types of storm tracks.
Page 205 Wave information symbols The weather application uses a range of symbols to represent different types of wave information. NOWRad precipitation color codes NOWRad displays the type and level of precipitation: Using the weather application (North America only)
Page 206 Color code Precipitation type Intensity Color code Intensity in mm per hour Light green Rain (15 to 19 dBz) Yellow 12.01 to 24.00 mm/hr Medium green Rain (20 to 29 dBz) Orange 24.01 to 50.00 mm/hr Dark Green Rain (30 to 39 dBz) Light red 50.01 to 100 mm/hr Yellow...
Page 207: Weather Map Navigation
15.5 Weather map navigation 15.6 Weather reports You can move around the weather map and place waypoints. You can view a number of different weather reports to give you a comprehensive view of the weather. When you open the weather application, a world map is displayed. If the system has a position fix for your boat, the map will be centred Your multifunction display shows weather reports for: on your boat.
Page 208: Storm Tracking
15.7 Storm tracking Displaying weather reports In the weather application: The storm tracking function enables you to monitor significant storms in the area. 1. Press the WEATHER REPORTS softkey. Examples of significant storms include tropical disturbances, 2. Select the TROPICAL STATEMENTS, MARINE WARNINGS, depressions, storms and cyclones, hurricanes, typhoons, and super MARINE ZONE FORECASTS, or WATCHBOX WARNINGS typhoons.
Page 209: Animated Weather Graphics
15.8 Animated weather graphics You can view animated weather graphics to provide an indication of changing weather patterns. The animated weather option enables you to view an animation from the current time for: • The forecast for wind, wave, or surface pressure. •...
Page 210 E-Series Widescreen User reference...
Page 211: Chapter 16 Using Sirius Satellite Radio (North America Only)
Chapter 16: Using Sirius satellite radio (North America only) Chapter contents • 16.1 Sirius radio overview on page 212 • 16.2 Displaying the Sirius radio application on page 212 • 16.3 Sirius radio basic operations on page 213 • 16.4 Sirius radio presets on page 214 •...
Page 212: Sirius Radio Overview
16.1 Sirius radio overview 16.2 Displaying the Sirius radio application You can use your multifunction display to control a connected Sirius Satellite Radio receiver. 1. Press the HOME button to display the home screen. Your multifunction display provides access to basic and advanced 2.
Page 213: Sirius Radio Basic Operations
16.3 Sirius radio basic operations 3. Select the TUNE TO CHANNEL softkey to listen to the selected channel. You can tune, browse, and scan Sirius Radio channels using your multifunction display. Scanning Sirius radio channels Tuning and browsing In the Sirius Satellite Radio application: You can tune to a channel using the following methods: 1.
Page 214: Sirius Radio Presets
16.4 Sirius radio presets Deleting a Sirius radio channel from a preset In the Sirius Satellite Radio application: You can assign up to 18 Sirius Radio channels to presets to make it easier to find commonly used channels. 1. Select the PRESETS softkey. Each channel must be assigned to a different preset.
Page 215: Favorite Sirius Radio Song Alerts
16.5 Favorite Sirius radio song alerts 1. Select the ALERTS softkey. The Edit Alerts dialog is displayed. The favorites feature alerts you when a favorite song or artist is 2. Select the ADD SONG or ADD ARTIST softkey, as appropriate. playing on any Sirius Radio channel.
Page 216: Sirius Radio Parental Locking
16.6 Sirius radio parental locking 2. Select the EDIT CHANNEL ACCESS softkey. The Channel List is displayed. You can block certain Sirius Radio channels to prevent unauthorized 3. Select the channel you want to block access to. access. 4. Select the LOCKED option with the CHANNEL When you enable the “Parental Locking”...
Page 217: Chapter 17 Using Navtex
Chapter 17: Using Navtex Chapter contents • 17.1 Navtex overview on page 218 • 17.2 Navtex setup on page 218 • 17.3 Viewing and managing Navtex messages on page 219 Using Navtex...
Page 218: Navtex Overview
17.1 Navtex overview 17.2 Navtex setup The Navtex features enable you to view marine safety information, In order to receive Navtex alerts on your multifunction display, you including weather forecasts and marine safety warnings. must connect a Navtex receiver and configure the NMEA options on your multifunction display.
Page 219: Viewing And Managing Navtex Messages
17.3 Viewing and managing Navtex 4. Set the receive status to ON or OFF, as appropriate. messages 5. Repeat Steps 3 to 4 for each category, as appropriate. Viewing a Navtex message 1. Display the Navtex Message List: i. Press the MENU button. ii.
Page 220 E-Series Widescreen User reference...
Page 221: Chapter 18 Using Video
Chapter 18: Using video Chapter contents • 18.1 Video application overview on page 222 • 18.2 Using video on page 223 Using video...
Page 222: Video Application Overview
18.1 Video application overview You can also output anything displayed on your multifunction display to an external display. The output resolution can be adjusted in the MENU > Display Setup Menu. You can view a video or camera source on your multifunction display. The video application enables you to connect a video source directly Note: You can only view the video on the multifunction display to your multifunction display, and view the video on the screen.
Page 223: Using Video
18.2 Using video 1. Select the VIDEO 1, VIDEO 2, VIDEO 3, or VIDEO 4 softkey to view the relevant video source. Displaying the video application Cycling video sources 1. Press the HOME button to display the home screen. In the video application: 2.
Page 224 E-Series Widescreen User reference...
Page 225: Chapter 19 Dsc Vhf Radio Integration
Chapter 19: DSC VHF radio integration Chapter contents • 19.1 Using a DSC VHF radio with your display on page 226 • 19.2 Enabling DSC VHF radio integration on page 227 DSC VHF radio integration...
Page 226: Using A Dsc Vhf Radio With Your Display
19.1 Using a DSC VHF radio with your display You can connect your DSC VHF radio to your multifunction display and show distress message information and GPS position data for other vessels. Connecting a DSC VHF radio to your multifunction display provides the following additional functionality: •...
Page 227: Enabling Dsc Vhf Radio Integration
19.2 Enabling DSC VHF radio integration To configure your multifunction display to show messages from your DSC VHF radio: 1. Press the MENU button. 2. Select the System Setup menu item. 3. Select the System Integration menu item. 4. Select the ON option for the DSC Message menu item. 5.
Page 228 E-Series Widescreen User reference...
Page 229: Chapter 20 Customizing Your Display
Chapter 20: Customizing your display Chapter contents • 20.1 Customizing the vessel icon on page 230 • 20.2 Customizing the databar on page 231 • 20.3 System setup menu on page 232 Customizing your display...
Page 230: Customizing The Vessel Icon
20.1 Customizing the vessel icon Vessel icon Vessel type Chart view Sail — large In the chart application: 1. Press the MENU button. 2. Select Chart Setup. 3. Select Vessel Icon Type Sail — large 4. Select the Sail or Power option, as appropriate. 5.
Page 231: Customizing The Databar
20.2 Customizing the databar ii. Using the trackpad, select the desired position in the databar for the new data. iii. Select the ADD DATA softkey. Moving the databar iv. Select the data group that contains the type of data you want 1.
Page 232: System Setup Menu
20.3 System setup menu The following table describes the various options in the System Setup menu for your multifunction display. Menu item Description Options Position Mode Determines how positioning data is displayed — as • Lat/Long (default) Latitude/Longitude coordinates, or Loran TDs. •...
Page 233 Menu item Description Options Variation Source This setting compensates for the naturally occuring offset • Auto (compensation value displayed in of the earth’s magnetic field. When set to Auto, the system brackets) (default) automatically compensates, and displays the compensation • Manual value in brackets.
Page 234 Menu item Description Options Settings and Data Reset Resets all system setup menus, including page sets and the Factory Reset confirmation databar, to the factory default settings. Waypoints, routes and • YES tracks ARE deleted. • NO Note: For systems using multiple multifunction displays (networked displays), the complete system database is deleted on the data master (primary display).
Page 235 Menu item Description Options Units Setup Enables you to specify the units used for the following key Distance Units measurements: • Nautical Miles (default) • Distance • Statute Miles • Speed • Kilometers • Depth Speed Units • Temperature • Knots (default) •...
Page 236 Menu item Description Options • Liters System Integration Determines the connection settings for external equipment. The Autopilot Control following items are available in the sub-menu: • Disabled (default) • Autopilot Control — If set to Enabled, this option allows you •...
Page 237 Menu item Description Options to OFF to ensure that all NMEA-connected units receive • OFF (default) heading data from the external heading sensor. • ALL • SeaTalk2 Keyboard — Set to ONE or ALL if you have a SeaTalk2 keyboard connected. Otherwise, set to OFF. •...
Page 238 Menu item Description Options • VTG • ZDA NMEA Port Setting • NMEA 4800 (default) • Navtex 4800 • Navtex 9600 • AIS 38400 Waypoint Password Setup This menu allows you to enable password protection for Enable Password waypoints, and to change the password. •...
Page 239: Chapter 21 Maintaining Your Display
Chapter 21: Maintaining your display Chapter contents • 21.1 Service and maintenance on page 240 • 21.2 Routine equipment checks on page 240 • 21.3 Cleaning on page 241 • 21.4 Cleaning the display case on page 241 • 21.5 Cleaning the display screen on page 242 •...
Page 240: Service And Maintenance
21.1 Service and maintenance This product contains no user serviceable components. Please Raymarine strongly recommends that you complete a number of refer all maintenance and repair to authorized Raymarine dealers. routine checks to ensure the correct and reliable operation of your Unauthorized repair may affect your warranty.
Page 241: Cleaning
21.3 Cleaning 21.4 Cleaning the display case Best cleaning practices. The display unit is a sealed unit and does not require regular cleaning. If it is necessary to clean the unit, follow this basic When cleaning this product: procedure: • Do NOT wipe the display screen with a dry cloth, as this 1.
Page 242: Cleaning The Display Screen
21.6 Resetting your display 21.5 Cleaning the display screen A coating is applied to the display screen. This makes it water Your display may be reset to its factory default settings if required. repellent, and prevents glare. To avoid damaging this coating, follow Your multifunction display may be restored to its factory default this procedure: settings.
Page 243 Performing a settings and data reset Performing a settings and data reset erases ALL waypoints, routes, and track data from your multifunction display. BEFORE proceeding with a settings and data reset, ensure that you backup any data that you want to keep on to a CompactFlash card.
Page 244 E-Series Widescreen User reference...
Page 245: Chapter 22 Technical Support
Chapter 22: Technical support Chapter contents • 22.1 Raymarine technical support on page 246 • 22.2 3rd party support on page 247 Technical support...
Page 246: Raymarine Technical Support
Web support Please visit the customer support area of our website at: www.raymarine.com This contains Frequently Asked Questions, servicing information, e-mail access to the Raymarine Technical Support Department and details of worldwide Raymarine agents. Telephone support In the USA call:...
Page 247: 3Rd Party Support
22.2 3rd party support Contact and support details for 3rd party suppliers can be found on the appropriate websites. Navionics www.navionics.com Sirius marine weather www.sirius.com/marineweather Sirius audio www.sirius.com Technical support...
Page 248 E-Series Widescreen User reference...

This manual is also suitable for:

E120w E140w

Raymarine E90W User Reference Handbook

Chapter 1 Important Information

Chapter 2 Handbook Information

Chapter 3 Getting Started

Chapter 4 Managing Display Data

Chapter 5 Using Waypoints, Routes and Tracks

Chapter 6 Using the Chart

Chapter 7 Using Autopilot Control

Chapter 8 Using Alarms and MOB Functions

Chapter 9 Using Radar

Chapter 10 Using AIS

Chapter 11 Using the Course Deviation Indicator

Chapter 12 Using the Fishfinder

Chapter 13 Using the Engine Application

Chapter 14 Using the Data Application

Chapter 15 Using the Weather Application (North America Only)

Chapter 16 Using Sirius Satellite Radio (North America Only)

Chapter 17 Using Navtex

Chapter 18 Using Video

Chapter 19 DSC VHF Radio Integration

Chapter 20 Customizing Your Display

Chapter 21 Maintaining Your Display

Chapter 22 Technical Support

Quick Links

Need help?

Questions and answers

Related Manuals for Raymarine E90W

Summary of Contents for Raymarine E90W