Download
Share
Print this page
  1. Manuals
  2. Brands
  3. CANTERBURY Manuals
  4. Plumbing Product
  5. OFFICINA NICOLAZZI Z2509
  6. Manual

CANTERBURY OFFICINA NICOLAZZI Z2509 Manual

Classic prov basin set w/cross handle
Hide thumbs

Advertisement

Quick Links

Download this manual
Specifications
• Handmade in Italy since 1960
• ¼ Turn valves handmade at
Nicolazzi Factory
• Lead Free Brass Compliant to
AZ/NZS 3718
• Suitable even and uneven
pressure
• Handles are interchangeable
Further information Phone (03) 9761 4603
Classic Prov Basin set w/Cross Handle
Art: Z2509
Available replacement
handles:
WM22315
AS/NZS3662
Canterbury Sink & Tap Co.
Max/Min Operating
Pressure: 100/500kPa
sales@sinkandtap.com.au

Advertisement

loading
Need help?

Need help?

Do you have a question about the OFFICINA NICOLAZZI Z2509 and is the answer not in the manual?

Questions and answers

Related Manuals for CANTERBURY OFFICINA NICOLAZZI Z2509

Summary of Contents for CANTERBURY OFFICINA NICOLAZZI Z2509

  • Page 1 • ¼ Turn valves handmade at Nicolazzi Factory • Lead Free Brass Compliant to AZ/NZS 3718 • Suitable even and uneven pressure WM22315 AS/NZS3662 • Handles are interchangeable Canterbury Sink & Tap Co. Max/Min Operating Pressure: 100/500kPa Further information Phone (03) 9761 4603 sales@sinkandtap.com.au...
  • Page 2 Important Notice Model : Z2509 CAREFULLY READ THROUGH THESE INSTRUCTIONS BEFORE INSTALLATION AND USE OF ALL TAP WARE AND WALL VALVES INSTALLATION and WARRANTY INSTRUCTIONS TECHNICAL INFORMATION All flexible hoses are designed and manufactured for use with water in exposed locations only. Do not expose to household cleaners, chlorine, chloride, hydrochloric acid or other corrosive chemicals.
  • Page 3 Installation Instructions Model : Z2509 ❶ Preparation Tap body  Flush out the pipework to remove any foreign matter.  Tap body cut out hole sizes : Maximum 40mm diameter.  Under side clearance : Maximum 70mm Tap section  Tap section cut out hole sizes : Maximum 32mm diameter.
  • Page 4 Installation Instructions Model : Z2509  Install the pop-up waste body top section 1, and waste ❶ body bottom section 4, to the basin as shown.  Ensure that the top seal 2, and bottom seal 3, are installed correctly, to ensure proper functioning of the pop-up waste system and prevent any water leakage.
  • Page 5 Installation Instructions Model : Z2509  Fit the tap cover cap 8, over the ceramic ❹ cartridge and longrest securing nuts.  Place the handle 9, carefully onto the cartridge spline.  Once the handle 9, is positioned at the desired orientation, fit the retaining screw 10, into the recess on the top of the handle.
  • Page 6 Installation Instructions Model : Z2509 ❼  Feed the rubber ring 16, over the water supply hoses.  Note: Insert the tap into mounting hole carefully. Feed the water supply hoses through the cut out hole ensuring that they are not bent or kinked, as this could result in permanent damage or leakage.
  • Page 7 Installation Instructions Model : Z2509 ❾  Check the position on the sink of the tap, then tighten the nut using a 13mm spanner or smooth jawed shifter. Note: the under deck mounting surface must be flat. If the mounting surface is irregular, the nut may not be secured, and the tap will be loose on the sink.
  • Page 8 Installation Instructions Model : Z2509 ⓬  Install the vertical waste pop-up rod 22, by feeding it through the hole in the top of the tap body.  Feed the bottom end of the vertical pop-up rod onto the articulated joint 23, located on the horizontal waste pop-up rod.
  • Page 9 Spare Parts list Model : Z2509 Further information Phone (03) 9761 4603 sales@sinkandtap.com.au...
  • Page 10 Care and Maintenance Instructions Model : Z2509 Removing and replacing a handle MODEL SHOWN :Z2509 ❶   ❷ Unscrew and remove the indice button Using a Philips head screw driver, unscrew A, from the tap handle body. the handle retaining screw. ...
  • Page 11 Care and Maintenance Instructions Model : Z2509 MAINTENANCE FOR THREE HOLE/TWO LEVER TAPWARE INSTRUCTIONS FOR REPLACEMENT OF THE HOT OR COLD CARTRIDGE Do not replace the cartridge if there is low flow or no flow. Low flow or no flow is caused by obstruction or kinking of supply hoses.
  • Page 12 Care and Maintenance Instructions Model : Z2509 LOW FLOW OR NO FLOW TROUBLESHOOTING INSTRUCTIONS Current bathroom taps have a max flow rate of 7 Litres per minute from the aerator and the hand spray. If you are experiencing low flow from the spout: Do not change the cartridge •...
  • Page 13 Care and Maintenance Instructions Model : Z2509 Care of external finishes Nicolazzi products are all authentic finishes that have not been coated with any product. After each use, pat the fixture down to remove any excess water. This will prevent any water spotting or mineral build-up. Use only soft liquid soap and water to clean the surface.