Page 1 KOLEOS vehicle user manual...
Page 2 Castrol, exclusive Renault partner Benefit from cutting-edge technology born out of competition to ensure the performance and longevity of your Renault thanks to wide range of engine lubricants developed specially by Renault and Castrol. Renault recommends renault.com...
Page 3 Welcome to your new vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. –...
Page 4 EXTERIOR Rear view mirrors Electric windows ➥ 3.21 ➥ 1.81 Windscreen wipers ➥ 1.92 and ➥ 1.98 Demisting ➥ 3.4 and ➥ 3.7 Key/Remote control ➥ 1.2 Map ➥ 1.5 Locking/unlocking the doors ➥ 1.13 Bodywork maintenance ➥ 4.15 Tyres ➥ 5.10 Lights: operation ➥...
Page 5 PASSENGER COMPARTMENT Passenger compartment storage/fit- Adjusting your driving po- tings ➥ 3.28 sition ➥ 1.26 Rear bench seat ➥ 3.35 Rear headrests ➥ 3.34 Front seats ➥ 1.20 Front headrests ➥ 1.19 Child safety ➥ 1.38 Luggage compartment stor- age/fittings ➥ 3.47...
Page 6 DRIVER’S POSITION Trip computer controls ➥ 1.66 Instrument panel ➥ 1.58 Exterior lighting ➥ 1.84 M u l t i m e d i a s c r e e n ➥ 3.51 Heating/Air conditioning Cruise control ➥ 2.70 system ➥ 3.7 Stop and Go adaptive cruise control ➥...
Page 7 DRIVING AIDS ABS (anti-lock braking system) ESC (electronic stability control) Braking assistance Speed limiter ➥ 2.67 Hill start assistance ➥ 2.32 Cruise control ➥ 2.70 Stop and Go adaptive cruise con- Lane departure warning ➥ 2.52 trol ➥ 2.74 Parking distance control ➥ 2.82 Active emergency braking...
Page 8 SAFETY ON BOARD Inhibiting the front pas- senger airbag ➥ 1.51 Front Airbags ➥ 1.31 Curtain Airbags ➥ 1.36 Side Airbags ➥ 1.36 Seat belts ➥ 1.26...
Page 9 IDENTIFYING A VEHICLE - LABELS Review of a vehicle identification number ➥ 6.2 Technical Information for the emer- gency services ➥ 6.3 Engine identification plate ➥ 6.4 Tyre pressure labels ➥ 2.29 ➥ 4.11 Vehicle identification plate ➥ 6.2...
Page 10 THE ENGINE COMPARTMENT (routine maintenance) Coolant level ➥ 4.8 Brake fluid ➥ 4.8 Windscreen washer fluid ➥ 4.8 Engine oil filler cap ➥ 4.5 Battery ➥ 4.13 Engine oil dipstick ➥ 4.4 Opening the bonnet ➥ 4.2...
Page 11 BREAKDOWN RECOVERY Replacing windscreen wiper Puncture: blade(s) ➥ 5.27 Tools ➥ 5.7 Emergency spare wheel ➥ 5.2 Changing wheel ➥ 5.8 Front towing point ➥ 5.29 Replacing the rear screen wiper blade ➥ 1.98 Replacement of the direc- tion indicator lights ➥ 5.14 Fuses ➥...
Page 12 0.10...
Page 13 Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........0.11...
Page 14 0.12...
Page 15: Table Of Contents
RENAULT card: general information, use, deadlocking ........
Page 16: Key, Radio Frequency Remote Control: General Information, Use
KEY, RADIO FREQUENCY REMOTE CONTROL: general information (1/2) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves 1 Locks all the opening elements.
Page 17 KEY, RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the surround- ings: take care not to lock or unlock the doors by inadvertently pressing the but- tons on the remote control. Replacement and additional keys Note: If a door or the boot is open or or remote controls.
Page 18 RADIO FREQUENCY REMOTE CONTROL UNIT: use Note: The remote control A can be used to lock or unlock the doors and boot. With the engine running, the ignition It is powered by a battery which must switched on and in accessories posi- be replaced.
Page 19 This varies according to the surroun- (see the following pages); dings. It is important to make sure when handling the RENAULT card that you – switching on the vehicle lighting re- do not lock or unlock the doors by inad- motely (refer to the following pages);...
Page 20 (2/3) Advice Avoid leaving the card in hot, cold or humid areas. Do not keep the RENAULT card in a place where it could be bent or damaged accidentally, such as in a back pocket of a garment. Driver’s responsibility...
Page 21 RENAULT CARD: general information (3/3) Fitting a strap 7 Insert the strap into the 8 component and pass the end of the strap through Slide the the rear casing 5 downwards the buckle. while pressing on zone A. Position the strap at the 6 opening and close the cartridge.
Page 22 It allows locking/unlocking without input on the card RENAULT when within the They may pose a risk to themselves access zone 1. or to others by starting the engine,...
Page 23 “Hands-free” unlocking Remote “Hands-free” locking you have to wait approximately With the RENAULT card in zone 1, With the RENAULT card on you, and 3 seconds to be able to unlock the press the button 2 on the handle of one doors and boot closed, move away vehicle again.
Page 24 6, the message Keycard not detected indicates that Unlocking with the card RENAULT the card is not inside the vehicle. This Press the button 4. avoids you driving away after having...
Page 25 RENAULT CARD: usage (4/4) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves...
Page 26 CARD: deadlocking Depending on the vehicle, the door mir- rors fold in automatically when the vehi- cle is locked. ➥ 1.81 Special feature The deadlocking cannot be activated when the hazard warning lights or the side lights are lit. To deactivate deadlocking Unlock the vehicle using button 1 on the card.
Page 27 In some cases, the radio frequency card to unlock the front left-hand remote control or the RENAULT card door; may not work: – to lock each of the doors manually;...
Page 28 Access key 4 integrated in the card or unlock the front left-hand door. Slide the rear casing 3 downwards Once you are inside the vehicle, put the while pressing on zone A. key back in its casing in the RENAULT card. 1.14...
Page 29 6 for more than five seconds. When the door is closed, all the doors and the tailgate will be locked. Unlocking the vehicle from the outside is only possible with the RENAULT card in the vehicle’s access zone or using the key. Interior locking/unlocking The switch 6 controls the doors and the boot simultaneously.
Page 30: Opening And Closing The Doors
Special feature on vehicles If the vehicle is not equipped with the opening elements (door, boot) are open equipped with a RENAULT card knob 3, pull the handle 4. or incorrectly closed. With the doors locked, press button 2...
Page 31 OPENING AND CLOSING THE DOORS (2/2) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves Vehicle with manual door locking or to others by starting the engine, activating equipment such as the...
Page 32: Automatic Locking When Driving
AUTOMATIC LOCKING WHEN DRIVING Activating/deactivating the Operating faults function If you experience an operating fault (no automatic locking, the indicator light in- To switch it on: with the vehicle at a corporated in switch 1 does not light up standstill and the engine running, press when trying to lock the doors and tail- the switch 1 until a beep sounds.
Page 33 FRONT HEADRESTS To raise the headrest To adjust side supports B To remove the headrest Pull the headrest upwards to the de- Depending on the vehicle, sections B Raise the headrest to its highest po- sired height. Check that it is correctly can be adjusted independently to the sition (tilt the seatback backwards if locked.
Page 34 FRONT SEATS WITH MANUAL CONTROL Operating faults When an operating fault is detected, the integrated warning lights on the switch 4 for the seat concerned flash. Consult an approved dealer. To move the seat forwards or Heated seats backwards With the ignition on: Lift handle 1 to unlock.
Page 35 FRONT SEATS WITH ELECTRIC CONTROLS (1/3) To adjust the seat’s lumbar position Lower the handle 3 to increase the sup- port and lift to decrease it. For safety reasons, carry out any adjustments when the vehicle is not being Adjusting the seat squab: driven.
Page 36 FRONT SEATS WITH ELECTRIC CONTROLS (2/3) Adjusting the seat position To move the seat forwards or back- wards Move switch 7 forwards or backwards. To raise or lower the seat base Move the back of switch 7 up or down. Adjusting the seat length Lift handle 8 to unlock.
Page 37 FRONT SEATS WITH ELECTRIC CONTROLS (3/3) With the ignition on: – pressing the switch 11 on the re- quired seat for the first time activates the ventilation system at maximum power. Both integrated switch warn- ing lights come on; – a second press decreases the ven- tilation to minimum power.
Page 38 FRONT SEATS: functions (1/2) Massage Settings Massage Easy access driver Position Tonic Relaxing Lumbar Intensity Speed Massage Settings Using the multifunction screen, de- pending on the vehicle you can access You can activate the driver seat mas- Using the multifunction screen, select a number of seat functions.
Page 39 The driving position can be stored and Recall recalled by pressing the buttons: Save – RENAULT hands-free card detected; – when the driver’s door is opened. Storing your driving position Recalling the driving position – Adjust the seat using switches 3, 4 With the vehicle at a standstill, using and 5 (refer to previous page);...
Page 40: Seat Belts
SEAT BELTS (1/5) Always wear your seat belt when trav- Before starting, first adjust your driv- elling in your vehicle. You must also ing position, then ask all occupants to adjust their seat belts to ensure comply with the legislation of the par- ticular country you are in.
Page 41 SEAT BELTS (2/5) Locking – move the chest strap 1 as close as possible to the base of the neck Unwind the belt slowly and smoothly without it actually resting against it and ensure that buckle 3 locks into (if necessary, adjust the height of the catch 5 (check that it is locked by pull- seat belt if available) and make sure ing on buckle 3).
Page 42 SEAT BELTS (3/5) ß Driver’s seat belt reminder and, depending on the vehi- cle, front passenger seat belt re- minder This lights up on the central display when starting the engine then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approxi- mately 12 mph (20 km/h), it flashes and...
Page 43 SEAT BELTS (4/5) Adjusting the height of the Rear seat belts 8 front seat belts The belts are locked, unlocked and adjusted in the same way as the front Use button 7 to adjust the seat belt belts. height so that the shoulder strap is worn as shown previously.
Page 44 SEAT BELTS (5/5) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...
Page 45 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt inertia reel pretensio- an accident. ners; – No operation whatsoe- –...
Page 46 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Front airbags for driver and passenger Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger side. the belt against the body so that it is at The presence of this equipment is in- an acceptable level.
Page 47 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operating faults å This warning light will light up on the instrument panel when the ignition is switched on and then go out after a few seconds. If it does not light up when the ignition is switched on, or comes on when the engine is running, there is a fault in the system.
Page 48 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...
Page 49 METHODS OF RESTRAINT IN ADDITION TO THE REAR SIDE SEAT BELTS Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...
Page 50 SIDE PROTECTION DEVICES Side Airbags An airbag can be fitted to each front seat, which are deployed on the side of the seat (door side) to protect the oc- cupants in the case of a severe side impact. Curtain Airbags These are airbag fitted along the sides of the vehicle in the ceiling which trigger along the front and rear door side win-...
Page 51: Additional Methods Of Restraint
ADDITIONAL METHODS OF RESTRAINT Operating faults All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused å by items which may be dislodged when it inflates. This warning light comes on when the engine is started and then The airbag is designed to complement the action of the seat belt.
Page 52: Child Safety: General Information
CHILD SAFETY: General information (1/2) Carrying children Please ensure that you comply with the legislation of your country. Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. Driver’s responsibility A child is not a miniature adult.
Page 53 CHILD SAFETY: General information (2/2) Using a child seat Before fitting a child seat, read the manual and respect its instructions. If The level of protection offered by the you experience any difficulties during child seat depends on its ability to re- installation, contact the manufacturer strain your child and on its installation.
Page 54 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
Page 55: Choosing A Child Seat Mounting
CHILD SAFETY: choosing a child seat mounting (1/2) There are two ways of attaching child Attachment using the ISOFIX Before using an ISOFIX seats: via the seat belt or using the system child seat that you pur- ISOFIX system. Authorised child seats ISOFIX are chased for another vehicle, standardised in accordance with cur- check that its installation is...
Page 56 CHILD SAFETY: choosing a child seat mounting (2/2) The rings are located on the rear seat-  backs and indicated by the symbol In all cases, attach the strap hook to the corresponding ring 3 and 4 and place the seat in the desired position. Pull the belt so that the back of the child seat comes into contact with the back of the vehicle seat.
Page 57: Fitting A Child Seat, General Information
CHILD SAFETY: fitting a child seat, general information (1/2) Some seats are not suitable for fitting The types of child seats indicated may After installing the child seat, when this child seats. The diagram on the follow- not be available. Before using a differ- is possible, you can move the vehi- ing page shows you how to attach a ent child seat, check with the manufac-...
Page 58 CHILD SAFETY: fitting a child seat, general information (2/2) In the rear side seat In all situations, remove the rear head- rests. ➥ 3.34 If necessay, position the A carrycot can be installed across the rear seat as far as back possible. This vehicle and will take up at least two must be done before fitting the child seats.
Page 59 CHILD SEATS: attachment by seat belt (1/3) ³ Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. ² Seat not suitable for fitting child seats. ¬ Seat which allows a child seat with “Universal”...
Page 60 CHILD SEATS: attachment by seat belt (2/3) The table below summarises the information already shown on the diagram on the previous page, to ensure the applica- ble regulations are respected. Front passenger seat (1) (2) Rear centre Type of child seat Weight of the child Rear side seats Without airbag...
Page 61 CHILD SEATS: attachment by seat belt (3/3) X = Seat not suitable for fitting child seats of this type. U = Seat allowing a child seat with “Universal” approval to be attached using the seat belt; check that it can be fitted. B2 = Seat allowing a child seat with “B2”...
Page 62 CHILD SEATS: attachment using the ISOFIX system (1/3) The table below summarises the information already shown in the diagram on the following pages, to ensure the appli- cable regulations are respected. Front passenger seat Weight of Seat size Rear side Rear Type of child seat Without airbag...
Page 63 CHILD SEATS: attachment using the ISOFIX system (2/3) X = Seat not suitable for fitting child seats of this type. IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be at- tached using the ISOFIX system; check that it can be fitted. i-U = Suitable for “universal”...
Page 64 CHILD SEATS: attachment using the ISOFIX system (3/3) Child seat fitted using the ISOFIX mounting ü Seat which allows a ISOFIX child seat to be attached. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be attached.
Page 65 CHILD SAFETY: deactivating, activating the front passenger air bag (1/3) The passenger airbag must be deactivated or activated with the ignition off and vehicle stopped. If it is interfered with when the ve- hicle is being driven, indicator lights å ©...
Page 66 CHILD SAFETY: deactivating, activating the front passenger air bag (2/3) The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER...
Page 67 CHILD SAFETY: deactivating, activating the front passenger air bag (3/3) Operating faults It is forbidden to fit a rear-facing child seat to the front passenger seat if the airbags activation/deactivation system is faulty. Allowing any other passenger to sit in that seat is not recommended.
Page 68: Driving Position
DRIVING POSITION: LEFT-HAND DRIVE (1/2) 12 13 17 17 1.54...
Page 69: Instrument Panel
– Headlight beam adjustment, 15 Passenger Airbag location. – Hill Descent Control on/off, 9 Engine start/stop button (vehicle – Tailgate opening or Lane depar- with RENAULT card). 16 Glovebox. ture warning on/off (depeding on the vehicle), 10 Multifunction screen. 17 Accessories socket or cigarette –...
Page 70 DRIVING POSITION: RIGHT-HAND DRIVE (1/2) 11 12 17 21 1.56...
Page 71 13 Controls for on-board computer in- 20 Engine start/stop button (vehicle – activation/deactivation of the Stop formation read-out and vehicle set- with RENAULT card). tings customisation menu. and Start function. 21 Accessories socket or cigarette 5 Heating or air conditioning con- 14 Steering column stalk for wind- lighter and Multimedia sockets.
Page 72 WARNING LIGHTS (1/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Left-hand direction indicator In some cases, the appearance of a warning light is accompanied by a mes- tell-tale 5sage. Right-hand direction indica- š Side light warning light tor tell-tale Low fuel level warning light á...
Page 73 WARNING LIGHTS (2/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. À Brake circuit fault warning Oil pressure warning light light It lights up when the ignition or It lights up when the ignition or the the engine is switched on and goes off engine is switched on and goes off after after a few seconds.
Page 74 WARNING LIGHTS (3/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Ä Toxic Fume Filter System Anti-lock braking warning Warning Light light On vehicles which are equipped with it, It lights up when the ignition or the this light comes on when the engine is engine is switched on and goes off after started and, depending on the vehicle,...
Page 75 WARNING LIGHTS (4/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. å Rear seat belt reminder (depending Air bag warning light on vehicle) This warning light will be dis- ß played on the instrument panel when Warning light comes on, accom- the ignition is switched on or the engine...
Page 76 WARNING LIGHTS (5/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.  Ð Ï  Speed limiter, Assisted parking brake fault cruise control light and adaptive cruise control indicator ➥ 2.19 lights ➥ 2.67, ➥ 2.70, ➥ 2.74 ...
Page 77 WARNING LIGHTS (6/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. ß Driver’s seat belt reminder and, depending on the vehi- cle, front passenger seat belt re- minder This lights up when the ignition is switched on, then, if the driver's or front passenger's (if this seat is occupied) seat belt is not fastened and the vehicle...
Page 78 DISPLAYS AND INDICATORS (1/2) Instrument panel A Rev counter 4 Instrument panel in miles (option to switch to km/h) (graduations x 1000) Depending on the vehicle, you can cus- Vehicles not fitted with a navigation tomise your instrument panel with the system content and colours of your choice.
Page 79: Trip Computer And Warning System
DISPLAYS AND INDICATORS (2/2) Coolant temperature Engine oil level low warning Vehicles fitted with a navigation system indicator 7 When the engine is started, the instru- On the multifunction screen, select ment panel display A alerts you when In normal use, indicator 7 should be “System”...
Page 80 TRIP COMPUTER: general information (1/2) Display selection keys 2 Scroll through the following information by repeated short presses on the con- trol 2 (the display depends on the vehi- cle equipment and country): a) total mileage and trip mileage re- corder;...
Page 81 TRIP COMPUTER: general information (2/2) Interpreting some of the values displayed after resetting The values showing average fuel con- sumption and average speed will become more stable and reliable the further you have travelled since the last time the Reset button was pressed. The average fuel consumption may de- crease when: –...
Page 82 TRIP COMPUTER: trip settings (1/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101778 km 112.4 km a) Total mileage and trip mileage recorder. Average b) Journey parameters: Average fuel consumption since the last reset.
Page 83 TRIP COMPUTER: trip settings (2/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Range Estimated range with remaining fuel. The value is displayed after driving 400 metres. 541 km Distance Distance travelled since last reset.
Page 84 TRIP COMPUTER: trip settings (3/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with mileage- before-service message c) Mileage before service or oil change. Mileage before service Service in With the ignition switched on, the engine not running and Service Intervals...
Page 85 TRIP COMPUTER: trip settings (4/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with distance before next service message (cntd.) c) Mileage before service or oil change. Mileage before service Oil change in With the ignition switched on and the engine not running,...
Page 86 TRIP COMPUTER: trip settings (5/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected d) Reset the tyre pressure. Tyre pressure ➥ 2.29 e) Trip log. Successive display: No message –...
Page 87 TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpreting the display selected «...
Page 88 TRIP COMPUTER AND WARNING SYSTEM: operating fault messages © These appear with the warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.
Page 89 TRIP COMPUTER AND WARNING SYSTEM: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traf- fic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Some examples of warning messages are given below.
Page 90: Vehicle Settings Customisation Menu
VEHICLE SETTINGS CUSTOMISATION MENU (1/2) Adjusting the settings (depending on the vehicle) Select the function to modify: a) unlocking the driver’s door only; b) automatic locking of the doors while driving; c) hands-free function; d) indicator audio volume; e) internal welcome sound; f) external welcome;...
Page 91 VEHICLE SETTINGS CUSTOMISATION MENU (2/2) Adjusting the settings (depending on the vehicle) function activated Browse using the control 4 to select the < function to adjust: function deactivated a) Language; Once a line has been selected, press the switch 3 OK to adjust the function. b) Vehicle speed unit;...
Page 92: Steering Wheel, Power-Assisted Steering
STEERING WHEEL, POWER-ASSISTED STEERING (1/2) Power-assisted steering Variable power-assisted steering The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) while the force needed to steer increases progressively as the speed rises (for...
Page 93 STEERING WHEEL, POWER-ASSISTED STEERING (2/2) Activating the function With the ignition on, press the switch 3 , the warning light integrated in the switch lights up. Deactivating the function - Automatic: The function switches off automati- cally after the regulation phase of ap- proximately 30 minutes.
Page 94 CLOCK AND EXTERIOR TEMPERATURE External temperature indicator Special note: When the exterior temperature is - 3 °C to + 3 °C, the °C characters flash (sig- nalling a risk of ice on the road). Display 1 Vehicles fitted with a touchscreen multimedia screen, navigation aid systems, etc.
Page 95: Rear View Mirrors
Automatic mode is then deactivated. To - when the ignition is next switched on reactivate it, position switch 3 to B. (function deactivated); - upon detecting the RENAULT card or upon unlocking the vehicle (func- tion activated). Door mirrors Adjustment...
Page 96 REAR VIEW MIRRORS (2/3) Position memory Recalling the memorised position - Adjust the door mirrors (see previous paragraphs); From the multifunction screen, select menu “Vehicle”, “Seats”, “Settings” then - from the multifunction screen, select “Position” and select “Recall”. menu “Vehicle”, “Seats”, “Settings” then “Position”...
Page 97 REAR VIEW MIRRORS (3/3) Rear view mirror without lever 4 The rear-view mirror darkens automati- cally at night if you are being followed by a vehicle with its lights on. Interior rear view mirror Its position can be adjusted. Rear-view mirror with lever 4 For night driving, to avoid being dazzled by the headlights of the car behind you, flip the small lever 4 located behind the...
Page 98: Exterior Lighting And Signals
EXTERIOR LIGHTING AND SIGNALS (1/5) Dipped beam headlights Manual operation Turn ring 3 until the symbol is opposite mark 2. This indicator light on the in- strument panel comes on. Automatic operation Turn ring 3 until the AUTO symbol is op- posite mark 2: with the engine running, the dipped beam headlights switch on or off automatically depending on the...
Page 99 EXTERIOR LIGHTING AND SIGNALS (2/5)  Automatic main beam Activation Turn ring 3 until the AUTO symbol is op- headlights posite mark 2. Depending on the vehicle, this system Push stalk 1 to activate the main beam  switches the main beam headlights on headlights.
Page 100 EXTERIOR LIGHTING AND SIGNALS (3/5) Daytime running lights Switching off the lights function There are two possibilities: The daytime running lights come on – manually, move ring 3 to position 0; automatically with no action on stalk 1 – automatically, the lights will go out when the engine is started, and they go when the engine is switched off, the off once the engine is switched off.
Page 101 With the engine and lights switched ing the RENAULT card or when the ve- off and the ring 3 in position 0 or hicle is unlocked. AUTO, pull the stalk 1 towards you: the...
Page 102 EXTERIOR LIGHTING AND SIGNALS (5/5) Rear fog lights Switching off the lights Turn centre ring 5 on the stalk Turn the ring 5 again until the mark 4 until the symbol faces mark 4, then re- is opposite the symbol for the fog light lease it.
Page 103: Audible And Visual Signals
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. One-touch mode Briefly shift the stalk 1 upwards or downwards, not exceeding the point of resistance, then release it: the stalk will return to its original position and the direction indicator light concerned will flash three times.
Page 104: Headlight Beam Adjustment
HEADLIGHT BEAM ADJUSTMENT (1/2) For manual settings Examples of positions for adjusting control A according to the load Driver alone or with front passenger or with one front passenger and two or three rear passengers Do not use On vehicles fitted with this function, control A allows you to adjust the height Driver with a full car of passengers, luggage or (load) of the beams according to the load.
Page 105 HEADLIGHT BEAM ADJUSTMENT (2/2) When driving on the left in a left- hand drive vehicle (or vice versa), you must adjust your lights tempo- rarily during your stay. Temporary adjustment for vehicles fitted with halogen headlights Open the bonnet and identify the mark- ing B next to one of the front headlight projectors.
Page 106 WINDSCREEN WASH, WIPE (1/6) Efficiency of a wiper blade Check the condition of the wiper blades. How long they last depends on you: – it must remain clean: clean the blades and the screen regularly with soapy water; – do not use it when the screen is dry;...
Page 107 WINDSCREEN WASH, WIPE (2/6) When activating automatic wiping or when increasing sensitivity, one sweep of the blades is performed. Note: – the rain sensor is only intended as a driving aid. In the event of reduced visibility, the driver should manually activate the wipers.
Page 108 WINDSCREEN WASH, WIPE (3/6) Operating fault Special note When driving the vehicle, the wiping In the event of a malfunction of the au- speed slows down whenever the ve- tomatic wiping, the wiper is set to inter- hicle stops. For example, fast wiping mittent wiping.
Page 109 WINDSCREEN WASH, WIPE (4/6) Specific front wiper position Note: (service position) Once the wipers have been switched off, at least 1 minute after locking the This position enables the blades to be vehicle, it is possible to manually move lifted to remove them from the wind- the blades.
Page 110 WINDSCREEN WASH, WIPE (5/6) Note: In temperatures below zero, the washer liquid risks freezing to the windscreen, thereby reducing visibility. Heat the windscreen using the demister control before cleaning. Windscreen washer With the ignition on, pull stalk 1 then release. A brief pull will trigger a single sweep of the wipers, in addition to the wind- screen washer.
Page 111 WINDSCREEN WASH, WIPE (6/6) Note: To ensure the headlight washers op- erate correctly in winter, remove snow from the jet trims and de-ice the jet trims using an aerosol de-icer. You are recommended to regularly remove dirt encrusted on the headlight glass.
Page 112 REAR SCREEN WASH, WIPE (1/2) To stop the operation, pivot ring 3 again. Note: When washing using a roller type car wash, return the ring 3 on the stalk 1 Efficiency of a wiper blade to the stop position to deactivate auto- Check the condition of the wiper matic wiping.
Page 113 REAR SCREEN WASH, WIPE (2/2) Activation/deactivation of the rear In the event of obstacles present on the screen wiper rear window (dirt, snow, etc.), the wiper (depending on the vehicle) will try to sweep away all the obstacles. If an obstacle prevents the blade from Engaging reverse gear triggers inter- moving, it can be stopped.
Page 114: Fuel Tank (Filling With Fuel)
FUEL TANK (1/3) Fuel grade Use a high-grade fuel that complies with the legislation in force in each country and which must comply with the specifications given on the label on the cover A. ➥ 6.6 Petrol version It is essential to use unleaded petrol. The octane rating (RON) must comply with the information given on the label on the cover A.
Page 115 FUEL TANK (2/3) Filling with fuel Do not mix even small With the ignition off, insert the nozzle amounts of petrol (un- and insert it fully before turning it on to leaded or E85) with diesel. fill the fuel tank (risk of splashing). Do not use ethanol-based Keep the nozzle in this position through- fuel if your vehicle is not compatible...
Page 116 Vehicles with RENAULT card Persistent smell of With the card RENAULT in the pas- fuel senger compartment, press the start If you notice a persistent button 5 without pressing any of the smell of fuel you should: pedals.
Page 117: Reagent Tank
REAGENT TANK (1/4) Please ensure that you comply with the legislation of your country. It is important to remember that failure to respect regulations in force could lead to legal action being taken against Vehicle fitted with the Stop and the vehicle owner.
Page 118 REAGENT TANK (2/4) Precautions for use In extreme cold weather conditions In frosty weather conditions, the rea- The tank can be filled at the pump. In gent tank should be refilled when the other cases, it is essential to read the ...
Page 119 REAGENT TANK (3/4) Maintenance/Range The information displayed on the instrument panel may be accompanied by a beep. Indicator lights Message What to do? – “AdBlue Level Correct” – When the message is displayed when the ignition is switched on, you have less than 1,488 miles (2,400 km) range. –...
Page 120 REAGENT TANK (4/4) System fault When the indicator lights light up, this may be accompanied by a beep. Indicator lights Message Readings “Check anti-pollution system” Indicates a fault in the system. Contact your approved  “Adblue quality to check” © dealer as soon as possible.
Page 121 Starting, stopping the engine: vehicle with RENAULT card ....... .
Page 122 RUNNING IN Petrol version Diesel version Note: for a new vehicle in the running in phase: the coolant fluid level may For the first 600 miles (1,000 km), do For the first 1,000 miles (1,500 km), be higher than the “MAXI” mark on not exceed 78 mph (130 km/h) in the do not exceed 80 mph (130 km/h) in the tank, then drop between the level...
Page 123 IGNITION SWITCH: vehicle with key Ignition position 2. The ignition is switched on: Start position 3. If the engine fails to start at the first attempt, the key must be turned back before the starter can be activated again. Release the key as soon as the engine starts.
Page 124: Starting, Stopping The Engine: Vehicle With Key/Remote Control Unit
STARTING, STOPPING THE ENGINE: vehicle with key É Stopping the engine Diesel versions With the engine idling, turn the key to – Turn the ignition key to the the “Stop” position 0. “Ignition on” position 2, and hold this position until the engine pre- heating light goes off;...
Page 125: Starting, Stopping The Engine: Vehicle With Renault Card
STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (1/5) “Hands-free” starting with the tailgate open In this case, the RENAULT card should not be located in the boot, to avoid any risk of loss. Driver’s responsibility when parking or stopping...
Page 126 STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (2/5) Depress the brake or clutch pedal, then place the RENAULT 3 card (logo side) in contact with the start button 2 for around 2 seconds. Press the 2 button to start the vehicle. The message goes out.
Page 127 STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (3/5) If the RENAULT card is no longer in the passenger compartment or if the card When you leave your vehi- battery is low when you try to switch cle, especially if you have the engine off, the message “No key-...
Page 128 STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (4/5) Depending on the vehicle, the configu- ration and the programming are done using the multimedia display 6. Refer to the multimedia instructions for your vehicle. The range for the remote engine start-...
Page 129 STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (5/5) The remote engine start-up operates: Do not use the engine – the lever is in neutral for vehicles remote start-up function or with a manual or sequential gearbox; Special feature of vehicles its programming when: –...
Page 130: Stop And Start Function
STOP AND START FUNCTION (1/4) This system enables a reduced fuel For all vehicles: consumption and lower greenhouse gas Depending on the vehicle, warning light emissions.  on the instrument panel appears The system is activated automatically when the engine is on standby. when the vehicle is started.
Page 131 STOP AND START FUNCTION (2/4) Preventing the standby of the Conditions for coming out of Special note: depending on the vehicle, if you switch off the ignition when the engine the engine standby engine is on standby, the warning light Ä...
Page 132 Special cases for vehicles – parking distance control is in opera- tion; standby of the engine with a RENAULT card – for vehicles with automatic gear- Certain conditions prevent the system With the engine on standby (traffic jam, boxes, the gradient is steeper than from using the engine standby function, traffic lights, etc.), if the driver unfas-...
Page 133 STOP AND START FUNCTION (4/4) Special feature of the automatic Pressing again will reactivate the engine re-start system. The message “Stop & Start ac- tivated” will appear on the instrument Under certain conditions, the engine can panel and the integrated warning light 2 restart on its own in order to guarantee on switch 1 will go out.
Page 134: Special Features Of Petrol Versions
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...
Page 135: Special Features Of Diesel Versions
SPECIAL FEATURES OF DIESEL VERSIONS (1/2) Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection equipment which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.
Page 136 SPECIAL FEATURES OF DIESEL VERSIONS (2/2) Particle filter Note: the warning light may reappear If the filter becomes saturated, the © if the driving conditions are not fully warning light and, depending The particle filter is used to treat of ex- ...
Page 137: Gear Lever
GEAR LEVER Selecting reverse gear The ring 2 has to be lifted up to the gear lever knob to select reverse gear. The reversing lights will come on as soon as reverse gear is selected with the ignition on. Gear lever Vehicles with manual gearbox: refer to the grid on the gear lever knob 1.
Page 138 PARKING BRAKE Parking brake To release: Depress the parking brake 1 firmly. The red warning light on the instrument panel will come on if you are driving with an incorrectly released parking brake. To apply: Depress the parking brake 1 firmly. Make sure that the park- Check that the vehicle is immobilised.
Page 139 ELECTRONIC PARKING BRAKE (1/3) Assisted operation Note: To indicate that the electronic parking The assisted parking brake immobi- brake is released, a beep sounds and lises the vehicle when stopping the the message “Apply parking brake” ap- engine (and not when the engine is pears on the instrument panel: on standby for vehicles fitted with the Stop and Start function).
Page 140 ELECTRONIC PARKING BRAKE (2/3) Brief stop Special cases To manually activate the electronic par- To park on a slope or while towing a king brake, (when stopping at a red trailer, for example, pull switch 1 for a light, or stopping when the engine is few seconds to gain the maximum bra- running, etc.): pull and release switch 1.
Page 141 ELECTRONIC PARKING BRAKE (3/3) Versions with an automatic Operating faults If the message “WARNING: gearbox © Electric System” or “Electric – If there is a fault, the warning failure DANGER” or “Check light illuminates on the instrument For safety reasons, automatic release battery”...
Page 142: Eco Driving
DRIVING ADVICE, ECO-DRIVING (1/5) Fuel consumption is accredited in ac- cordance with a standard regulatory method. Identical for all manufactu- rers, this enables vehicles to be com- pared with one another. Consumption in real time depends on vehicle usage conditions, the equipment fitted and the user’s driving style.
Page 143 DRIVING ADVICE, ECO-DRIVING (2/5) This indicates: – average fuel consumption; – number of miles/kilometres travelled; – number of miles/kilometres saved. This corresponds to driving without fuel consumption (deceleration and/ or foot off the accelerator pedal). An overall rating from 0 to 100 is dis- played to let you assess your eco dri- ving performance.
Page 144 DRIVING ADVICE, ECO-DRIVING ( 3/5) ECO mode ECO mode is a function which opti- mises fuel consumption. It acts upon certain power consuming systems in the vehicle (heating, air conditioning, power-assisted steeting, etc.) and on certain driving actions (acceleration, gear changing, cruise control, decele- ration, etc.).
Page 145 DRIVING ADVICE, ECO-DRIVING (4/5) – High speeds significantly affect the – Do not try to maintain the same Heating level vehicle’s fuel consumption. speed up a hill, accelerate no more It is normal to notice an increas in the than you would on flat ground. Keep Examples (at a steady speed): vehicle’s fuel consumption when using your foot in the same position on the...
Page 146 DRIVING ADVICE, ECO-DRIVING (5/5) – On vehicles equipped with nonau- tomatic air conditioning, switch off the air conditioning when it is not re- quired. Advice for reducing consumption and therefore helping to preserve the environment: If the vehicle has been parked in the sun, open the doors for a few mo- ments to let the hot air escape before starting the engine.
Page 147: Maintenance And Antipollution Advice
MAINTENANCE AND ANTIPOLLUTION ADVICE Maintenance Exhaust gas monitoring Your vehicle complies with criteria for recycling and recovering vehicles at the system It is important to remember that fail- end of their service life, which will come ure to respect anti-pollution regulations The exhaust gas monitoring system will into force in 2015.
Page 148: Environment
This commitment is illustrated by the lation. less fuel (eg. 140 g/km, equivalent to Renault eco² signature. 5.3 l/100 km for a diesel vehicle). Recycling Our vehicles are also equipped with a Manufacture...
Page 149 TYRE PRESSURE MONITORING SYSTEM (1/3) Resetting the standard level Resetting procedure for the tyre pressures With the ignition on, vehicle stopped: This should be done: – repeatedly and briefly press control 2 to select the tyre pressure display – when the standard tyre pressure and the “Tyre pressure”...
Page 150 TYRE PRESSURE MONITORING SYSTEM (2/3) « Puncture » A wheel B is shown in red, the warn-  ing light 4 comes on, the mes- sage “Puncture” appears and there is a beep.This message appears along with ® warning light. They indicate that the affected wheel is punctured or severely underinflated.
Page 151 Because the valves are specially de- wheels have been fitted with sensors ➥ 5.10 signed, only use equipment approved not recognised by Renault. by the approved network. ➥ 5.4 Contact an approved Dealer to fit new Consult an approved dealer...
Page 152 DRIVING CORRECTION DEVICES AND AIDS (1/5) ABS (anti-lock braking Depending on the vehicle, they will con- sist of: system) In an emergency, apply firm and – ABS (anti-lock braking system) ; Under heavy braking, the ABS prevents continuous pressure to the brake the wheels from locking, allowing the –...
Page 153 DRIVING CORRECTION DEVICES AND AIDS (2/5) Electronic stability control Operating faults: Understeer control ESC with understeer control © This system optimises the action of the – lit up on the in- and traction control ESC in the case of pronounced under- strument panel alongside mes- steer (loss of front axle road holding).
Page 154 DRIVING CORRECTION DEVICES AND AIDS (3/5) Operating faults The traction control system offers ad- ditional safety. It is recommended that When the system detects an operat- you do not drive with the function di- ing fault the message “Check ESC” and sabled.
Page 155 DRIVING CORRECTION DEVICES AND AIDS (4/5) Hill start assistance Depending on the gradient of the in- cline, this system assists the driver when starting on a hill. It prevents the vehicle from rolling backwards by au- tomatically applying the brakes when the driver lifts his/her foot off the brake pedal to depress the accelerator pedal.
Page 156 DRIVING CORRECTION DEVICES AND AIDS (5/5) Activating/deactivating the system System warning message - Activation: press the button 2 in - Internal failure normal activation condition that is - Vehicle speed is over 19mph  (30km/h) below 19mph(30km/h). The indicator light on the instrument pane - Push the Accel pedal aggressively comes on.
Page 157: Transmission: 4-Wheel Drive (4Wd)
TRANSMISSION: 4-wheel drive (4WD) (1/4) Mode selector “2WD” mode Depending on the road conditions, turn- To activate this mode, turn the selec- ing the selector 1 enables the following tor 1 to the “2WD” position. The warn- ‘ modes to be selected: ing light on the instrument panel –...
Page 158 TRANSMISSION: 4-wheel drive (4WD) (2/4) “4WD Lock” mode Note: If the vehicle speed exceeds This problem may be resolved by approximately 24.8 mph (40 km/h) in changing the tyres. Always use four To activate this mode, turn selector 1 to “4WD Lock”...
Page 159 TRANSMISSION: 4-wheel drive (4WD) (3/4) Operating faults After stopping the engine, the system Electronic stability program and may take up to five minutes to cool traction control when driving off- If the system detects an operating fault, road down. it automatically switches to “2WD” If the system detects excessive wheel- When driving on soft ground (sand, mode.
Page 160 TRANSMISSION: 4-wheel drive (4WD) (4/4) All-wheel drive system – Irrespective of the mode selected, do not start the engine if one or more wheels are not in contact with the ground (eg. when the vehicle is on a jack or roller bench). –...
Page 161: Active Emergency Braking
ACTIVE EMERGENCY BRAKING (1/11) Active emergency braking The system has two types. Depending on the vehicle, one of the two systems is equipped in the vehicle. - System A - System B System A is composed of the radar System B is using the radar-camera sensor 1 and the front camera 2.
Page 162 ACTIVE EMERGENCY BRAKING (2/11) System A Operating principle Using the radar sensor, the system cal- culates the distance separating the ve- hicle from the one in front and alerts the driver if there is a risk of a front-end col- lision.
Page 163 ACTIVE EMERGENCY BRAKING (3/11) Operating faults Press the switch 7 OK again to activate or deactivate the function: When the system detects an operating  function activated fault, the warning light lights up < on the instrument panel, with the mes- function deactivated ...
Page 164 ACTIVE EMERGENCY BRAKING (4/11) Active emergency braking This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The triggering of this function may be delayed or prevented when the system detects clear signs of control of the vehicle by the driver (action on the steer- ing wheel, pedals etc.).
Page 165 ACTIVE EMERGENCY BRAKING (5/11) Limitation of the system operation – The system will only respond to vehicles which are moving or which have been sensed as moving. – The radar area should be kept clean and free of any modifications in order to ensure the proper operation of the system.
Page 166 ACTIVE EMERGENCY BRAKING (6/11) System B Operating principle Using information from the radar-cam- era, the system calculates the distance which separates it from the vehicle in front and the surrounding pedestrians. It notifies the driver if there is a risk of head-on collision.
Page 167 ACTIVE EMERGENCY BRAKING (7/11) System B (continued) Special features When the vehicle speed: Detection of vehicles – is less than 27.9 mph (45 km/h) ap- proximately, the warning and brak- Operation ing are activated at the same time; When driving (speed between about –...
Page 168 ACTIVE EMERGENCY BRAKING (8/11) Press the switch 8 OK again to activate or deactivate the function: function activated < function deactivated  The warning light is displayed on the instrument panel when the system is deactivated. This system is reacti- vated each time the ignition is switched System B (continued) For vehicle not fitted with a...
Page 169 ACTIVE EMERGENCY BRAKING (9/11) Temporarily not available Operating faults System B (continued) When the system detects a tempo- When the system detects an operating   Conditions for non-activation rary unavailability, the warning fault, the warning light lights up of the system light lights up on the instrument panel on the instrument panel, with the mes- The system cannot be activated:...
Page 170 ACTIVE EMERGENCY BRAKING (10/11) Active emergency braking This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The triggering of this function may be delayed or prevented when the system detects clear signs of control of the vehicle by the driver (action on the steer- ing wheel, pedals etc.).
Page 171 ACTIVE EMERGENCY BRAKING (11/11) Limitation of the system operation – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. – The radar-camera area on the windscreen should be kept clean and free of any modifications in order to ensure the proper operation of the system.
Page 172: Lane Departure Warning
LANE DEPARTURE WARNING (1/3) This system notifies the driver when they accidentally cross a continuous or broken line. This function uses a camera attached to the windscreen, behind the rear-view mirror. This function is a driving aid in the event of the accidental crossing of a continuous or broken line in the road.
Page 173 LANE DEPARTURE WARNING (2/3) Activation/deactivation Vehicles not fitted with a navigation system – the line indicators 4 are coloured Vehicles fitted with a navigation Press the switch 3. green or, depending on the vehicle, system a vibration of the steering wheel; From the multifunction screen 2: select Operation The function alerts the driver:...
Page 174 LANE DEPARTURE WARNING (3/3) Adjustment – repeatedly press control 6 up or down until you reach the “Lane de- Vehicles fitted with a navigation parture warning settings” menu, then system press the switch 5 OK. From the multifunction screen 2, select –...
Page 175: Fatigue Detection Warning
FATIGUE DETECTION WARNING (1/2) The fatigue detection warning is a func- tion which is useful on monotonous roads (motorways, high-speed roads etc.). It analysis driver behaviour and takes account of events to inform you of any risk of fatigue such as: –...
Page 176 FATIGUE DETECTION WARNING (2/2) – repeatedly press control 5 up or Note: down until you reach the “Fatigue de- – if the warning is not deleted by press- tection warn.” menu, then press the ing switch 4 OK, the beep repeats; switch 4 OK.
Page 177: Blind Spot Warning
BLIND SPOT WARNING (1/4) This function is an addi- tional aid which indicates other vehicles in the blind spot area. Special feature This system alerts the driver to other It can never in any case be a subs- vehicles in the detection zone A. Make sure that the sensors are not ob- titute for care nor for the driver’s scured (by dirt, mud, snow, etc.).
Page 178 BLIND SPOT WARNING (2/4) – repeatedly press control 5 up or down until you reach the “Blind spot alert” menu, then press the switch 4 – Press the switch 4 OK again to acti- vate or deactivate the function. Activation/deactivation Vehicles not fitted with a navigation system Vehicles fitted with a navigation...
Page 179 BLIND SPOT WARNING (3/4) Display B The function is activated and has not detected any vehicles. Display C Initial warning: the indicator light 6 shows that a vehicle has been detected in the blind spot. Display D When the direction indicator is activa- ted, the indicator light 6 flashes when a vehicle is detected in the blind spot on the side towards which you are about to...
Page 180 BLIND SPOT WARNING (4/4) Operating faults If the system detects a fault, the mes- sage “Check blind spot alert” is dis- played on the instrument panel. Consult an authorised dealer. Note: When the engine is started, the indicator light 6 (display B) flashes three times.
Page 181: Safe Distance Alert
SAFE DISTANCE ALERT (1/3) Activating/deactivating the Using the information from the radar 1, this function informs the driver of the function time interval between him and the vehi- From the multifunction screen 2, select cle in front so that a safe stopping dis- menu “Vehicle”, “Driving assistance”, tance between the 2 vehicles can be “Distance warning”...
Page 182 SAFE DISTANCE ALERT (2/3) – C (orange): the time interval falls between around 1 and 2 seconds (in- sufficient distance between the two This function is essential if adaptive vehicles); cruise control is activated. – D (red): the time interval is less than or equal to around one second (very insufficient distance between the two vehicles).
Page 183 SAFE DISTANCE ALERT (3/3) This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. System servicing/repairs –...
Page 184 OVERSPEED ALERT (1/3) Operating principle Vehicle fitted with a navigation system The system detects speed limit signs - If the vehicle is travelling in a coun- on the side of the road and displays the try where the speed units differ from speed limit.
Page 185 OVERSPEED ALERT (2/3) – repeatedly press the control 6 up or down until you reach the “Driving as- sistance” menu. Press the switch 5 – repeatedly press the control 6 up or down until you reach the Speed alert menu, then press the switch 5 OK. –...
Page 186 OVERSPEED ALERT (3/3) Operating fault This function is an additional driving aid. This function is not under any The system cannot detect the speed circumstances intended to replace the due care and attention of the limit if: driver, who should at all times be in control of the vehicle. –...
Page 187: Speed Limiter
SPEED LIMITER (1/3) Switching on  Press switch 1 on side . The indica-  tor light comes on, lit orange, and the message “Speed limiter” appears on the instrument panel, accompanied by dashes to indicate that the speed limiter function is activated and waiting to store a limited speed.
Page 188 SPEED LIMITER (2/3) Varying the limit speed Exceeding the limit speed The speed limiter can be changed by It is possible to exceed the limit speed repeatedly pressing the switch 2: at any time. To do this: press the accel- erator pedal firmly and fully (beyond –...
Page 189 SPEED LIMITER (3/3) Recalling the limit speed If a speed has been saved, it can be re- called by pressing switch 3 (R). Putting the function on Switching off the function standby The speed limiter function is deacti- vated if you press switch 1: in this case The speed limiter function is sus- a speed is no longer stored.
Page 190: Cruise Control
CRUISE CONTROL (1/4) This function is an addi- tional driving aid. It can under no circum- stances replace the driver’s Controls The cruise control function helps you to responsibility to respect speed limits maintain your driving speed at a speed 1 Main “On/Off”...
Page 191 CRUISE CONTROL (2/4) Activating cruise control At a steady speed (above approx. 20 mph (30 km/h)), press the switch 2 on side a (+): the function is activated and the current speed is saved. The cruising speed replaces the dashes and cruise control is confirmed by the appearance of the message “Check cruise control”...
Page 192 CRUISE CONTROL (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While overtaking, the cruis- ing speed flashes red on the instrument panel. Then, release the accelerator: after a few seconds, the vehicle will automati- cally return to its set cruising speed.
Page 193 CRUISE CONTROL (4/4) Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road con- ditions are suitable (traffic, road sur- face, weather conditions, etc.). Press switch 3 (R) if the vehicle speed is above 20 mph (30 km/h).
Page 194: Adaptive Cruise Control
ADAPTIVE CRUISE CONTROL (1/8) The adaptive cruise control is a func- tion which gives you the option, when traffic conditions permit (large free-flow- ing road or motorway), of maintaining a chosen speed, known as the cruising speed, while keeping a safe distance from the vehicle in front in the same lane.
Page 195 ADAPTIVE CRUISE CONTROL (2/8) Controls Switching on The cruising speed replaces the dashes and cruise control is confirmed by the 5 Main “On/Off” switch. Press switch 5 on the side showing  appearance of the message “Adaptive Warning light  comes on, lit green, 2 Controls for: cruise ctrl”...
Page 196 ADAPTIVE CRUISE CONTROL (3/8) Driving Varying the following distance Once a cruising speed is memorised and the cruise control function is active, You can vary the following distance you may lift your foot off the accelera- from the vehicle in front at any time by tor pedal.
Page 197 ADAPTIVE CRUISE CONTROL (4/8) Putting the function on Returning to the cruising speed standby If a speed is stored, it can be recalled, once you are sure that the road con- The function is set to standby if: ditions are suitable (traffic, road sur- –...
Page 198 ADAPTIVE CRUISE CONTROL (5/8) Under certain conditions (coming up behind a vehicle moving more slowly, rapid change of lane of vehicles in front etc.), the system may not have time to respond and may emit a beep along- side the alert A when the situation re- quires the driver’s attention, or the alert B when the situation requires im- mediate action from the driver.
Page 199 ADAPTIVE CRUISE CONTROL (6/8) Operating faults When the system detects an operating fault the message “Check cruise con- trol” appears on the instrument panel. There are two possibilities: – the system is temporarily disrupted (for example: radar obscured by dirt, mud, snow etc.).
Page 200 ADAPTIVE CRUISE CONTROL (7/8) This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The driver should always adapt their speed to the traffic conditions, regardless of the system indications.
Page 201 ADAPTIVE CRUISE CONTROL (8/8) Limitation of the system operation – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. – The radar-camera should be kept clean and free of any modifications in order to ensure the proper operation of the system.
Page 202 PARKING DISTANCE CONTROL (1/7) Operating principle Ultrasonic sensors in the rear bumper measure the distance between the ve- hicle and an obstacle. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 20 to 30 centimetres from the obstacle.
Page 203 PARKING DISTANCE CONTROL (2/7) Operation Note: the display 2 shows the vehicle surroundings and emits beeps. Most objects located less near the It is necessary to travel a few metres front, rear and sides of the vehicle are before the side detection is activated. detected.
Page 204 PARKING DISTANCE CONTROL (3/7) If a side obstacle is detected: – the beeps become faster and then sound continuously as the obstacle gets nearer. Green, orange and red zones will be displayed on the dis- play D; – if there is no risk of collision, no beep will sound when approaching the ob- stacle.
Page 205 PARKING DISTANCE CONTROL (4/7) System sound Enables the system sound to be se- lected from a choice of 3. Deactivating the system sound Activate or deactivate the parking dis- tance control sound. Note: If you deactivate the sound, you will no longer be notified with beeps when approaching an obstacle.
Page 206 PARKING DISTANCE CONTROL (5/7) Automatic deactivation of the Deactivating the parking parking distance control distance control manually The system deactivates: You must disable the function if: The function can be disrupted under – when the vehicle speed is above ap- –...
Page 207 PARKING DISTANCE CONTROL (6/7) System servicing/repairs – In the event of an impact, the alignment of the sensors may be altered and their operation may consequently be affected. Deactivate the function and consult an authorised dealer. – Any work in the area where the sensors are located (repairs, replacements, etc.) must be carried out by a qualified profes- sional.
Page 208 PARKING DISTANCE CONTROL (7/7) Limitation of the system operation – The area around the sensors must be kept clean and free of any modifications in order to ensure the proper operation of the system. – Small objects moving close to the vehicle (motorcycles, bicycles, pedestrians, etc.) may not be recognised by the system. –...
Page 209: Reversing Camera
REVERSING CAMERA (1/3) Operation Fixed gauge 3 4 moving guide line: The fixed clearance gauge comprises This is shown in blue on the multifunc- Moving into reverse gear, the camera 1 coloured markers A, B and C, indicat- tion screen 2. It indicates the vehicle located on the tailgate provides a view ing the distance behind the vehicle: trajectory according to the position of...
Page 210 REVERSING CAMERA (2/3) Operating faults When reverse gear is engaged, if the system detects an operating fault, a The screen shows a reverse mirror black screen is displayed temporarily image. on the multimedia screen 2. The frames are a representation This may be caused by a fault affecting projected onto flat ground;...
Page 211 REVERSING CAMERA (3/3) H J K Difference between the Reversing towards a steep downhill Reversing towards a protruding slope object estimated distance and actual distance The fixed guidelines 3 show the dis- Position H seems further than posi- tances as further than they actually are. tion J on the screen.
Page 212: Assisted Parking
ASSISTED PARKING (1/6) Look in all directions Select indicator Switching on Special features This function assists with parking ma- noeuvres. With the vehicle at a standstill or driving Ensure that the ultrasonic sensors indi- Take your hands off the steering wheel. at less than approximately 18.6 mph cated by arrows 3 are not obscured (by You only control the pedals and the...
Page 213 ASSISTED PARKING (2/6) Choice of manoeuvre Look in all directions Look in all directions Select indicator Reverse The system can perform four types of manoeuvres: – 4 parallel parking; – 5 perpendicular parking; – 6 angle parking; – 7 moving out of a parallel parking space.
Page 214 ASSISTED PARKING (3/6) Special note Look in all directions – Drive slowly and always be ready to Press and hold (icon) button to start use the brake; – The system can not detect parking spaces between objects except for vehicles such as a post, motorbike or obstacle;...
Page 215 ASSISTED PARKING (4/6) Special note Look in all directions Go forward or reverse – While exiting the parking space, the system is disrupted for safety when there is risk to impact with obstacles; – The system may not be operated when the space is small;...
Page 216 ASSISTED PARKING (5/6) Suspending the manoeuvre Special note Make sure: – you have released the steering wheel The manoeuvre is suspended in the fol- The system may be disrupted in the and; lowing circumstances: following circumstances. In this cases, – that all doors and the boot are closed, –...
Page 217 ASSISTED PARKING (6/6) This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. Make sure that the manoeuvre complies with the applicable traffic regulations at your location. –...
Page 218 AUTOMATIC TRANSMISSION (1/3) Driving in automatic mode Move lever 1 to position D. In most road conditions you will en- counter, you will not need to touch your lever again: the gears will change au- tomatically at the right time and at the most suitable engine speed because the automatic system takes into ac- count the vehicle load and road contour...
Page 219: Automatic Gearbox
AUTOMATIC TRANSMISSION (2/3) Special cases Special circumstances In certain driving conditions (for – If the bends and road surface do example, engine protection, operation not allow you to stay in automa- of the Electronic Stability Programme: tic mode (e.g. in the mountains), the automatic system may change gear we recommend that you change to automatically.
Page 220 AUTOMATIC TRANSMISSION (3/3) Parking the vehicle Maintenance period Refer to the maintenance document When the vehicle is stopped, move the for your vehicle or consult an Approved lever to position P while keeping your Dealer to check whether the automatic foot on the brake pedal: the gearbox is gearbox requires scheduled mainte- in neutral and the drive wheels are me-...
Page 221: Emergency Call
EMERGENCY CALL (1/2) If the vehicle is equipped, the emer- gency call function can be used to call the emergency services (without charge) automatically or manually in the event of an accident or illness, re- ducing the time it takes for the emer- gency services to arrive.
Page 222 EMERGENCY CALL (2/2) Automatic mode In the event of unintended operation, it is possible to cancel the call by press- When warning light 2 is on, this indi- ing switch 3 for 2 seconds before the cates that the automatic system is ac- call to the call centre is set up.
Page 223 Section 3: Your comfort Air vents............... Manual air conditioning, heating system .
Page 224 AIR VENTS, air outlets (1/2) 1 left-hand air vent 2 side window demister outlets 3 windscreen demisting vents 4 centre air vents 5 right-hand air vent 6 multifunction screen 7 footwell heater outlets for front pas- sengers 8 footwell heater outlets for rear pas- sengers 9 centre air vents for rear seats...
Page 225: Air Vents
AIR VENTS, air outlets (2/2) Centre air vents. Side air vents Air flow Air flow Move the control knob 11 or 12 (beyond Move the control knob 14 or 15 (beyond the resistance point). the resistance point). 11 left or 12 right: closed. 14 left or 15 right: closed.
Page 226 MANUAL AIR CONDITIONING (1/3) 10 11 12 The controls Indicators Switching air conditioning on or off 1 Adjusting the air temperature. The following indicators are displayed on the multimedia screen A: The air conditioning is switched on (in- 2 De-icing/demisting of the rear screen dicator light on) or off (indicator light off) and, depending on the vehicle, the 9 Air temperature.
Page 227 MANUAL AIR CONDITIONING (2/3) Distribution of air in the passenger compartment There are five air distribution options. Turn control 5 to choose the distribution option. The air distribution is displayed on the multimedia screen. õ The air flow is directed to the windscreen and the front side window demisting vents.
Page 228 MANUAL AIR CONDITIONING (3/3) Clear view function Press button 8 - the intrgrated indicator light comes on. This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-ic- ing functions must be activated.
Page 229: Automatic Climate Control
AUTOMATIC CLIMATE CONTROL: Control A (1/5) Automatic mode The automatic climate control system- guarantees comfort in the passen- ger compartment and good visibility (except in the event of extreme condi- tions), while optimising consumption. The system controls the ventilation speed, air distribution, air recirculation, and starting and stopping the air condi- tioning and air temperature.
Page 230 AUTOMATIC CLIMATE CONTROL: Control A (2/5) Varying the ventilation speed Temperature adjustment The displayed temperature values show a comfort level. There are two types of settings: In automatic mode, the system uses – uniform passenger compartment When starting the engine, increas- the most suitable amount of air to reach setting;...
Page 231 AUTOMATIC CLIMATE CONTROL: Control A (3/5) To exit this function, press either: – button 7; – again button 5; – on button 8, 9 or 10. Clear view function Press button 7 – the integrated indica- tor light comes on. This function quickly demists and de- Press button 4 to stop the heated rear ices the windscreen, the rear screen,...
Page 232 AUTOMATIC CLIMATE CONTROL: Control A (4/5) Using the ECO mode – If you press the button 20 when the air conditioning operates, ECO mode activate. – In the ECO mode, air condi- tioning speed and power is be weaken in order to optimize the fuel consumption.
Page 233 AUTOMATIC CLIMATE CONTROL: Control A (5/5) Air recirculation Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle; – air recirculation allows the exter- nal atmosphere to be cut off (when driving in polluted areas, etc.) and to cool the passenger compartment temperature more quickly.
Page 234 AUTOMATIC CLIMATE CONTROL: Controls B and C (1/5) Automatic mode 3 B 11 The automatic climate control system guarantees comfort in the passen ger compartment and good visibility (except in the event of extreme condi tions), whilst optimising consumption. The system controls the ventilation speed, air distribution, air recirculation, and starting and stopping the air condi tioning and air temperature.
Page 235 AUTOMATIC CLIMATE CONTROL: Controls B and C (2/5) Varying the ventilation speed Temperature adjustment The displayed temperature values show a comfort level. There are two types of settings: In automatic mode, the system uses When starting the engine, increas- the most suitable amount of air to reach –...
Page 236 AUTOMATIC CLIMATE CONTROL: Controls B and C (3/5) To exit this function, press either: – again button 1; – one of the buttons 3. Clear view function Press button 1 – the integrated indica- tor light comes on. This function quickly demists and de- Press button 5 to stop the heated rear ices the windscreen, the rear screen, screen operating, and the integrated in-...
Page 237 AUTOMATIC CLIMATE CONTROL: Controls B and C (4/5) Rear screen de-icing/ demisting Press button 5 – the integrated indica- tor light comes on. This function ena- bles rapid demisting or de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles).
Page 238 AUTOMATIC CLIMATE CONTROL: Controls B and C (5/5) Air recirculation Depending on the vehicle or country, Press button 8 or 9. Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle;...
Page 239 AIR CONDITIONING: information and operating instructions (1/3) Advice on use Fuel consumption Operating faults In some situations, (air conditioning You will normally notice an increase in As a general rule, contact your ap- off, air recirculation activated, ventila- fuel consumption (especially in town) proved dealer in the event of an oper- tion speed at zero or low, etc.) you may when the air conditioning is operating.
Page 240 AIR CONDITIONING: information and operating instructions (2/3) Ñ The refrigerant fluid circuit (of which Type of refrigerant fluid some components are hermetically sealed) may contain fluorinated green-  (XXX) Type of oil in the air house gases. conditioning circuit  Inflammable product Refrigerant fluid R-134a ...
Page 241 AIR CONDITIONING: information and operating instructions (3/3) Ñ Refrigerant fluid R-1234yf Type of refrigerant fluid Depending on the vehicle, you will find  (XXX) Type of oil in the air the following information on label B af- conditioning circuit fixed inside the engine compartment. ...
Page 242: Outside Air Quality And Deodorisation Functions
OUTSIDE AIR QUALITY AND DEODORISATION FUNCTION Take care Deodorization cycle Deodorisation function With the air conditioning switched on, from the screen A, select Menu, This reduces unpleasant odours in the Vehicle, Take care. passenger compartment. Outside air quality Deodorization cycle –...
Page 243: Electric Windows
Driver’s responsibility switch 6. Never leave your vehicle with the RENAULT card or key inside, and never leave a child, adult who is not self-sufficient or a pet, even for a short while. They may pose a risk to themselves or to others by starting the engine or activating equip- ment (such as the gear lever or electric windows).
Page 244 ELECTRIC WINDOWS (2/2) One-touch mode Operating faults Depending on the vehicle, this mode In case of a fault when closing a window, works in addition to the operation of the the system reverts to normal mode: electric windows described previously. pull the switch concerned up as often It is only fitted to the front windows.
Page 245: Electric Sunroof
ELECTRIC SUNROOF (1/2) To tilt the sunroof When the sunroof is closed, press switch 2 to tilt up the sunroof. It doesn’t need to be held. When the sunroof is tilt, press switch 2 to close the sunroof. It doesn’t need to Driver’s responsibility be held.
Page 246 ELECTRIC SUNROOF (2/2) It doesn’t need to be held. The sun- – check that the sunroof is properly roof will automatically open or close all closed before leaving your vehicle; the way. To stop the window, push the – clean the seal every three months switch once more while it is opening or using products recommended by our closing.
Page 247: Interior Lighting
INTERIOR LIGHTING (1/3) Interior lights switch 1 Front door lights 5 Note: For vehicles fitted with a naviga- tion system, you can use the multifunc- Press switch 1 to turn on/off map read- tion screen to deactivate/activate the ing light 3 and 4. When a door is open, Front footwell lights 6 courtesy lights which come on when door light 5 and foot light 6 are ON.
Page 248 INTERIOR LIGHTING (2/3) Map reading lights switch 7, 8 Front and rear door ambient Center console ambient light light Press switch 7, 8 to turn on/off left or- Center console ambient light 11 comes right map reading light independently. on when the door is opened. Front and rear door ambient light 10 comes on when the door is opened.
Page 249 INTERIOR LIGHTING (3/3) Glove box light Boot lights Glove box light 12 comes on when the Light 13 comes on when the boot is illumination is turned on. opened. 3.27...
Page 250 PASSENGER COMPARTMENT STORAGE, FITTINGS (1/5) Front door storage pockets 1 Front sun visor Sunvisor storage compartment 4 They can hold a 1.5-litre bottle. Lower sun visor 2. Sun visor can be slided from the rod. Courtesy mirrors Lift the cover 3. Nothing should be placed on the floor area in front of the driver as such objects...
Page 251 PASSENGER COMPARTMENT STORAGE, FITTINGS (2/5) Centre console storage Cup holders 6 Raise the button 8 to ventilate the stor- age according to the temperature set compartment 5 This can be used for storing a mobile by the air conditioner. Lower the button ashtray, cup holder, etc.
Page 252 PASSENGER COMPARTMENT STORAGE, FITTINGS (3/5) Front centre armrest storage Glove box Grab handle 13 compartment 11 To open the glove box, lift the catch 12. This offers support and can be held when the vehicle is being driven. With the sliding armrest 9 in its rear- most position, lifting the control 10 and Do not use it for getting into or out of raise the armrest.
Page 253 PASSENGER COMPARTMENT STORAGE, FITTINGS (4/5) Grab handle 13 and clothes Coin holder 15 Sunglasses holder 16 hooks 14 (depending on the vehicle) (depending on the vehicle) Push 16 to open the sunglasses holder. 3.31...
Page 254 PASSENGER COMPARTMENT STORAGE, FITTINGS (5/5) Front seat storage pockets 17 Rear armrest with cup holder Rear door storage compartment 19 Pull down the armrest 18. When turning corners, Ensure that no hard, heavy accelerating or braking, or pointed objects are ensure that the recepta- placed in the “open”...
Page 255: Ashtray, Cigarette Lighter, Accessories Socket
ASHTRAY, CIGARETTE LIGHTER, ACCESSORIES SOCKET Ashtray location 1 Accessories sockets 3 They are provided for connecting ac- Cigarette lighter or cessories approved by our Technical Department. accessories sockets 2 With the ignition on, push in the ciga- rette lighter 2 - it will spring back with a click when it is ready.
Page 256: Rear Headrest
REAR HEADRESTS Position for use Centre seat headrest storage Note: When the headrest need to be reassembled, pay attention to its posi- position Lift the headrest fully until it locks. Make tion which is drawn in the label. sure it is properly locked. Press the button A and lower the cen- tral headrest completely.
Page 257: Rear Bench Seat
REAR BENCH SEAT (1/3) To replace the seatback, proceed in the reverse order to removal. Refit the seatback and click it back into place. When refitting the seat- back, make sure it is cor- rectly locked in place. To manually fold down the If seat covers are fitted, seatbacks The configuration of the...
Page 258 REAR BENCH SEAT (2/3) To automatically fold down Conditions of use the seatbacks (flat position) – Vehicle stationary; Place seat belt in hook 2 to avoid dam- – tailgate open; aging the belt. From the boot, pulling – rear seat belts unlocked. the control 3 enables you to automati- cally unlock the rear bench seatbacks Operating fault...
Page 259 REAR BENCH SEAT (3/3) Press the left side of the switch to select the warmest setting or the right side of the switch to select the average setting. The middle position of the switch is off. The indicator light in the switch lights off.
Page 260: Boot
BOOT To open Opening the doors manually from the inside Press button 1 and lift the tailgate. If it is impossible to unlock the tailgate, it can be done manually from inside: To close – access the luggage compartment by Lower the tailgate using the handles 2 tilting the rear bench seatback(s), inside the tailgate to help you.
Page 261: Automatic Tailgate
AUTOMATIC TAILGATE (1/5) Conditions of use Opening/Closing Depending on the equipment, the tail- gate locks and unlocks at the same – Immobilise the vehicle. When the motorised tailgate opening or time as the doors. closing function is activated using the –...
Page 262 With the ignition off, press and hold Press control 2. Press control 3. switch 1 on the RENAULT card. As a safety precaution, the doors should only be opened or closed when the vehicle is stationary. Risk of injury.
Page 263 3 seconds before triggering the closure work if the vehicle is equipped with a (a beep is emitted every second). With the RENAULT card on your person towbar or is in an area of high elec- behind the tailgate, perform a forwards/ tromagnetic radiation.
Page 264 AUTOMATIC TAILGATE (4/5) Stopping the tailgate Press a tailgate opening/closing control to resume the tailgate operation. manoeuvre Note: detection is inactive in the last The automatic tailgate manoeuvre can centimetre before the tailgate is com- be stopped at any time by a short press pletely closed.
Page 265 AUTOMATIC TAILGATE (5/5) Precautions during use Operating faults Before opening/closing the tailgate, If you activate the automatic tail- ensure that the surrounding space is gate continuously for around a minute sufficient to allow the tailgate to ope- (sequence of opening and closing), it rate.
Page 266: Luggage Cover 2
LUGGAGE COMPARTMENT COVER Removing/refitting the luggage cover 2 Press the two ends 4 to maximum and move them towards the centre of the luggage compartment cover, then tilt the cover. To fit the luggage cover, carry out this procedure in reverse. To unfold the luggage To remove the flexible compartment cover 2...
Page 267: Luggage Net
LUGGAGE NET (1/2) Fitting the luggage net Depending on the vehicle, this may be – open the U-shaped area 6 to access used when transporting animals or lug- the anchoring point 4; behind the front seats gage to isolate them from the passen- –...
Page 268 LUGGAGE NET (2/2) Fitting the luggage net – latch the hook 10 to the anchoring point 11; behind the rear seats – adjust the net strap 9 so that it is taut. Inside the vehicle on each side: The seatbacks must not touch the –...
Page 269 BOOT FITTINGS Anchorage points Attachment points 1. Maximum weight on trunk board 2 is 60kg. If your vehicle is not equipped with anchorage points, you can get them from an authorised dealer. 3.47...
Page 270 TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT Always position the objects transported so that the largest surface is against: – The rear bench seatback for normal loads (example A). – The front seatbacks with the rear seatbacks folded down, the mobile floor in the flat-floor position (exam- ple B).
Page 271: Transporting Objects
TRANSPORTING OBJECTS towbar Permissible nose weight, maxi- mum permissible towing weight, braked and unbraked: ➥ 6.8 Choice and fitting of towing equipment Maximum weight of towing equip- ment: 42 kg It is not permitted to install a me- chanical coupling device (ball joint, hook, etc.) that can be removed without tools or that can be re- tracted, that cannot be easily re-...
Page 272: Roof Bars, Spoiler
ROOF BARS, SPOILER Precautions during use Handling the tailgate Before handling the tailgate, check the objects and/or accessories (bike rack, roof box, etc.) fitted to the roof bars: these must be correctly positioned and secured, so as not to hinder the opera- tion of the tailgate.
Page 273: Multimedia Equipment
MULTIMEDIA EQUIPMENT (1/2) Multimedia systems Hands-free telephone integrated control 1 Multimedia screen; For equipped vehicles, use the steering 2 Steering column controls; wheel controls 3. 3 Steering wheel controls; 4 Microphone. Using the telephone We remind you of the need to conform to the legislation in force concerning the use Refer to the equipment instructions...
Page 274 MULTIMEDIA EQUIPMENT (2/2) Multimedia sockets 6 Sockets USB can only recharge acces- sories with a maximum power rating of 10.5 Watts (voltage: 5V) per socket, which have been approved by our Technical Department. Multimedia sockets 5 The sockets USB can also recharge accessories with a maximum power You can use sockets USB to access the rating of 10.5 Watts (voltage: 5V) per...
Page 275 Section 4: Maintenance Bonnet ............... . Engine oil level: general information .
Page 276: Bonnet
BONNET (1/2) Do not press down on the bonnet: there is a risk that the bonnet may accidentally close. Unlocking the bonnet catch To open, pull handle 1. When working in the engine To unlock, push tab 2 at the same time compartment, ensure that as opening the bonnet.
Page 277 BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and guide it down, allowing a 30 cm gap before it is closed, then release it. It will latch automatically under its own weight.
Page 278: Engine Oil Level: General Information
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for – Remove the dipstick and wipe with a lubrication and cooling of moving parts clean, lint-free cloth; and it is normal to top up the level be- –...
Page 279: Engine Oil Level: Topping Up, Filling
ENGINE OIL LEVEL: topping up, filling (1/2) Topping up/filling – wait for approximately 10 minutes to allow the oil to flow into the engine; The vehicle must be parked on level – check the level using the dipstick 2 ground and the engine should be cold (as described above).
Page 280 ENGINE OIL LEVEL: topping up, filling (2/2) Adding engine oil Use a funnel or protect the filling neck area to avoid engine oil escaping on to a hot part of the engine compartment or a sensitive part (e.g. electrical In order to prevent splashback, it is components).
Page 281: Engine Oil Level: Oil Change
ENGINE OIL LEVEL: OIL CHANGE Oil change Engine oil grade Service interval: refer Refer to the maintenance document for Maintenance Document for your vehi- your vehicle. Filling and/or checking cle. the oil level: when topping up or checking the oil level, Oil change capacity ensure that no oil leaks onto Consult your approved dealer at...
Page 282: Levels
LEVELS, FILTERS (1/3) Frequency of checking coolant level Replacement interval Check the coolant level regularly Refer to the Maintenance Document for (very severe damage is likely to be your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure:...
Page 283: Brake Fluid
LEVELS, FILTERS (2/3) Level 2 It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI” warn- ing line. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking pro- cedure from the manufacturer’s net-...
Page 284: Windscreen Washer Reservoir
LEVELS, FILTERS (3/3) Filters The replacement of filter components (air filter, cabin filter, diesel filter, etc.) is scheduled in the maintenance opera- tions for your vehicle. Replacement intervals for filter el- ements: refer to the Maintenance Document for your vehicle. Liquid ...
Page 285: Tyre Pressure
TYRE PRESSURE (1/2) Label A B: dimension of the tyres fitted to the vehicle. Open the driver’s door to read it. C: front tyre pressure. Tyre pressures should be checked D: rear tyre pressure. when the tyres are cold. Vehicle fitted with a tyre E: tyre pressure for the emergency If the tyre pressures cannot be checked pressure...
Page 286 TYRE PRESSURE (2/2) Special note concerning fully laden vehicles (Maximum Permissible All-Up Weight) and towing a trailer: the maxi- mum speed must be limited to 60 mph (100 kph) and the tyre pressure in- creased by 0.2 bar. ➥ 6.8 Tyre safety and use of snow chains: ➥...
Page 287: Battery
BATTERY (1/2) Depending on the vehicle, a system continuously checks the battery charge status. If this decreases, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. The message will go off. The charge status of your battery can decrease especially if you use your ve- hicle:...
Page 288 BATTERY (2/2) Replacing the battery As this operation is complex, we advise you to contact an approved Dealer. Label A Observe the indications on the battery: – 2 Naked flames and smoking are for- bidden; – 3 eye protection required; –...
Page 289: Bodywork Maintenance
BODYWORK MAINTENANCE (1/3) You should A well-maintained vehicle will last Respect local regulations about wash- longer. It is therefore recommended to ing vehicles (e.g. do not wash your ve- Wash your car frequently, with the maintain the exterior of the vehicle reg- hicle on a public highway).
Page 290 BODYWORK MAINTENANCE (2/3) What you should not do Degrease or clean using high-pressure Wash the vehicle in bright sunlight or cleaning equipment or freezing temperatures. by spraying on prod- Do not scrape off mud or dirt without ucts not approved pre-wetting.
Page 291 BODYWORK MAINTENANCE (3/3) Vehicles with a matte paint Using a roller type car wash Cleaning stickers, decorative finish films, etc. Return the windscreen wiper stalk to the Park position. ➥ 1.92 Check the This type of paint requires certain pre- You should do the following mounting of external accessories, ad- cautions.
Page 292: Interior Trim Maintenance
INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g.: instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, mul- larly.
Page 293 INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in Position objects such as deodorants, the vehicle scents etc. near air vents as this could damage your dashboard trim. If you need to remove equipment in order to clean the passenger com- partment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driv-...
Page 294 4.20...
Page 295 RENAULT card: battery ........
Page 296: Puncture, Emergency Spare Wheel
PUNCTURE, EMERGENCY SPARE WHEEL (1/2) In case of puncture Depending on the vehicle, a tyre infla- tion kit or emergency spare wheel is provided (refer to the following pages). Special note The Tyre Pressure Monitor function does not check the emergency spare wheel (the wheel replaced by the emer- gency spare wheel disappears from the instrument panel display).
Page 297 PUNCTURE, EMERGENCY SPARE WHEEL (2/2) Emergency spare wheel A Do not touch the exhaust system. To get to it: Risk of burns. – open the tailgate; – remove the mobile floor 1; – remove the tool kit box by lifting it by its handles;...
Page 298 TYRE PRESSURE KIT (1/3) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
Page 299 TYRE PRESSURE KIT (2/3) With the engine running and the – after a maximum of 10 minutes, stop parking brake applied, inflating and read the pressure (on pressure gauge 1). – Unscrew the cap from recess 3 on the bottle; Note: while the container is empty- ing (approximately 30 seconds), the –...
Page 300 TYRE PRESSURE KIT (3/3) Precautions when using the – Affix the driving recommendation label to the dashboard where it can easily be seen by the driver; The kit should not be operated for more – Put the kit away. than 10 consecutive minutes. –...
Page 301: Tools
TOOLS Jack 2 Fold it correctly before refitting it in its housing. Jack handle 3 This tightens or releases the tow eye 4 Tow eye 4 ➥ 5.29 Wheelbrace 1 The presence of the tools depends on the vehicle. Locks or unlocks the wheel bolts and The tools are located in a tray under the tow eye 4.
Page 302: Changing A Wheel
CHANGING A WHEEL (1/2) Attach the wheelbrace 1 and the jack handle 6 (in groove 5). Turn the wheelbrace until the wheel lifts off the ground. Vehicles equipped with a jack, wheelbrace and jack handle If the vehicle is not equipped with a If necessary, remove the wheel trim.
Page 303 CHANGING A WHEEL (2/2) Turn it a few times to lift the wheel off the ground. Undo the bolts and take off the wheel. Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub.
Page 304: Tyres (Tyre And Wheel Safety, Use In Winter)
TYRES (1/3) The tyres are the only contact between When the tread has worn down to the the vehicle and the road, so it is essen- wear warning strips, these strips will become visible 2: it is then necessary tial to keep them in good condition. to replace your tyres because the tread You must make sure that your tyres con- rubber is now only 1.6 mm deep at...
Page 305 TYRES (2/3) Tyre pressures The pressures should be checked cold: Vehicle fitted with a tyre pressure ignore higher pressures which may be monitoring system Adhere to the tyre pressures (including reached in hot weather or following a In cases of under-inflation (puncture, the emergency spare wheel).
Page 306 TYRES (3/3) Fitting new tyres Changing a wheel Snow chains may only be fitted to tyres of the same As the tyre pressure monitor For your safety, please re- size as those originally fitted may take several minutes to spect the speed limit. to your vehicle.
Page 307: Headlights (Changing Bulbs)
FRONT HEADLIGHTS: changing bulbs LED front fog lights 11 Additional lights Depending on the vehicle, please see If you wish to fit fog lights to your ve- an authorised dealer. hicle, please see an authorised dealer. LED Direction indicator light 12 Please see an authorised dealer.
Page 308 REAR AND SIDE LIGHTS: changing bulbs (1/3) Side lights and brake lights 1 Direction indicators 2 or 4 (depending on the vehicle) Consult an approved Dealer. Consult an approved Dealer. LED reversing light 3 (depending on the vehicle) Consult an approved Dealer. 5.14...
Page 309 REAR AND SIDE LIGHTS: changing bulbs (2/3) Halogen reversing lights Turn bulb holder 6 fully anticlockwise and change the bulb. (depending on the vehicle) Open the tailgate. Refitting Unclip the trim 5 and remove it. To refit, proceed in the reverse order, taking care not to damage the wiring.
Page 310 REAR AND SIDE LIGHTS: changing bulbs (3/3) High level brake light 7 Halogen number plate Side indicator lights 10 lights 9 Consult an approved dealer. Consult an authorised dealer. (depending on the vehicle) – Unclip the light 9 (using a tool such Rear fog lights 8 as a flat-blade screwdriver).
Page 311: Interior Lighting: Changing Bulbs
INTERIOR LIGHTING: changing bulbs (1/2) Map reading lights 1 Ambient lights 2 Glove box lights 3 Please consult an authorised dealer. Please consult an authorised dealer. Please consult an authorised dealer. The bulbs are under pres- sure and can break when replaced.
Page 312 INTERIOR LIGHTING: changing bulbs (2/2) Front door lights 4, front and Boot lights 6 rear door ambient light 5 Unclip light 6 by pressing the tabs on each side (using a flat-blade screw- Please consult an authorised dealer. driver or similar). Disconnect the light.
Page 313: Renault Card: Battery
RENAULT lock/unlock the vehicle. ➥ 1.13 Note: it is not advisable to touch the card: electronic circuit or contacts on the –...
Page 314: Radio Frequency Remote Control Unit: Batteries
RADIO FREQUENCY REMOTE CONTROL: batteries Replacing the battery Note: It is not advisable to touch the electronic circuit in the key cover when Open the case at slot 1 using a flat- replacing the battery. blade screwdriver or similar, and re- place the battery 2, observing the po- larity shown on the back of the cover.
Page 315: Fuses
FUSES (1/3) Fuses in passenger compartment A on the right-hand side of the vehicle Glove box needs to be disassembled to access the fuses. Please consult an au- thorised dealer. If any electrical component does not Fuses in passenger compartment B work, check the condition of the fuses.
Page 316 FUSES (2/3) Use the fuse allocation label in the stor- age compartment A or B to identify the fuses. Certain fuses should only be replaced by a qualified professional. These fuses are not listed on the label. Only change the fuses represented on the label.
Page 317 FUSES (3/3) Allocation of fuses (the presence and location of certain fuses depends on the vehicle equipment level) Symbol Allocation Symbol Allocation Symbol Allocation Vehicle dynamic BLOWER Ventilation H/MIRR Heated door mirrors control TURN HEATER Hazard lamp STOP LAMP Stop lamp Heater seat HAZARD SEAT...
Page 318: Battery
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (cour- The battery charger must be com- tesy lights, etc.) are switched off patible with a battery with nominal before disconnecting or reconnect- voltage of 12 volts.
Page 319 BATTERY: troubleshooting (2/2) Starting the vehicle using the If your vehicle’s engine does not start immediately, switch off the ignition and battery from another vehicle wait a few seconds before the repeat- If you have to use the battery from an- ing the operation.
Page 320: Accessories
INSTALLATION AND USE OF ACCESSORIES: important recommendations Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Before plugging an accessory into an outlet, make sure you do not exceed the maximum power allowed on the outlet.
Page 321: Wipers (Replacing Blades)
WINDSCREEN WIPER BLADES: replacement (1/2) Refitting Slide the blade along the arm until it clips on. Check that it is correctly locked in place. Lower the windscreen wiper arm carefully. With the ignition on, return the wind- screen wiper stalk to the stop position. The blade on the driver’s side must always be above the passenger blade.
Page 322 WINDSCREEN WIPER BLADES: replacement (2/2) To refit To refit the wiper blade, proceed in re- verse order to removal. Make sure that the blade is correctly locked in position. Rear screen wiper blade 4 Stalk in stop position (deactivated): – Lift the wiper arm 6; –...
Page 323 Insert the key into the ignition or, de- it with the front wheels off the ground. pending on the vehicle, having the RENAULT card on you, press the In exceptional circumstances, you may tow it with all four wheels on the ground,...
Page 324 TOWING: breakdown recovery (2/4) 2WD vehicles When setting off, if the lever is locked in position P even though you are pres- Vehicles fitted with an automatic sing the brake pedal, the lever can be transmission or continuously va- released manually. To do this, unclip riable transmission.
Page 325 TOWING: breakdown recovery (3/4) 4WD vehicles Whichever type of gearbox is fitted, a 4WD vehicle must never be towed if any of its 4 wheels are touching the ground. vehicle must never be towed if one of its 4 wheels is touching the ground.
Page 326 TOWING: breakdown recovery (4/4) Do not leave the tools unse- cured inside the vehicle as they may come loose under braking. – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed Access to towing points Only use the front towing point A must be able to brake.
Page 327 Dealer as soon as possible. Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or Card battery is flat. Replace the battery. You can still lock/ unlock the doors. unlock and start your vehicle. ➥ 1.13 and ➥...
Page 328: Operating Faults
OPERATING FAULTS (2/7) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. Using the remote control POSSIBLE CAUSES ACTION REQUIRED The remote control does not lock or The remote control battery is flat.
Page 329 Faulty circuit. Consult an approved dealer. The engine will not start. Starting conditions are not ➥ 2.4 or ➥ 2.5 fulfilled. The RENAULT card does ➥ 2.5 not work. The engine cannot be switched off. Card not detected. ➥ 2.5 Electronic fault.
Page 330 OPERATING FAULTS (4/7) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pres- Check the tyre pressures: if this is not the sures, incorrectly balanced or dam- problem, have them checked by an ap- aged. proved Dealer.
Page 331 OPERATING FAULTS (5/7) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Drive carefully at reduced speed, be aware of the level of force in the steering wheel Fault with the electric assistance needed to turn the wheels. Consult an ap- motor.
Page 332 OPERATING FAULTS (6/7) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse. ➥ 5.21 The wiper does not stop. Faulty electrical controls.
Page 333 OPERATING FAULTS (7/7) Electrical equipment POSSIBLE CAUSES WHAT TO DO Traces of condensation in the head- Traces of condensation may be a nat- lights or rear lights ural phenomenon caused by varia- tions in temperature and humidity. In this case, the traces will disappear slowly once the lights are switched The front seat belt reminder light An object is stuck between the floor...
Page 334 5.40...
Page 335 Section 6: Technical specifications Vehicle identification plate ............Technical Information for the emergency services .
Page 336: Vehicle Identification Plate
VEHICLE IDENTIFICATION PLATES The information shown on the ve- 6 MMTA (Maximum Permissible hicle identification plate should be Weight) for front axle. quoted on all correspondence or 7 MMTA on rear axle. orders. 8 Built date information. 9 Diesel exhaust emissions. The presence and location of the in- Depending on the vehicle, this formation depends on the vehicle.
Page 337: Technical Information For The Emergency Services
TECHNICAL INFORMATION FOR THE EMERGENCY SERVICES The QR Code on the A label allows emergency workers using a tablet or smartphone to immediately access the technical information useful for working on the vehicle in the event of an acci- dent. Ensure that the A label is always visible and present on the windscreen as well as the rear screen.
Page 338: Engine Identification Plate
ENGINE IDENTIFICATION PLATES Please quote the information on the engine plate or label A in all corre- spondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
Page 339: Dimensions
DIMENSIONS (in metres) 0,929 2,705 1,038 1,587-1,597 4,672 1,673-1,678 1,582-1,592 2,063...
Page 340: Engine Specifications
ENGINE SPECIFICATIONS (1/2) Versions 2.0 GDi 2.5 16V 1.3 Tce 2.0 dCi 2.0 dCi Engine type QR25 H5H Turbo M9R Turbo (see engine plate) Cubic capacity 1997 2488 1333 1995 1997 (cc) Type of fuel Petrol Diesel Octane rating It is essential that you use unleadedpetrol of the octane rating The label located in the fuel filler flap indi- stated on the label inside the fuel filler flap.➥...
Page 341 ENGINE SPECIFICATIONS (2/2) Versions 2.0 GDi 2.5 16V 1.3 Tce 2.0 dCi 2.0 dCi Engine type QR25 H5H Turbo M9R Turbo (see engine plate) Cubic capacity 1997 2488 1333 1995 1997 (cc) Spark plugs Only use the spark plugs specified for your vehicle’s engine. The type should be marked on a labelaffixed inside the engine compartment.
Page 342: Towing Weights
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on your vehicle’s equipment. Consult your approved Dealer. Maximum Authorised Mass (MMAC) Maximum Permissible Weight (MMTA) Weights are indicated on the vehicle identification plate. ➥ 6.2 Gross Train Weight (MTR) Braked Trailer Weight* found by calculating: MTR - MMAC...
Page 343: Replacement Parts And Repairs
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
Page 344: Service Sheets
SERVICE SHEETS (1/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 345 SERVICE SHEETS (2/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 346 SERVICE SHEETS (3/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 347 SERVICE SHEETS (4/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 348 SERVICE SHEETS (5/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 349 SERVICE SHEETS (6/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 350: Anticorrosion Check
ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.16...
Page 351 ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
Page 352 ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...
Page 353 ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.19...
Page 354 ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.20...
Page 355 ALPHABETICAL INDEX (1/6) automatic gearbox selector lever......2.98 → 2.100 4 wheel drive (4WD) ..........2.37 → 2.40 automatic trunk lid ..........3.39 → 3.43 ABS ..............1.60, 2.32 → 2.36 battery access troubleshooting ..........5.24 – 5.25 vehicle ................0.2 battery.......... 0.8, 4.13 – 4.14, 5.24 – 5.25 accessories................
Page 356 ALPHABETICAL INDEX (2/6) courtesy light ..........3.25 → 3.27, 5.17 emergency braking ..........2.32 → 2.36 courtesy mirrors ..............3.28 emergency key ............1.5 → 1.7 cruise control ..........1.61, 2.70 → 2.73 emergency spare wheel ..........5.2 – 5.3 cruise control-speed limiter........2.67 → 2.73 engine coolant ..............
Page 357 ALPHABETICAL INDEX (3/6) filling ............1.58, 1.100 → 1.102 instrument panel messages ......1.66 → 1.75 grade ............1.100 → 1.102 interior trim fuel consumption ...........2.22 → 2.26 maintenance ............. 4.18 – 4.19 fuel economy ............2.22 → 2.26 Isofix ............... 1.41 – 1.42 fuel filler cap ............1.100 →...
Page 358 ............... 5.20 opening the doors ..........1.13 → 1.17 remote control door locking unit ........1.2 → 1.4 operating faults ........ 1.58 → 1.63, 5.33 → 5.39 RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.18 overspeed warning ..........2.64 → 2.66 RENAULT card battery ................5.19 use ...........
Page 359 ALPHABETICAL INDEX (5/6) roof rack tanks and reservoirs roof bars ............... 3.50 brake fluid ..............4.9 running in ..............2.2 – 2.3 coolant ................4.8 tanks and reservoirs: windscreen washer ............4.10 safety distance warning .........2.61 → 2.63 technical specifications ........6.5, 6.8 – 6.9 safety distances .............2.61 →...
Page 360 ALPHABETICAL INDEX (6/6) vehicle identification ............. 0.7, 6.2 vehicle identification number (VIN) ....... 0.7, 6.2 vehicle identification plates ........0.7, 6.2, 6.4 ventilation ............1.23, 3.2 → 3.16 warning lights............1.58 → 1.75 washing ..............4.15 → 4.17 weights ................6.8 wheelbrace ................5.7 wheels (safety) ............5.10 →...
Page 362 à999109432Sì ï ê ä SS RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 122-122 BIS, AVENUE DU GENERAL LECLERC 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / renaultgroup.com...

Renault KOLEOS 2023 Vehicle User Manual

Section 1: Getting to Know Your Vehicle

Section 2: Driving

Section 3: Your Comfort

Section 4: Maintenance

Section 5: Practical Advice

Quick Links

Chapters

Need help?

Questions and answers

Related Manuals for Renault KOLEOS 2023

Summary of Contents for Renault KOLEOS 2023

Table of Contents