Table of Contents
Advertisement
This Owner's Manual contains the information necessary:
– for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and
the technical developments it incorporates.
– to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular main-
tenance.
– to enable you to deal quickly with minor faults not requiring specialist attention.
It is well worth taking a few minutes to read this manual to familiarise yourself with the information and guidelines it contains about
the vehicle and its functions and new features. If certain points are still unclear, our Network technicians will be only too pleased
to provide you with any additional information.
The following symbol will help you when reading this manual:
To indicate a hazard, danger or safety recommendation.
The descriptions of the models given in this manual are based on the technical specifications at the time of writing. This manual
covers all items of equipment (both standard and optional) available for these models, but whether or not these are fitted
to the vehicle depends on the version, options selected and the country where the vehicle is sold.
This manual may also contain information about items of equipment to be introduced later in the model year.
Throughout the manual, the "approved dealer" is your RENAULT dealer.
Enjoy driving your new vehicle.
Translated from English. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from the vehicle manufac-
turer.
Welcome aboard your vehicle
0.1
Advertisement
Chapters
Table of Contents
Related Manuals for Renault KWID
Summary of Contents for Renault KWID
- Page 1 This manual may also contain information about items of equipment to be introduced later in the model year. Throughout the manual, the “approved dealer” is your RENAULT dealer. Enjoy driving your new vehicle.
- Page 3 Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........Radio ..............
-
Page 5: Table Of Contents
Section 1: Getting to know your vehicle Keys, radio frequency remote control: general information ....... . Locking and unlocking the doors . -
Page 6: Keys, Radio Frequency Remote Control: General Information
KEYS, RADIO FREQUENCY REMOTE CONTROL: general information(1/2) Driver’s responsibility: Never leave your vehicle with the keys inside when leaving a child (or animal) in the car, even for a short period. The reason for this is that the child may endanger himself or others by starting the engine, activating equipment such as the window winders for... - Page 7 KEYS, RADIO FREQUENCY REMOTE CONTROL: general information(2/2) The remote control unit Replacement and additional keys or remote controls operating range If you lose your remote control key or This varies according require another, you can obtain one environment. It is therefore important from an approved dealer.
-
Page 8: Locking And Unlocking The Doors
LOCKING AND UNLOCKING THE DOORS Manual control Locking the doors without From the inside the radio frequency remote Push in button 2 to lock and lift button 2 From the outside control to unlock. It is impossible to open the Unlock the driver door using the key in door if 2 is pushed in. -
Page 9: Opening And Closing The Doors
OPENING AND CLOSING THE DOORS(1/2) Opening the doors from the Opening from the inside outside Pull handle 2. With the doors unlocked (refer to the As a safety precaution, information on “Locking/unlocking the the doors should only be doors” in Section 1), place your hand opened or closed when the on the handle 1 and pull towards you. - Page 10 OPENING AND CLOSING THE DOORS(2/2) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-sufficient alone on your vehicle, even for a short time. They may pose a risk to themselves or to others by starting the engine, activating equipment such as the electric windows or by locking the...
-
Page 11: Engine Immobiliser
ENGINE IMMOBILISER (Depends on vehicle) Engine Immobiliser prevents the vehicle being driven by anyone not in possession of the vehicle’s coded ignition key. Operating principle The vehicle is automatically protected a few seconds after the ignition is switched off. If the vehicle does not recognise the coded ignition key or wrong key is used, the engine cannot be started. -
Page 12: Front Seats
FRONT SEATS To tilt the seatback Lift knob 2 upward to unlock recliner mechanism.Tilt the seat back to desired position and release knob. Ensure seat back is locked properly after release. Move forward or backward Lift the lever 1 to release and move the seat forward or backward.Release the lever 1 in desired position of seat and For safety reasons, carry... -
Page 13: Seat Belts
SEAT BELTS (1/3) Before starting, first adjust your Always wear your seat belt when driving position, then ask all travelling in your vehicle. You must occupants to adjust their seat belts also comply with the legislation of the to ensure optimum protection. particular country you are in. - Page 14 SEAT BELTS (2/3) – m o d i f i c a t i o n may be made to the component parts of the originally fitted restraint system:seat belts,seats their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...
- Page 15 SEAT BELTS (3/3) Adjusting the rear seat belts Follow the same intstructions of front seat belts to adjust/fasten/unolcking the rear seat belts. Adjust the seat belt strap as indicated in the image for height adjustment. 1.11...
-
Page 16: Safety Systems In Addition To The Seat Belts
SAFETY SYSTEMS IN ADDITION TO THE SEAT BELTS (1/2) Warnings concerning the driver’s air bag – Have the entire restraint – Do not modify the steering system checked following an accident. wheel or the steering wheel boss. – No operation whatsoever –... - Page 17 SAFETY SYSTEMS IN ADDITION TO THE SEAT BELTS (2/2) Operation Air bag system consists of : – an airbag and gas generator fitted on This system is only operational when the steering wheel for the driver ; the ignition is switched on. –...
- Page 18 CHILD SAFETY: general information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing.
- Page 19 CHILD SAFETY: general information (2/2) Using a child seat Set a good example by always The level of protection offered by the fastening your seat belt and child seat depends on ability to restrain teaching your child: child and on its installation. Incorrect –...
- Page 20 CHILD SAFETY: fitting a child seat (1/5) In the front seat Some seats are not suitable for fitting child seats. The diagram on the The laws concerning children travelling following page shows you how to attach in the front passenger seat differ in a child seat.
- Page 21 CHILD SAFETY: fitting a child seat (2/5) In the rear side seat A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest the door. Before fitting a child seat to the ISOFIX anchorages on the rear side seat, ensure that the seat belt buckles are not positioned between the two ISOFIX...
-
Page 22: Child Safety
CHILD SAFETY: fitting a child seat (3/5) Visual installation of the five-seater version Child seat attached using the belt ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt. ² Seat not suitable for fitting child seats. - Page 23 CHILD SAFETY: fitting a child seat (4/5) The table below summarises the information already shown in the diagram on the following pages, to ensure the applicable regulations are respected. Seating Position Rear Outboard Weight of Front passenger Rear Intermediate Intermediate Mass Group the child seat...
- Page 24 CHILD SAFETY: fitting a child seat (5/5) Refer to the “Child safety equipment” booklet available from the network to choose the seat suited to your child and recommended for your vehicle. X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal”...
-
Page 25: Driving Positon - Right Hand Drive
DRIVING POSITION, RIGHT-HAND DRIVE (1/2) 1.21... - Page 26 DRIVING POSITION, RIGHT-HAND DRIVE (2/2) The presence of the equipment DEPENDS ON THE VEHICLE VERSION AND COUNTRY. 1 Side air vent. 9 Side air vent. 16 Handbrake. 2 Upper Glove Box 10 Beam height adjustment control. 17 Cigarette lighter or accessories socket.
-
Page 27: Warning Lights
WARNING LIGHTS (1/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. á Main beam headlight tell-tale Ò light Orange warning light comes on while you are driving, drive carefully Dipped beam headlight to an authorised dealer as soon telltale as possible. - Page 28 WARNING LIGHTS (2/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Ú Ò Handbrake “on” warning Battery charge warning light Warning light malfunction light and brake circuit (red or orange) If it comes on when you are incident warning light driving, it indicates that the circuit Warning light (orange)
- Page 29 WARNING LIGHTS (3/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Ä Coolant temperature and Warning light for monitoring Oil Pressure Warning Light exhaust gas It comes on when the ignition is switched It comes on when the ignition is on and then goes out.
-
Page 30: On-Board Computer
ON-BOARD COMPUTER (1/2) d) Average Fuel Consumption (from For the first few kilometres after last reset) ; pressing the reset key you will notice e) Current Fuel Consumption ; that the range increases as you travel. f) Estimated Fuel range (DTE - distance This range takes into account the to empty) ;... - Page 31 ON-BOARD COMPUTER (2/2) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Interpreting the display selected DISPLAY Total mileage recorder Trip mileage recorder Fuel used (since the last time the reset button was pressed) Average fuel consumption (since the last time the reset button was pressed) This value is displayed after driving 400 metres.
-
Page 32: Exterior Lighting And Signals
EXTERIOR LIGHTING AND SIGNALS á Main beam headlights With the dipped beam head- lights lit, push stalk 3. The indicator on instrument panel comes on.To return to dipped headlight,pull the stalk 3 upward. Switching off the lights Turn the end of stalk 3 until the symbol is opposite mark 2. -
Page 33: Headlight Height Adjustment
HEADLIGHT HEIGHT ADJUSTMENT Position Only Driver Zero Driver + front passenger Zero Driver + Trunk Driver + All passengers Driver + All passengers+Trunk Headlight height Adjustment: Knob A is used to adjust height of the headlight beam according to load.Turn control A anticlockwise to lower the beams and clockwise to raise them. -
Page 34: Audible And Visual Signals
AUDIBLE AND VISUAL SIGNALS Horn Hazard warning lights Direction indicators é Press on the centre or sides of the Press switch 2. Move stalk 3 parallel to the steering highlighted (horn pad) to use the horn. wheel and in the direction you are going This switch activates all four direction to turn it. -
Page 35: Mirrors
MIRRORS Objects observed in the door mirror glass are actually closer than they appear. For your safety, take this into account in order to correctly assess the distance before any manoeuvre. Door mirrors with manual Interior rear view mirror 2 adjustment 1 The interior rear-view mirror 2 is manually adjustable. - Page 36 WINDSCREEN WASHING / WIPING Windscreen Washing Keep an eye on the condition of the blade. They should be replaced as soon With the ignition on, pull stalk 1 as they become less efficient. This will towards you(depending on the version). occur approximately once a year.
-
Page 37: Fuel Tank (Filling With Fuel)
FUEL TANK (1/2) Fuel filler cap: this is specific to the vehicle type. If you have to replace it, make sure the new cap is of the same type. Contact an approved dealer. It is essential to use unleaded petrol. Using leaded petrol will damage the antipollution system and may lead to a loss of warranty. - Page 38 FUEL TANK (2/2) Filling up with fuel With the ignition off, insert the nozzle fully before turning it on to fill the fuel tank (risk of splashing). Keep the nozzle in this position throughout the entire filling operation. When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made, as there must be...
- Page 39 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in, Ignition switch ............Starting / Stopping the engine .
- Page 40 RUNNING IN, IGNITION SWITCH Running in Ignition on position M For the first 1,000 km, do not exceed The ignition is switched on: 80 km/h in the highest gear. – the engine may be started. You may only expect top performance from your vehicle after approximately Start position D 3,000 kms...
- Page 41 STARTING/STOPPING THE ENGINE Starting the engine Special note Depending on the vehicle, accessories In cold condition: switch on the ignition (e.g. radio) stop working either when for several seconds before starting the the engine is switched off or when the engine, so that it is easier to start the doors are locked.
- Page 42 STARTING/STOPPING THE ENGINE Starting problems Operating faults such as: – faulty ignition, running out of fuel or To avoid damage , do not keep trying disconnected spark plugs resulting to start the engine (by pushing or towing in the engine misfiring or cutting out the vehicle) without having identified when driving;...
- Page 43 GEAR LEVER, HAND bRAkE (1/2) Gear change indicators Depending on the gradient Depending on the vehicle, to obtain op- and/or vehicle load, it may timum consumption levels, an indicator be necessary when statio- light on the instrument panel lets you nary to apply the brake by know the best time to move up or down at least a further two notches and...
- Page 44 GEAR LEVER, HAND bRAkE (2/2) Depending on the gradient Make sure that the hand- and/or vehicle load, it may brake is properly released Handbrake be necessary when statio- when driving (red indi- nary to apply the brake by To release cator light off), otherwise at least a further two notches and Pull lever 3 up slightly, press button 2...
- Page 45 ADVICE: antipollution, fuel economy and driving (1/3) Engine adjustments Your vehicle has been designed with Have your vehicle adjusted and respect for the environment in mind checked by an authorised dealer, in ac- – ignition: this does not require ad- for its entire service life.
- Page 46 (vehi- cle battery, oil filter, air filter, batter- ies, etc.) and oil containers (empty or filled with used oil) must be dis- posed of through authorised Renault Driving Dealer – Drive carefully for the first few kilo- metres until the engine reaches –...
- Page 47 ADVICE: antipollution, fuel economy and driving (3/3) Exhaust gas monitoring – Poor weather conditions, flooded roads. Do not drive through water if it system is higher than the lower edge of the This system detects operating faults wheel rim. in the vehicle’s antipollution system. These faults may cause mechanical –...
- Page 48 AUTOMATED MANUAL TRANSMISSION (1/4) Gear Rotary Shifter 1 Gear shift pattern Display This allows you to engage forward Align the letters R/N/D to the red The engaged gear (R/N/D) is indicated pointer. on the instrument panel display 2. gear, reverse and neutral. A where R/N/D stands for: In case, gear is not engaged properly, letter R or D will blink on the cluster.
- Page 49 AUTOMATED MANUAL TRANSMISSION (2/4) Starting the engine Creeping Similar vehicle Switch ON ignition. To start engine, It is a function that enables the vehicle equipped with a manual keep the key in ignition and wait for 3 to move very slowly without depressing gearbox,this vehicle is also seconds to initiate starting sequence.
- Page 50 AUTOMATED MANUAL TRANSMISSION (3/4) Driving in automatic mode However, if the system does not When stopped at traffic lights, with the shift automatically, shift gear knob to gear engaged in “D”,keep the ve- When ignition is switched ON, start the “N”...
- Page 51 AUTOMATED MANUAL TRANSMISSION (4/4) Accelerating and overtaking Precautions in Drive mode Towing your automated manual transmission vehicle –Slowly depress the accelerator pedal – If vehicle kept sta- to accelerate gradually. t i o n a r y s l o p e f o r If the gear is engaged in R/D, too long without applying the brakes...
- Page 52 2.14...
- Page 53 Section 3: Your comfort Air vents, air outlets ............. . Heating, Ventilation, Air conditioning .
-
Page 54: Air Vents, Air Outlets
AIR VENTS, air outlets (1/2) 1 Left-hand side air vent 3 Centre air vents 5 Control panel 2 Windscreen demisting vents 4 Right-hand air vent 6 Front passangers footwell heater outlets... - Page 55 AIR VENTS, air outlets (2/2) Air flow Centre Air Vents (depends on the vehicle) Lateral Air vents(Left and Right) To open, press on the air vent,(point To open, press on the air vent (point 1) 3/4) until it is open as far as required. until it is open as far as required.
-
Page 56: Heating, Ventilation, Air Conditioning
HEATING, VENTILATION, AIR CONDITIONING (1/2) Adjusting the ventilation fan speed. Turn control 3 from 0 to 4. The further to the right it is positioned, the more air is blown into the passenger compartment. If you want to shut off the flow of air completely and stop the system, set control 3 to 0. - Page 57 HEATING, VENTILATION, AIR CONDITIONING (2/2) Switching passenger Air recirculation is used to: Rapid demisting compartment isolation mode/ – to isolate the passenger compartment Turn controls 1, 3 and 4 to positions air recirculation mode on. from the external atmosphere â –...
-
Page 58: Air Conditioning: Information And Advice On Use
– Reduction in de-icing, demisting conditioning is operating. or air conditioning performance. Advice for reducing consumption Contact an approved Renault Dealer. helping preserve – No cold air is being produced. environment Check that the controls are set... -
Page 59: Windows
WINDOWS Driver’s responsibility If a body part gets trapped, reverse the direction of travel of the window as soon as possible by pressing the relevant switch.Never leave your vehicle with the key inside and never leave a child (or a pet) unsupervised, even for a short while. -
Page 60: Courtesy Light, Sun Visor And Grab Handle
COURTESY LIGHT, SUN VISOR AND GRAB HANDLE Courtesy light Front sun visor Rear Grab handle 3 This feature depends on the vehicle This feature depends on the vehicle This feature depends on the vehicle version. version. version. – Press switch 1 to position A for Lower the sun visor 2 over the This offers support and can be held switching ON the light. - Page 61 PASSENGER COMPARTMENT STORAGE, FITTINGS Upper Glove Box 1 Door Storage Compartment 4 Accessories socket 7 They are provided for connecting ac- Open Storage 2 Cup Holder 5, 6 cessories approved by our Technical Department. Lower Glove box 3 .Need to press at the lowest center Connect accessories with of the lid to open and close gently by a maximum power of...
-
Page 62: Rear Seat
REAR SEATS To un-fold the seat back-rest When refitting the seat- Lift up seat back and push to the upright back, make sure it is cor- position until it is latched on both sides. rectly locked in place. If seat covers are fitted, make sure these do not prevent the seatback latch from locking in. -
Page 63: Boot
BOOT To open To close From the inside Pull the lever 2, then lift the boot lid. Lower the boot lid from point 3 using From the outside your hands and properly close it. Insert the key in the boot lock 1, turn it and lift the boot lid. -
Page 64: Multimedia Equipment
MULTIMEDIA EqUIPMENT If your vehicle is not fitted with an audio system, one can be fitted and locations have been provided for the radio 1; To install any equipment, please consult an authorised dealer. Refer Multimedia manual for more details Hands-free telephone The presence and location of this equipment depends on the vehicle’s... - Page 65 Section 4: Maintenance Bonnet ............... . Engine Oil - Topping up, filling .
-
Page 66: Bonnet
Bonnet In the event of even a slight impact involving the radia- tor grille or bonnet, have the bonnet lock checked by an approved Dealer as soon as pos- sible. When working in the engine compartment, ensure that the windscreen wiper stalk is in the park position. -
Page 67: Engine Oil - Topping Up, Filling
enGIne oIL LeVeL: topping up, filling (1/3) It is normal for an engine to use oil for Once operation been lubrication and cooling of moving parts completed, ensure that the dipstick and it is normal to top up the level is guided in as far as it will go or that between oil changes. - Page 68 enGIne oIL LeVeL: topping up, filling (2/3) – Unscrew cap 1; – top up the level (as a guide, the capacity between the minimum and maximum reading on the dipstick 2 is approximately 0.85 litres,(depending on the engine); – wait for approximately 20 minutes to allow the oil to flow into the engine;...
- Page 69 enGIne oIL LeVeL: topping up, filling (3/3) oil change Service interval: refer Maintenance Document for your vehicle. oil change capacity Please refer to the maintenance docu- ment for your vehicle, or contact an au- thorised dealer. Always check the engine oil level using exceeding the maximum the dipstick, as explained previously (it engine oil level...
-
Page 70: Levels
Brake fluid level Windscreen washer RENAULT and which have been taken This should be checked frequently, from a sealed container. topping up and immediately if you notice even the slightest loss in braking efficiency. -
Page 71: Filters
LeVeLS (2/2) / FILteRS Checking intervals Filters Check the coolant level regularly The replacement of filter elements (very severe damage is likely to be (air filter, cabin filter, fuel filter, etc.) caused to the engine if it runs out of is scheduled in the maintenance coolant). -
Page 72: Battery
BAtteRY (1/2) The charge status of your battery can decrease especially if you use your vehicle: – for short journeys ; – for driving in town ; – when the temperature drops ; – after extended use of consumers (radio etc.) with the engine switched off. - Page 73 BAtteRY (2/2) Replacing the battery As this operation is complex, we advise you to contact an approved Dealer. Label A Observe the indications on the battery: – 2 Naked flames and smoking are forbidden; – 3 Eye protection required; – 4 Keep away from children; –...
-
Page 74: Tyre Pressure
tYRe pReSSURe Adhere to the tyre pressures (including the emergency spare wheel). The tyre tyre Un-Laden Laden pressures should be checked at least Condition Condition Location once a month and additionally before any long journey. Tyre pressures should always be Front checked when the tyres are cold, ignore higher pressures which may be... -
Page 75: Bodywork Maintenance
BoDYWoRk MAIntenAnCe (1/2) What you should not do You should A well-maintained vehicle will last longer. It is therefore recommended Do not degrease or clean mechanical Wash your car frequently, with the to maintain the exterior of the vehicle components (e.g. - Page 76 BoDYWoRk MAIntenAnCe (2/2) Vehicles with a matte paint Using a roller type car wash Respect local regulations about washing vehicles (e.g. do not wash finish Return the windscreen wiper stalk to the your vehicle on a public highway). Park position (refer to the information This type of paint requires certain on the “Windscreen washer, wiper”...
-
Page 77: Interior Trim Maintenance
InteRIoR tRIM MAIntenAnCe (1/2) instrument panel textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. to maintain the interior of the vehicle temperature display, radio display, etc.) regularly. - Page 78 InteRIoR tRIM MAIntenAnCe (2/2) Removal/replacing removable You should not: equipment originally fitted in You are strongly advised not to position the vehicle objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment damage your dashboard trim.
- Page 79 Section 5: Practical advice Puncture, emergency spare wheel ..........Wheel trim, tools .
-
Page 80: Puncture, Emergency Spare Wheel
Puncture, emergency sPare nB: ensure that the emergency spare wheel punctured wheel correctly posi- tioned.Check that boot If the vehicle is parked on carpet is correctly positioned in its spare Wheel the hard shoulder, you must bump stops to prevent it from being warn other road users of damaged. -
Page 81: Wheel Trim, Tools
Wheel trim, tools central wheel trim with accessing the tools visible wheel bolts N e v e r l e a v e t o o l s (example: wheel trim 1) Jack 2 and Wrench 3 unsecured in the vehicle: Depending on the version,the bolts there is a risk that they may Jack 2 is in a jack pouch and is placed... -
Page 82: Changing A Wheel
changing a Wheel (1/2) Switch on the hazard warn- ing lights.Keep the vehicle away from traffic and on a level surface where it will not slip (if necessary, place a solid support under the jack base).Apply the parking brake and engage a removing the Wheel Place the jack under the body ,and gear (first or reverse). - Page 83 changing a Wheel (2/2) refitting the carwheel Ensure the wheel is fastened sufficient If the vehicle is parked on enough, so that removing stud will not the hard shoulder, you must cause the wheel to come out off the warn other road users of -by aligning one of holes to the stud in drum/disc.
-
Page 84: Tyres
tyres (1/3) The tyres are the only contact between When the tread has worn down to the the vehicle and the road, so it is essential wear warning strips, these strips will to keep them in good condition. become visible 2: it is then necessary You must make sure that your tyres to replace your tyres because the tread conform to local road traffic regulations. - Page 85 tyres (2/3) tyre pressures emergency spare wheel The pressures should be checked cold: ignore higher pressures which may be Adhere to the tyre pressures (including Refer to the information on “Changing a reached in hot weather or following a the emergency spare wheel). The tyre wheel”...
- Page 86 tyres (3/3) Fitting new tyres use in winter studded tyres This type of equipment may only be chains used for a limited period and as laid For safety reasons, fitting snow down by local legislation. It is necessary For safety reasons, this op- chains to the rear axle is strictly to observe the speed specified by eration must be carried out...
-
Page 87: Front Lights-Changing Headlamps Main Bulbs
Front lights-changine head lamP main BulB The head lamp bulbs can be replaced. The engine may be hot However, we recommend you to have during operations in close them replaced with the approved dealer proximity.In addition, the if it proves difficult. engine cooling fan may come on at any moment. -
Page 88: Fuses
Fuses (1/3) removing the fuses Remove the fuse, located at the back of flap A from position 1. To remove the fuse, slide the fuse. It is not advisable to use the free fuse locations. The engine may be hot Passenger compartment fuses A Fuses in engine compartment B when working in close... - Page 89 Fuses (2/3) allocation of fuses in the passenger compartment (the presence of certain fuses dePends on the Vehicle eQuiPment leVel) 5.11...
- Page 90 Fuses (3/3) number allocation number allocation number allocation 22 and Empty Location Instrument panel- Empty location Automatic transmission Cluster,Fuel pump Relay, Injection Engine Control Roof Light Left-hand main beam Unit/Starter headlight Cluster Stop Light Switch, Radio/ Right-hand main beam Ultra Low cost Low Beam headlight Left-hand dipped beam...
-
Page 91: Radio Frequency Remote Control: Batteries
Contact Insert a minus screw driver into the Do not throw away your used approved Renault Dealer slit of the Decor shell and twist it to batteries; give them to an organisation replacement of the battery. separate the Decor shell from the lower responsible for collecting and recycling part. -
Page 92: Battery: Troubleshooting
Battery: troubleshooting (1/2) to avoid all risk of sparks: connecting a battery charger – Ensure that all electrical equipments the battery charger must be (courtesy lights, etc.) are switched off compatible with a battery with before disconnecting or reconnecting nominal voltage of 12 volts. the battery;... - Page 93 Battery: troubleshooting (2/2) starting the vehicle using the battery from another vehicle If you have to use the battery from another vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you already have jump leads, ensure that they are in perfect condition.
-
Page 94: Towing
toWing Front towing point 1. This towing point must only be used for towing: never use it for lifting the vehicle directly or indirectly. Do not remove the key from the ignition when the vehi- cle is being towed. When engine stopped, steering and braking as- sistance are not operational. -
Page 95: Accessories
accessories electrical and electronic accessories Before installing this type of accessory, make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 watts only. Fire hazard. No work may be carried out on the vehicle’s electrical or radio circuits, except by authorised dealers: an incorrectly connected system may result in damage being caused to the electrical equipment and/or the components connected to it. -
Page 96: Operating Faults
oPerating Faults (1/3) the following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. the starter is activated PossiBle causes What to do Warning lights dim or fail to come on; Battery terminals disconnected, Retighten them, reconnect them or clean the starter does not run. - Page 97 oPerating Faults (2/3) on the road PossiBle causes What to do Vibrations. Tyres not inflated to correct Check the tyre pressures; if this is not the cause, have pressures, incorrectly balanced or their condition checked by an approved dealer. damaged. Coolant boiling in the coolant Mechanical fault: cylinder head Stop the engine.
- Page 98 oPerating Faults (3/3) on the road PossiBle causes What to do The engine overheats. The coolant Engine cooling fan not working. Stop the vehicle,switch off the engine and temperature indicator light comes contact an approved dealer. Coolant leaks. Stop the vehicle, switch off the engine and check the coolant reservoir: it should contain fluid.
- Page 99 Section 6: Technical specifications Identification plates ............. . Engine specifications .
-
Page 100: Identification Plates
IDENTIFICATION PLATES Vehicle Identification Number The information shown on the vehicle identification plate should be quoted on all correspondence or orders. Open up the insulator to access the Vehicle Identification number Plate. Vehicle identification plate A : Identification number. -
Page 101: Engine Specifications
ENgINE SPECIFICATIONS Versions 0.8 12V 1.0 12V Engine type BR08DE BR10DE (see engine plate) Cubic capacity (cc) Petrol Type of fuel octane rating The use of unleaded petrol is essential, with the octane rating as stated on the label inside the fuel filler flap. -
Page 102: Dimensions
DIMENSIONS (in metres) 1.386 0.658 2.422 0.598 1.750 3.679 1.472 (*) 1.382 (*) unladen... -
Page 103: Replacement Parts And Repairs
rEPLACEMENT PArTS AND rEPAIrS Original parts are based on strict specifications and are subject to highly specialized tests. Therefore, they are of atleast the same level of quality as the parts fitted originally. If you fit genuine replacement parts always to your vehicle, it will perform well. Furthermore, repairs carried out within manufacturers network using original parts are guaranteed according to the conditions set out on the reverse of repair order. -
Page 104: Service Sheets
SErVICE ShEETS (1/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □... - Page 105 SErVICE ShEETS (2/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
- Page 106 SErVICE ShEETS (3/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
- Page 107 SErVICE ShEETS (4/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
- Page 108 SErVICE ShEETS (5/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
- Page 109 SErVICE ShEETS (6/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
-
Page 110: Anticorrosion Check
ANTICOrrOSION ChECk (1/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.12... - Page 111 ANTICOrrOSION ChECk (2/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.13...
- Page 112 ANTICOrrOSION ChECk (3/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.14...
- Page 113 ANTICOrrOSION ChECk (4/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.15...
- Page 114 ANTICOrrOSION ChECk (5/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.16...
- Page 115 ANTICOrrOSION ChECk (6/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
- Page 116 6.18...
- Page 117 AlphAbeticAl index (1/3) accessories................ 5.17 dashboard............... 1.21 – 1.22 accessories socket .............. 3.9 dimensions ................6.4 adjusting your driving position ..........1.8 doors................1.4 →1.6 air bag..............1.12 – 1.13 driving ........1.21 – 1.22, 2.2 – 2.4, 2.7 → 2.13 air conditioning ............3.4 → 3.6 air vents ..............
- Page 118 AlphAbeticAl index (2/3) fuel tank ..............1.33 – 1.34 lights .................. 1.28 fuses ..............5.10 → 5.12 lights: dipped beam headlights ..........1.28 main beam headlights ..........1.28 gear lever..............2.5 – 2.6 side lights ..............1.28 glove box ................3.9 locking the doors ..............
- Page 119 AlphAbeticAl index (3/3) remote control door locking unit .......... 1.4 replacement parts ..............6.5 vehicle identification plates ..........6.2 reverse gear ventilation selecting ...........2.5 – 2.6, 2.10 → 2.13 heating and air conditioning system .....3.4 →3.6 running in ................2.2 warning buzzer ..............
- Page 121 Section 8: Radio Introduction to controls..................................7.8 General Introduction..................................7.9 Auxillary audio function................................7.9 Hands-free function................................7.9 Radio (AM/FM)..................................7.9 Switch ON/OFF..................................7.10 Source selection..................................7.10 Volume/Mute..................................7.10 Listening to radio..................................7.10 Storage of radio stations................................7.10 Auxillary audio sources/services..............................7.11 Making/Receiving calls.................................7.12 Audio settings....................................7.12 Radio settings....................................7.13 Phone settings.....................................7.13 Bluetooth settings..................................7.13 Connecting to Bluetooth................................7.13...
- Page 123 radio guide(1/7) It is essential to follow the precautions in following pages when using the system, both in the interest of safety and to prevent material damage.User must always comply with laws of the country in which user are travelling.
- Page 124 radio guide(2/7) 1 Displays the artists of tracks / FM 10 Select the Required connected Precautions concerning tuned in / Preset station 1 for FM medium the equipment 2 Select previous folder from the 11 Answer a call Do not attempt to dismantle auxiliary storage/ Preset station 2 for 12 Select previous track or fast rewind or modify the system...
-
Page 125: Auxillary Audio Function
radio guide(3/7) introduction Hands-Free function Precautions concerning The audio system comprises of the The hands free Bluetooth system the equipment following functions: provides the following function without Do not attempt to dismantle having to handle user’s phone: - USB or modify the system - Receive a call as there is a risk of damage to - Bluetooth hands-free phone system... -
Page 126: Radio (Am/Fm)
radio guide(4/7) Switchin on and off Storage of radio stations User can Play or pause using the same button when radio is connected to Short Press 17 to switch on user’s This operating mode allows user to Auxiliary devices via. USB or AUX port radio system. - Page 127 radio guide(5/7) aF-rdS (radio data System) Each press of (preset1) button 1 in USB If this is the first connection will display the options File, Folder, automatic returning system, audio Artist, Album, Title and the last selected playback will begin with the The frequency of an FM station changes from the list shall display in the display first track from the folder...
-
Page 128: Audio Settings
radio guide(6/7) Making or receiving a call audio Settings It is recommended that The phone calls can be accessed from Radio gives access to settings for the user stop user’s vehicle user’s radio once it has been paired music user listen to, by short pressing before entering a number or with user device. -
Page 129: Radio Settings
radio guide(7/7) radio Settings Bluetooth Settings .user can activate or deactivate the Bluetooth function by pairing user’s The radio channels can be selected The bluetooth audio settings can be device with the radio system from a given bandwidth either by set by the user themselves. - Page 130 7.14...
Need help?
Do you have a question about the KWID and is the answer not in the manual?
Questions and answers
what is the warranty on what parts of my vehicle
The Renault Kwid comes with a standard 5-year/150,000 km mechanical warranty, covering the repair or replacement of defective parts due to material, assembly, or manufacturing defects acknowledged by the manufacturer. It also includes coverage for consequential damage resulting from the principal defect. Additionally, there is a 6-year anti-corrosion warranty for components with inherent paintwork defects.
This answer is automatically generated
Hi my OBD2 port doesn't have a power and my radio doesn't switch on what could be the problem.i **** driving Renault kwid 2021 model
The issue could be caused by a blown fuse, as both the OBD2 port and radio rely on the vehicle's electrical system. Check the fuse box for any blown fuses related to the multimedia system or power supply. Additionally, incorrect wiring or a disconnected power source could also lead to this problem. Ensure that no work has been done on the vehicle’s electrical system that may have caused a disconnection or short circuit. If the issue persists, consult an approved Renault dealer.
This answer is automatically generated