8BITDO SN30 Pro Instruction Manual

8Bitdo :
SN30ProandSF30Pro
Instruction Manual
• Press START to turn on the controller.
• Press and hold START for 3 seconds to turn off the controller.
• Press and hold START for 8 seconds to force turn off the controller.
© Bluetooth Connection
gB
Switch
1. Press START+Y to turn on the controller, LEDs will start to rotate from left to right.
2. Press and hold PAIR for 2 seconds to enter pairing mode. LEDs will turn off for a second then start to rotate from
left to right
3. Go to your Switch Home Page to click on Controllers, then click on Change Grip/Order and wait for controller to
sync up. LED will become solid when connection is successful.
4. Controller will auto reconnect to your Switch with the press of START once it has been paired
• STAR button = Switch screenshot button, Home button = Switch HOME button.
Android
1. Press START+B to turn on the controller, LED 1 will start to blink.
2. Press and hold PAIR for 3 seconds to enter pairing mode. LED will rotate from left to right.
3. Go to your Android device's Bluetooth setting, pair with [8Bltdo SF30 Pro] or [8Bitdo SN30 ProJ. LED will become
solid when connection is successful.
4. Controller will auto reconnect to your Android device with the press of START once it has been paired.
• USB Connection: connect the controller to your Android device via USB Cable after step 1.
EIBitdo"
S9
Windows
1. Press START+X to turn on the controller, LEDs 1,2 will start to blink.
2. Press and hold PAIR for 3 seconds to enter pairing mode. LEDs will rotate from left to right.
3. Go to your Windows device's 8luetooth setting, pair with [8Bitdo SF3O Pro] or [8Bitdo SN30 Pro). LED will become
solid when connection is successful.
4. Controller will auto reconnect to your Windows device with the press of START once it has been paired.
• USB Connection: connect the controller to your Windows device via USB Cable after step 1.
O
macOS
1. Press and hold START+A for 1 second to power on the controller, LEDs 1,2,3 will start to blink.
2. Press and hold PAIR for 3 seconds to enter pairing mode. LEDs will rotate from left to right
3. Go to your macOS device's Bluetooth setting, pair with [Wireless Controller!. LED will become solid when
connection is successful.
4. Controller will auto reconnect to your Windows device with the press of START once it has been paired.
• USB Connection: connect the controller to your macOS device via USB Cable after step 1.
Turbo function
1. Hold the button you would like to set turbo functionality to and then press the STAR button to activate turbo
functionality.
2. HOME LED will blink when turbo functionality has been applied successfully.
3. All buttons with Turbo functionality activated will cause the HOME LED to blink, showing you that Turbo
functionality is active on that button.
4. To deactivate turbo function, hold the button with turbo functionality activated press the STAR button to
deactivate turbo functionality. The HOME LED will no longer blink if you have successfully disabled turbo
functionality.
• Analog sticks are not included.
• This does not apply to Switch.
Low battery mode POWER LED blinks
@ Battery
Battery charging POWER LED stays solid
Battery-fully charged
POWER LED turns off
• Built-in 480 mAh Li-on withlô Hours of play time.
• Rechargeable via its USB-C cable with 1 - 2 hour charging time.
• Battery charging time might vary depending on the environment the controller Is exposed to.
0 Power Saving
1. Sleep mode -1 minute with no Bluetooth connection.
2. Sleep mode -15 minutes with Bluetooth connection but no use.
3. Press START to wake up your controller.
Ç? Support and firmware upgrade
• Please visit http://support.8bltdo.com for further information and additional support.