Related Manuals for Aquavolta H2-TURBO 2.0
Summary of Contents for Aquavolta H2-TURBO 2.0
- Page 1 -TURBO 2.0 Hydrogen-Booster 6th Generation MANUAL by Karl Heinz Asenbaum & Dipl. Eng. Yasin Akgün Version 2024/04/08...
- Page 2 It is not only used by doctors for therapy, it has also established itself because of its good taste as a modern day to day drink. Responsible for the antioxidant power of AquaVolta ® according to the current scientific view is the content of dissolved hydrogen, or dH2.
- Page 3 PEM cell, in which the electrolysis gases H and O are cleanly separated and only the hydrogen accumulates in the water. In addition, boosters such as the Aquavolta® -Turbo use pressure systems to dissolve as much H as possible in the water. In the 6th booster generation, it has now been possible to keep the gas bubbles so small that the efficiency of the booster has been significantly increased.
- Page 4 The thread directly on the H thanks to its long-lasting battery. Any drinking Turbo Generator has 30mm We have designed the AquaVolta® H2 - Turbo water Hydrogen Booster so that you don't have to rely Always fill plastic bottles on a single type of water. If you don't trust the...
- Page 5 5 – Device description / scope of delivery 4 x Extra-production bottle 240 ml made of Pressure equalization holes in Screw-in production bottle Tritan 240 ml made of Tritan the screw cap. Do not block! Exchange for defekt or Pressure vents clouded bottles Safety valve: Please perforate every 1-3...
- Page 6 6 – Operational preparation 1. Construction: The H2 Turbo Booster consists of the H2 generator, the production vessel and a lid. 2. Start preparation: Open the production jar and remove the orange silicone plug. Any residual water that serves to protect the membrane should be disposed of and the vessel should then be rinsed with clean water.
- Page 7 7 - General instructions for use ➢Do not operate the device unless you have read and ➢Do not place the device outdoors ➢Do not use the power adapter if it is damaged or the cable understood the operating instructions. ➢Before turning on the device, the water reservoir must has been kinked.
- Page 8 8 – Preparation for operation and charging 1. Place the appliance on a dry, flat surface. 2. Plug the USB-C connector of the power adapter into the socket. Before using it for the first time, the battery must be fully charged. 3.
- Page 9 Use with the going out and the bubble formation ceases. If you want to stop a running optional production, press the start button again for 3 seconds. Aquavolta® H2 • For the 40 min. special operation for filling the Aquavolta ®...
- Page 10 H2 Turbo Booster including the pressure piston approx. every 1 to 3 months. Aquavolta® H Technical data • Prepare cleaning solution: Dissolve 1 teaspoon of citric acid in Turbo water and pour this solution into the tritan container.
- Page 11 We are committed to providing you with advice and assistance to Aquavolta ® is a word mark protected by the German ensure a quick resolution to your concern. Patent and Trademark Office as well as by the EUIPO 1.
- Page 12 12 – FAQ (Frequently Asked Questions) 2. How do I store the H Turbo Booster when not in use? Daily use and short-term and long-term storage For daily use and shorter breaks in use, please note the following: • Less than a week: If you have a break in use for less than a week, the device can be stored empty and with the lid closed. •...
- Page 13 13 – FAQ (Frequently Asked Questions) 5. What should I do if the booster is leaking? 1. Typical Cause: Leak Verification • Locating the leak: First, determine where the leak occurs. Particular attention should be paid to the connection between the production vessel and the generator.
- Page 14 14 – FAQ (Frequently Asked Questions) 7. How and why do I clean the production tank and electrodes of the H2 Turbo Booster in case of limescale deposits? Regular cleaning is necessary to remove limescale deposits and maintain the optimal bladder performance of the device. Visible traces of limescale or decreasing bladder performance are signs that cleaning is required.
- Page 15 15 – FAQ (Frequently Asked Questions) 9. Why is the LED on the H Turbo Booster not lit? 1. Checking the battery: Check that the booster's battery is fully charged. When the battery runs out, connect the booster with the included USB-C cable to charge it. Wait for charging to finish, then check again to see if the LED is on. 2.
- Page 16 Exploded view of the electrolysis cell (PEM) Please note the serial number here for service queries. You will find this on the underside of your H2 generator. Your Serial Number:...
Need help?
Do you have a question about the H2-TURBO 2.0 and is the answer not in the manual?
Questions and answers