Horizon Fitness 5.0U - UPRIGHT BIKE Manual

UPRIGHT BIKE OPERATION

HOW TO MOVE THE UPRIGHT BIKE

Due to the weight of the Upright Bike, it is recommended that two people move it. While one person lifts the back of the Upright Bike, the second person firmly holds the handlebar and tips the Upright Bike forward until it rolls on the wheels. Carefully move the Upright Bike to the desired location and then lower it.
If the Upright Bike rocks on the floor after being set down, turn the leveling feet underneath the front or rear stabilizer until the rocking motion is eliminated.

To reduce the risk of injury, use extreme caution while moving the Upright Bike. Do not attempt to move it over uneven surfaces and make sure there's a clear space of 24 inches (minimum) on all sides of the equipment.

LOCATION OF THE UPRIGHT BIKE

Place the Upright Bike on a level surface. There should be 2 feet (60 cm) on each side surrounding the Upright Bike. Do not place the cycle in any area that will block any vent or air openings. The Upright Bike should not be located in a garage, covered patio, near water or outdoors.

HOW TO ADJUST THE UPRIGHT BIKE

The Upright Bike can be adjusted for maximum comfort and exercise effectiveness. The instructions below describe one approach to adjusting the Upright Bike to ensure optimal user comfort and ideal body positioning; you may choose to adjust the Upright Bike differently.

Do not adjust seat height past MAX mark on post.
Tighten knob "B" fully before use.

SEAT ADJUSTMENT
Proper seat height helps ensure maximum exercise efficiency and comfort, while reducing the risk of injury. Adjust the seat height to make sure it's in proper position, one that keeps a slight bend in your knee while your legs are in the extended position.

1. Seat Horizontal Position Rotate the seat adjustment knob counterclockwise to slide the seat forward or backward as desired. Rotate the knob clockwise to lock the position. Test the seat slide for proper operation.
2. Seat Height Turn the adjustment knob counterclockwise and adjust the seat to a comfortable pedaling position. Rotate the knob clockwise to lock seat position.
3. Pedal Straps Place the ball of the foot into the strap until it's centered over the pedal, reach down and pull the pedal strap up to tighten prior to use. To remove your foot from the strap, loosen the strap and pull out.

ASSEMBLY

There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the Upright Bike could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the Upright Bike, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your Upright Bike's serial number located on the front stabilizer of the cycle.

Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

MODEL INFORMATION

MAIN PARTS INCLUDED:

• Main Frame (20)
• Front Stabilizer (21F)
• Rear Stabilizer (21R)
• Handlebar Set (30)
• Mast Cover (26)
• Console (32)
• Console Mast (33)
• Pedal Set (37&39 L&R)
• Seat Post Set (10,11,35,36)
• Power Adapter

PARTS PACKING INCLUDED:

• 1 Hardware Kit
• 1 Owner's Manual

HARDWARE KIT:

PRE ASSEMBLY

UNPACKING

Due to the weight of the Upright Bike, it is recommended that two people perform the assembly. Unpack the product where you will be using it. It is recommended that you place a protective covering on your floor. Place the carton on a level flat surface and remove all packing materials; do not dispose of the packing materials until assembly is completed.
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.

ASSEMBLY

1. 
   HARDWARE:
   
   1. Open hardware for Step 1.
   2. Attach the Front Stabilizer (21F) and Rear Stabilizer (21R) to the Main Frame (20) using 4 Bolts (1), 4 Spring Washers (2) and 4 Flat Washers (3). Tighten firmly.
2. 
   HARDWARE:
   
   1. Attach Lead Wire (24) to Console Cable (23). Pull through Mast Cover(26) and out opening of Console Mast (33).
   2. Slide Mast Cover(26) over Console Mast (33).
   3. Attach Console Mast (33) to Main Frame (20) using 6 Bolts (4,5), 4 Nuts (6) and 10 Washers (3). Tighten firmly.

NOTE: Be careful not to pinch any wires while assembling console mast.

3. 
   HARDWARE:
   
   1. Open hardware for Step 3.
   2. Attach Lead Wire (24) to Handlebar cable (25) and feed Handlebar Cable (25) through the Console Mast (33).
   3. Attach Handlebar Set (30) to Console Mast (33) with 4 Bolts (4) and 4 Flat Washers (3).

NOTE: Be careful not to pinch any wires while assembling handlebars.

4. 
   HARDWARE:
   
   1. Open hardware for Step 4.
   2. Insert Plate (9) into Seat Slider (36).
   3. Place Seat (35) with Plate (9) onto seat post U-bracket and screw Seat Adjustment Knob (11) with Flat Washer (8) into Plate (9).
   4. Insert End Cap (10) onto Seat Slider (36).
5. 1. Identify Left Pedal (37L) which is labeled L on spindle and Right Pedal (37R) labeled R.
   2. Insert Left Pedal Strap (39L) into Left Pedal (37L) and Right Pedal Strap (39R) into Right Pedal (37R).
   3. Insert Left Pedal (37L) into Left Crank Arm (38L), ensure screw threads are aligned. Tighten Counter-clockwise.
   4. Insert Right Pedal (37R) into Right Crank Arm (38R), ensure screw threads are aligned. Tighten Clockwise.
   5. Use Wrench to fully tighten pedals. No screw threads should be visible and pedal axle should be fully seated.

NOTE: Make sure pedals are FULLY TIGHTENED before use.
NOTE: Left crank arm is reverse threaded so it is very important to tighten counter-clockwise. Tightening the opposite direction can damage pedal or crank arm.

6. 
   HARDWARE:
   
   1. Open hardware for Step 6.
   2. Attach Console Cable (23), Handlebar Cables (25), and Fan Cable (27) to Console (32).
   3. Carefully tuck all cables into Console Mast (33).
   4. Attach Console (32) to Console Mast (33) using 4 Bolts (7).

NOTE: Be careful not to pinch any wires while assembling console.

7. CONGRATULATIONS!
   You have successfully assembled your Upright Bike.

CONSOLE OPERATION

5.0U CONSOLE

NOTE: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.

5.0U CONSOLE OPERATION

LCD DISPLAY WINDOWS: time, remain, distance, calories, heart rate, timer, speed, watts, cadence and resistance level.
LCD DISPLAY INDICATORS: indicates what information is being displayed.
START: press to begin exercising, start your workout, or resume exercising after pause.
STOP: press to pause/end your workout. Hold for 3 seconds to reset the console.
SPLIT: press this key to reset the Segment Time count-up timer to 0 seconds.
UP/DOWN KEYS: used to adjust resistance level.
QUICK KEYS: used to instantly jump to the desired resistance level.
DISPLAY/ENTER: used to confirm a selection. Press to change display feedback during workout.
BLUETOOTH: used to connect bluetooth devices. hold to switch between Heart Rate mode and App mode.
ENERGY SAVER: To minimize energy consumption, your machine will enter energy saver mode (ERP) automatically when not in use and the console will be woken up quickly with a touch of a button.
USB PORT: for charging and software updates, maximum output is 1A/5V.

5.0U CONSOLE DISPLAY

TIME/REMAIN: Shown as minutes: seconds. View the time remaining or the time elapsed in your workout.
HEART RATE: Shown as BPM (beats per minute). Used to monitor your heart rate (displayed when using HR straps).
DISTANCE: Shown as miles. Indicates distance traveled or distance remaining during your workout.
WATTS: Indicates your cycling rate at any moment.
CALORIES: Total calories burned or calories remaining left to burn during your workout.
TIMER: is almost identical to TIME, but will reset to 0s when the split key is pressed.
SPEED: Shown as MPH. Indicate the bike's overall speed on the road.
RESISTANCE: Shows the current level of resistance.
CADENCE: Shown as RPM. Indicates how fast the foot pedals are moving.

PROGRAM INFORMATION

P1) MANUAL: Adjust your resistance manually during your workout.
P2) DISTANCE: Push yourself and go further during your workout with 13 distance workouts. Choose from 1 mile, 2 miles, 5k, 5 miles, 10k, 8 miles, 15k, 10 miles, 20k, half marathon, 15 miles, 20 miles, and marathon goals.
P3) CALORIES: Set goals for burning calories.
P4) FAT BURN: A workout designed specifically to target fat. Promotes weight loss by increasing and decreasing the resistance, while keeping you in your fat burning zone. Includes 10 levels.
P5) INTERVALS: Improves your strength, speed, and endurance by increasing and decreasing the resistance throughout your workout to involve your heart and other muscles. Includes 10 levels.

GETTING STARTED

1. Check to make sure no objects are nearby that will hinder the movement of the Bike.
2. Plug in the power cord.

NOTE: The Bike does not have a power switch and will turn on when power is supplied.

QUICK START UP
Simply press the START key to begin working out. The time will count up from 0:00, the resistance level will default to level 0. OR...

SELECT A WORKOUT OR TARGET

1. Select your PROGRAM with the Up/Down buttons and press ENTER when your desired PROGRAM is displayed.
2. Adjust the SETTING with the Up/Down buttons and press ENTER when your desired SETTING is displayed.
3. Press START to begin.

NOTE: If no WORKOUT is selected, the program will function as a MANUAL program. All changes in resistance level will need to be from the user in this setting.

TO RESET THE CONSOLE
Hold STOP key for 3 seconds.

FINISHING YOUR WORKOUT
When your workout is complete, the monitor display will beep. Your workout information will stay displayed on the console for 30 seconds and then reset.

CLEAR CURRENT SELECTION
To clear the current program selection or screen, hold the STOP button for 3 seconds.

HOW TO SWITCH BETWEEN APP MODE & BT HEART RATE MODE

HORIZON CONNECTED FITNESS SYSTEM

Your Horizon machine is Bluetooth ready, allowing you to use Bluetooth 4.0 technology to wirelessly connect your device and other apps to your Horizon product. For a complete list of 3rd party fitness apps compatible with your Horizon product follow the link below:
http://horizonfit.co/5-0U

TROUBLESHOOTING

COMMON PRODUCT QUESTIONS

ARE THE SOUNDS MY Upright Bike MAKES NORMAL?
Our Upright Bikes are some of the quietest available because they use belt drives and magnetic brake resistance. We use the highest grade bearings and chains/belts to minimize noise. However, because the resistance system itself is so quiet, you will occasionally hear other slight mechanical noises. Unlike older, louder technologies, there are no fans, friction belts, or alternator noises to mask these sounds on our Upright Bikes. These mechanical noises, which may or may not be intermittent, are normal and are caused by the transfer of significant amounts of energy to a rapidly spinning flywheel. All bearings, chains/belts and other rotating parts will generate some noise which will transmit through the casing and frame. It is also normal for these sounds to change slightly during a workout and over time because of thermal expansion of the parts.

WHY IS THE Upright Bike I HAD DELIVERED LOUDER THAN THE ONE AT THE STORE?
All fitness products seem quieter in a large store showroom because there is generally more background noise than in your home. Also, there will be less reverberation on a carpeted concrete floor than on a wood overlay floor. Sometimes a heavy rubber mat will help reduce reverberation through the floor. If a fitness product is placed close to a wall, there will be more reflected noise.

HOW LONG WILL THE BELT LAST?
The computer modeling we have done indicated virtually thousands of maintenance free hours. You should not have to replace the belt as long as you have the Upright Bike.

CAN I MOVE THE Upright Bike EASILY ONCE IT IS ASSEMBLED?
Your Upright Bike has a pair of transport wheels built into the front stabilizer tube. Please follow the moving the Upright Bike section to transport your Upright Bike. It is important that you place your Upright Bike in a comfortable and inviting room. Your Upright Bike is designed to use minimal floor space. Many people will place their Upright Bikes facing the TV or a window. If at all possible, avoid putting your Upright Bike in an unfinished basement. To make exercise a desirable daily activity for you, the Upright Bike should be in a comfortable setting.

TROUBLE SHOOTING

PROBLEM: The Upright Bike makes a squeaking or chirping noise.
SOLUTION: Verify the following:

• The Upright Bike is on a level surface.
• Loosen all bolts attached during the assembly process, grease the threads, and tighten again.

If this does not remedy the problem, you may CONTACT CUSTOMER TECH SUPPORT AT THE NUMBER ON THE BACK PANEL.
The following information may be asked of you when you call. Please have these items readily available:

• Model Name
• Serial Number
• Proof of Purchase (receipt or credit card statement)

You may find more troubleshooting suggestions on the customer support section of our website. Contact customer support using the contact information on the BACK PANEL.
In order for Customer Tech Support to service your Upright Bike they may need to ask detailed questions about the symptoms that are occurring. Some troubleshooting questions that may be asked are:

• How long has this problem been occurring?
• Does this problem occur with every use? With every user?
• If you are hearing a noise, does it come from the front or the back? What kind of noise is it (thumping, grinding, squeaking, chirping etc.)?
• Has the machine been lubricated and maintained per the maintenance schedule?

Answering these and other questions will give the technicians the ability to send proper replacement parts and the service necessary to get you and your Upright Bike running again!

MAINTENANCE

What kind of routine maintenance is required?
Minimal maintenance and cleaning is required. We use sealed bearings throughout our bikes so lubrication is not needed. The most important maintenance step is to simply wipe your perspiration off the bike after each use.

How do I clean my bike?
Clean with mild soap and water cleaners only. Never use solvents on plastic parts. Cleanliness of your bike and its operating environment will keep maintenance problems and service calls to a minimum. For this reason, we recommend that the following preventive maintenance schedule be followed.

MAINTENANCE SCHEDULE

AFTER EACH USE
Clean the Upright Bike using soft cloths or paper towels or other gentle solution (cleaning agents should be alcohol and ammonia free). Disinfect the saddle and handlebars and wipe off all bodily residues.

BEFORE EACH USE
Make sure that the Upright Bike is level and does not rock. Ensure that the pedals are tight in crank arms and not crossthreaded, all screws on pedals are tight, and pedal straps are not frayed.

MONTHLY
Inspect all assembly bolts and pedals on the machine for proper tightness.
Adhering to this schedule will extend the life of your machine.

READ AND SAVE ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EXERCISE BIKE. IT IS STRONGLY RECOMMENDED TO TAKE THE FOLLOWING SAFETY INSTRUCTIONS.

• 
  If you experience chest pains, nausea, dizziness or shortness of breath, stop exercising immediately and consult your physician before continuing.
• Use this exercise bike for its intended purpose as described in this manual. Do not use attachments that have not been recommended by the manufacturer.
• Never operate the exercise bike if it is not working properly, or if it has been damaged. Contact Customer Tech Support or the authorized dealers for examination and repair.
• Do not use the exercise bike without proper footwear. NEVER operate the exercise bike with bare feet.
• Do not wear any clothing that might catch on any moving parts of this exercise bike.
• Keep hands and feet clear at all times from moving parts to avoid injury. Never turn the pedal cranks by hand.
• Do not dismount the exercise bike until the pedals are at a complete STOP.
• Do not attempt to ride the exercise bike in a standing position at high RPMs until you have practiced at slower speeds.
• Do not insert any object, hands or feet into any openings, or expose hands, arms or feet to the drive mechanism or other potentially moving part of the exercise bike.
• Do not use any equipment that is damaged or has worn or broken parts. Use only replacement parts supplied by Customer Tech Support or the authorized dealers.
• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.
• Close supervision is necessary when used near children, invalids or disabled people.
• When the exercise bike is in use, young children and pets should be kept at least 3 meters / 10 feet away.
• Ensure that seat adjustment knobs (seat and handlebar fore-and-aft) are properly secured and do not interfere with range of motion during exercise.