Sealey SSG401.V3 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instruction protection
manual
1. SAFETY
Familiarise yourself with the application and limitations, as well as the potential hazards of the spray gun.
9
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
‰
equipment.
WARNING! Disconnect the spray gun from the air supply before changing accessories, servicing or performing any maintenance.
‰
Maintain the spray gun in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the
9
warranty.
Locate the spray gun in a suitable work area, keep area clean and tidy and free from unrelated materials, ensuring that there is
9
adequate ventilation and lighting.
Keep the spray gun clean for best and safest performance.
9
Ensure the air system has sufficient output for the spray gun air consumption (see specification).
9
WARNING! Wear approved safety eye protection (standard spectacles are not adequate).
‰
Wear approved respiratory protection, safety eye goggles and skin protection.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and tie back long hair.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
When gun is not in use ensure the air supply is disconnected.
9
Avoid unintentional operation.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
DO NOT paint were there is any source, or possible source, of ignition as paint mist is extremely flammable.
8
DO NOT point spray gun at yourself or at other persons or animals.
8
DO NOT carry by the air hose, or yank the hose from the air supply.
8
DO NOT use the spray gun for any purpose other than for which it is designed.
8
DO NOT allow untrained persons to operate the spray gun.
8
DO NOT get the spray gun wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT operate gun if any parts are missing or damaged as this may cause failure and/or personal injury.
8
DO NOT direct air from the air hose at yourself or others.
8
2. INTRODUCTION
Ideal for applying base coats. Features adjustable paint flow and fan width controls. Supplied with aluminium cam-action suction feed
pot. Suitable for use with water-based paints. Alternative set-ups available separately.
3. SPECIFICATION
Model No: .................................................. SSG401.V3
Air consumption: .............................................. 5-11cfm
Available set-ups: ....................... 1.2,1.8,2.0,2.2,2.5mm
Pot capacity: ..................................................... 1000ml
Recommended air pressure: ................................ 50psi
4. AIR SUPPLY CONNECTION
4.1. For recommended hook-up, see diagram (fig.1).
4.2. Ensure the trigger is in the "off" position before connecting to the air supply.
4.3.
You will require an air supply capable of providing a pressure 50psi and an air volume of 11cfm to operate the gun.
‰
WARNING! Ensure the air supply is clean and is regulated to a maximum of 50psi. Too high an air pressure and unclean
air will shorten the life of the gun due to excessive wear and may be dangerous, causing damage and/or personal injury.
4.4. Drain the air supply tank and pressure regulator daily. Water in the air line will damage the gun and contaminate the paint.
4.5. Clean the compressor air inlet filter weekly.
4.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
10mm (3/8") I.D. and fittings must have the same inside dimensions.
© Jack Sealey Limited
GENERAL-PURPOSE SUCTION FEED SPRAY
GUN 1.5MM SET-UP
MODEL NO:
Wear
Wear
protective
respiratory
clothing
protection
Original Language Version
SSG401.V3
Wear
protective
gloves
SSG401.V3 Issue:1 03/11/22