Sealey SSG1.V2 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction Wear eye
manual protection
1. SAFETY
Familiarise yourself with the application and limitations, as well as the potential hazards of the spray gun.

WARNING! Disconnect the spray gun from the air supply before changing accessories, servicing or performing any maintenance.

Maintain the spray gun in good condition (use an authorised service agent).

Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the

warranty.
Locate the spray gun in a suitable work area, keep area clean and tidy and free from unrelated materials, and ensure that there is

adequate ventilation and lighting.
Keep the spray gun clean for best and safest performance.

Ensure the air system has sufficient output for the spray gun air consumption (see specification).

Wear approved respiratory protection, safety eye goggles and skin protection.

Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and tie back long hair.

Keep children and unauthorised persons away from the work area.

When gun is not in use ensure the air supply is disconnected.

Avoid unintentional operation.

DO NOT paint were there is any source, or possible source, of ignition as paint mist is extremely flammable.

DO NOT point spray gun at yourself or at other persons or animals.

DO NOT carry the by the air hose, or yank the hose from the air supply.

DO NOT use the spray gun for any purpose other than for which it is designed.

DO NOT allow untrained persons to operate the spray gun.

DO NOT get the spray gun wet or use in damp or wet locations or areas where there is condensation.

DO NOT operate gun if any parts are missing or damaged as this may cause failure and/or personal injury.

DO NOT direct air from the air hose at yourself or others.

When not in use switch the spray gun off and disconnect from the air supply.

2. INTRODUCTION
Superbly balanced spray gun suitable for applying finishing coats. Supplied with cam action suction pot and fitted with air regulator control.
Suitable for use with water based paints. Alternative set-up available separately.
3. SPECIFICATION
Model no: ..........................................................................................................SSG1.V2
Standard set up: .....................................................................................................1.8mm
Available set up: ........................................................................................................2mm
Pot capacity: ...........................................................................................................900ml
Recommended air pressure: ...............................................................................30-70psi
Air consumption: ..................................................................................................7-12cfm
Weight: ...................................................................................................................1.12kg
4. AIR SUPPLY
4.1. Ensure the air valve is in the "off" position before connecting to the air supply.
4.2. You will require an air pressure of approximately 70psi and an air volume of 12cfm to operate the gun.
4.3.  WARNING: Ensure the air supply is clean does not exceed 90psi. Too high an air pressure and unclean air will shorten the
life of the gun due to excessive wear and may be dangerous, causing damage and/or personal injury.
4.4. Drain the air supply tank daily. Water in the air line will damage the gun and contaminate the paint.
4.5. Clean the compressor air inlet filter weekly. For recommended
hook-up, see diagram.
4.6. Line pressure should be increased to compensate for unusually
long air hoses (over 8 metres). The minimum hose diameter
should be 0mm I.D. and fittings must have the same dimensions.
4.7. Keep hose away from heat, oil and sharp edges.
4.8. Check hoses for wear, and make certain that all connections
are secure.
© Jack Sealey Limited
SPRAY GUN SUCTION DELUXE
PROFESSIONAL 1.8MM SET-UP
SSG1.V2
MODEL No:
Wear a Wear protective
mask clothing
Original Language Version
SSG1.V2 Issue:3 (HF) - 26/11/18