Table of Contents
Advertisement
P
T
RAV200 R
ROGRAMMING
HE
S
U
Y
C
B
ETTING
P
OUR
ABLE
OX
1. Turn on the cable box (or DSS) and look up a setup
code for your brand of cable box (or DSS) – see pages
114 and 115 of the HTR-5140 Owner's Manual.
2. On the RAV200, press CBL/DBS.
3. Press and hold both VOLUME buttons at least four
seconds until the indicator LED flashes twice.
4. Using the keypad, enter the four-digit setup code.
The indicator LED will flash twice after your entry.
If the LED did not flash twice, repeat steps 3 and 4.
5. To verify the code works, aim the RAV200 at the
cable box (or DSS), press CBL/DBS, and then press
POWER. The unit should turn off. If it doesn't
respond, use another code for the same manufac-
turer and repeat steps 3 through 5.
S
U
Y
VCR
ETTING
P
OUR
1. Turn on the VCR and look up a setup code for your
brand of VCR (see pages 115 and 116 of the HTR-
5140 Owner's Manual).
2. On the RAV200, press VCR.
3. Press and hold both VOLUME buttons at least four
seconds until the indicator LED flashes twice.
4. Using the keypad, enter the four-digit setup code.
The indicator LED will flash twice after your entry.
If the LED did not flash twice, repeat steps 3 and 4.
5. To verify the code works, aim the RAV200 at the
VCR, press VCR, and then press POWER. The VCR
should turn off. If it doesn't respond, use another
code for the same manufacturer and repeat steps 3
through 5.
C
EMOTE
ONTROL
(
DSS)
OR
YHT-22 Q
U I C K
(C
)
ONTINUED
S
U
Y
DVD (
LD) P
ETTING
P
OUR
OR
1. Turn on the DVD (or LD) player and look up a
setup code for your brand of DVD (or LD) player
(see page 116 of the HTR-5140 Owner's Manual).
2. On the RAV200, press DVD/LD.
3. Press and hold both VOLUME buttons at least four
seconds until the indicator LED flashes twice.
4. Using the keypad, enter the four-digit setup code.
The indicator LED will flash twice after your entry.
If the LED did not flash twice, repeat steps 3 and 4.
5. To verify the code works, aim the RAV200 at the
DVD (or LD) player, press DVD/LD, and then press
POWER. The unit should turn off. If it doesn't
respond, use another code for the same manufac-
turer and repeat steps 3 through 5.
S
U
O
C
ETTING
P
THER
OMPONENTS
1. Turn on the component (e.g., CD player, tape deck,
or MD player) and look up a setup code for your
brand of component (see pages 113 through 117 of
the HTR-5140 Owner's Manual).
2. On the RAV200, press the desired component
button (e.g., CD or TAPE/MD).
3. Press and hold both VOLUME buttons at least four
seconds until the indicator LED flashes twice.
4. Using the keypad, enter the four-digit setup code.
The indicator LED will flash twice after your entry.
If the LED did not flash twice, repeat steps 3 and 4.
5. To verify the code works, aim the RAV200 at the
component, press the appropiate component button,
and then press POWER. The unit should turn off. If
it doesn't respond, use another code for the same
manufacturer and repeat steps 3 through 5.
-C
G
O N N E CT
U I D E
LAYER
11
Advertisement
Table of Contents
