Philips S3608 Quick Start Manual

English
Introduction
Congratulations on your purchase and welcome
to Philips! To fully benefit from the support
that Philips offers, register your product at
www.philips.com/welcome.
Important safety information
Only use the product for its intended purpose. Read
this important information carefully before you use
the product and its batteries and accessories, and save
it for future reference. Misuse can lead to hazards or
serious injuries.
Warning
Keep the supply unit dry (Fig. 2).
-
This shaver is waterproof (Fig. 3). It is suitable
-
for use in the bath or shower and for cleaning
under the tap. For safety reasons, the shaver can
therefore only be used without cord.
Do not modify the supply unit.
-
This appliance can be used by children aged from
-
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge if they have been
given supervision or instruction concerning use of
the appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.
Unplug the appliance before cleaning it with
-
water.
Do not use a damaged appliance. Replace
-
damaged parts with new Philips parts.
Do not use the supply unit in or near wall sockets
-
that contain an electric air freshener to prevent
irreparable damage to the supply unit.
Because of hygiene, only one person should use
-
the appliance.
Only use cold or lukewarm water to clean the
-
appliance.
Never use compressed air, scouring pads, abrasive
-
cleaning agents or aggressive liquids to clean the
appliance.
Water may drip from the socket at the bottom of
-
the shaver when you rinse it. This is normal and
not dangerous because all electronics are enclosed
in a sealed power unit inside the shaver.
Only use original Philips accessories or
-
consumables. Only use detachable supply unit
HQ8505.
Charge, use and store the product at a
-
temperature between 10 °C and 35 °C.
Keep product and batteries away from fire and
-
do not expose them to direct sunlight or high
temperatures.
If the product becomes abnormally hot or smelly,
-
changes color or if charging takes longer than
usual, stop using and charging the product and
contact Philips.
Do not place products and their batteries in
-
microwave ovens or on induction cookers.
Do not open, modify, pierce, damage or dismantle
-
the product or battery to prevent batteries
from heating up or releasing toxic or hazardous
substances. Do not short-circuit, overcharge or
reverse charge batteries.
If batteries are damaged or leaking, avoid contact
-
with the skin or eyes. If this occurs, immediately
rinse well with water and seek medical care.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable
standards and regulations regarding exposure to
electromagnetic fields.
General description (Fig. 1)
1 Protection cap
2 Shaving unit
3 Shaving unit release button
4 Charging lights
5 On/off button
6 Socket for small plug
7 Supply unit
8 Small plug
Charge indications
Battery low
When the battery is almost empty (when there are
only 5 or fewer shaving minutes left), the bottom
charging light starts to flash orange (Fig. 4).
When you switch off the shaver, the bottom charging
light continues to flash orange for a few seconds.
Charging
While the shaver charges, first the bottom charging
light flashes and then lights up continuously. Next
the second charging light flashes and then lights
up continuously, and so on until the shaver is fully
charged.
Battery fully charged
When the battery is fully charged, all charging lights
light up white continuously.
Note: After approx. 30 minutes, the charging lights go
out to save energy.
Quick charge
When the shaver is in quick charge mode, the
charging lights light up one after the other. After
approx. 5 minutes, the bottom charging light flashes
white (Fig. 4). The shaver now contains enough
energy for a 5-minute shave.
Charging
Charge the appliance at least 3 hours before first use
to achieve the best battery performance.
When you charge the appliance for the first time or
after a long period of disuse, let it get fully charged.
Charging takes approx. 1 hour.
-
Quick charge: After approx. 5 minutes of charging,
-
the battery contains enough energy for a 5-minute
shave.
When the appliance is fully charged, it has a
-
cordless operating time of up to 40 minutes.
Note: You cannot use the appliance while it is
charging.
Charging with the supply unit
1 Make sure that the appliance is switched off.
2 Put the small plug in the appliance and put the
supply unit in the wall socket (Fig. 5).
3 The charging light shows the charging status of
the appliance (see 'Charge indications').
4 After charging, remove the supply unit from the
wall socket and pull the small plug out of the
appliance.
Using the appliance
Warning: Always check the appliance and
all accessories before use. Do not use the
appliance or any accessory if it is damaged,
as this may cause injury. Always replace a
damaged part with one of the original type.
Note: This appliance is waterproof (Fig. 3). It is
suitable for use in the bath or shower and for cleaning
under the tap. For safety reasons, the appliance can
therefore only be used without cord.
Switching the appliance on and off
To switch the appliance on or off, press the on/off
button once (Fig. 6).
Shaving
For the best results on skin comfort, pre-trim your
beard if you have not shaved for 3 days or longer.
You can use this appliance either wet or dry, or even
under the shower. For a wet shave, apply some water
and shaving foam or gel to your skin and rinse the
shaving heads under the tap with warm water before
following the steps below.
1 Switch on the appliance (Fig. 6).
2 Move the shaver in circular movements over your
skin to catch hair growing in all directions (Fig. 7).
Make sure each shaving head is fully in contact
with the skin. Exert gentle pressure for a close,
comfortable shave.
Note: Do not press too hard, as this can cause skin
irritation.
Note: If you are shaving with gel or foam, rinse the
shaving unit regularly during your shave to ensure
that it continues to glide smoothly over your skin
(Fig. 8).
3 Use the narrow sides of the shaving unit to shave
in hard-to-reach areas such as along your jawline
and under your nose (Fig. 9).
4 Switch off and clean the appliance after each use
(see 'Cleaning and maintenance').
5 Put the protection cap on the shaver after use
to prevent damage and dirt accumulation in the
shaving heads.
Note: Make sure you rinse all foam or shaving gel off
the appliance.
Skin adaptation period
Your first shaves may not bring you the result you
expect and your skin may even become slightly
irritated. This is normal. Your skin and beard need
time to adapt to any new shaving system. To allow
your skin to adapt to this new appliance, we advise
you to shave regularly (at least 3 times a week) and
exclusively with this appliance for a period of 3 weeks.
Cleaning and maintenance
Cleaning the shaver
Clean the shaver after every shave for optimal shaving
performance.
Caution: While rinsing shaving heads, water
may drip out of the base of shaver. This is a
normal occurrence. Internal electric parts are in
a waterproof compartment so the shaver will be
protected against water damage.
1 Switch off the appliance and make sure it is
disconnected from the wall socket.
2 Press the shaving unit release button to open the
shaving unit (Fig. 10).
3 Rinse the shaving unit and hair chamber with
lukewarm water (Fig. 11).
4 Rinse the outside of the shaving unit with
lukewarm water.
5 Carefully shake off excess water and let air dry
completely.
Caution: Never dry the shaving unit with a
towel or tissue, as this may damage the shaving
heads.
6 Close the shaving unit (Fig. 12).
Thorough cleaning
Clean the shaving heads thoroughly once a month for
optimal performance.
1 Switch off the appliance and make sure it is
disconnected from the wall socket.
2 Press the shaving unit release button to open the
shaving unit (Fig. 10).
3 Pull the shaving unit off the appliance (Fig. 13).
4 Turn the locks counterclockwise (1) and remove
the retaining frames (2). Place them aside in a safe
place (Fig. 14).
5 Remove and clean one shaving head at a time.
Each shaving head consists of a cutter and a guard
(Fig. 15).
Note: Do not clean more than one cutter and
guard at a time, since they are all matching sets.
If you accidentally mix up the cutters and guards,
it may take several weeks before optimal shaving
performance is restored.
6 Remove the cutter from the shaving guard and
clean both parts under the tap (Fig. 16).
7 Put the cutter back into the guard (Fig. 17).
8 Put the shaving heads back into the shaving unit
(Fig. 18).
Note: Make sure that the shaving heads with
the projections fit exactly onto the hooks of the
shaving head holder when placing them (Fig. 19).
The shaving heads supplied with the shaver either
have notches or projections. Both shaving systems
are the same.
9 Put the retaining frames back into the shaving unit
(1) and turn the locks clockwise (2) (Fig. 20).
10 Insert the lug of the shaving unit into the slot in
the top of the appliance (Fig. 21).
11 Close the shaving unit (Fig. 12).
Note: If the shaving unit does not close smoothly,
check if you have inserted the shaving heads
properly and if the retaining frames are locked
properly.
Replacement
Replacing the shaving heads
For maximum shaving performance, we advise
you to replace the shaving heads every two
years (Fig. 22). Replace damaged shaving heads
immediately. Always replace the shaving heads
with original Philips shaving heads (see 'Ordering
accessories').
1 Switch off the appliance and make sure it is
disconnected from the wall socket.
2 Press the shaving unit release button to open the
shaving unit (Fig. 10).
3 Pull the shaving unit off the appliance (Fig. 13).
4 Turn the locks counterclockwise (1) and remove
the retaining frames (2). Place them aside in a safe
place (Fig. 14).
5 Remove the shaving heads from the shaving unit.
Discard the used shaving heads immediately to
avoid mixing them with the new shaving heads
(Fig. 23).
6 Place new shaving heads in the shaving unit
(Fig. 18).
Note: Make sure that the shaving heads with
the projections fit exactly onto the hooks of the
shaving head holder when placing them (Fig. 19).
The shaving heads supplied with the shaver either
have notches or projections. Both shaving systems
are the same.
7 Put the retaining frames back into the shaving unit
(1) and turn the locks clockwise (2) (Fig. 20).
8 Insert the lug of the shaving unit into the slot in
the top of the appliance (Fig. 21).
9 Close the shaving unit (Fig. 12).
Note: If the shaving unit does not close smoothly,
check if you have inserted the shaving heads
properly and if the retaining frames are locked
properly.
Storage
Put the protection cap on the shaver to prevent
damage.
Note: Always let the shaver dry completely before
storing.
Ordering accessories
To buy accessories or spare parts, visit
www.philips.com/parts-and-accessories or go to
your Philips dealer. You can also contact the Philips
Consumer Care Center in your country (see the
international warranty leaflet for contact details).
The following accessory is available:
SH30 replacement Philips shaving heads
-
Note: The availability of the accessories may differ by
country.
Support
For all product support such as frequently asked
questions, please visit www.philips.com/support.
Recycling
This symbol means that electrical products and
-
batteries shall not be disposed of with normal
household waste (Fig. 24).
Follow your country's rules for the separate
-
collection of electrical products and batteries.
Removal of built-in rechargeable battery
The built-in rechargeable battery must only be
removed by a qualified professional when the
appliance is discarded. Before removing the battery,
make sure that the appliance is disconnected from the
wall socket and that the battery is completely empty.
Take any necessary safety precautions when
you handle tools to open the appliance and
when you dispose of the rechargeable battery.
When you handle batteries, make sure that
your hands, the product and the batteries are
dry.
To avoid accidental short-circuiting of batteries
after removal, do not let battery terminals
come into contact with metal objects (e.g.
coins, hairpins, rings). Do not wrap batteries in
aluminum foil. Tape battery terminals or put
batteries in a plastic bag before you discard
them.
1 Check if there are screws in the back or front of the
appliance. If so, remove them.
2 Remove the back and/or front panel of the
appliance with a screwdriver. If necessary, also
remove additional screws and/or parts until you
see the printed circuit board with the rechargeable
battery.
3 Remove the rechargeable battery.
Bahasa Indonesia
Pendahuluan
Selamat atas pembelian Anda dan selamat datang di
Philips! Untuk memanfaatkan sepenuhnya dukungan
yang ditawarkan Philips, daftarkan produk Anda di
www.philips.com/welcome.
Informasi keselamatan penting
Hanya gunakan produk sesuai indikasi penggunaan.
Baca informasi penting ini dengan saksama sebelum
menggunakan produk, baterai, dan aksesorinya,
dan simpan untuk referensi di kemudian hari.
Penyalahgunaan dapat menyebabkan bahaya atau
cedera serius.
Peringatan
Usahakan unit catu daya tetap kering (Gbr. 2).
-
Alat cukur ini kedap air (Gbr. 3). Alat ini cocok
-
untuk digunakan di bak mandi atau shower
dan untuk membersihkan di bawah keran.
Untuk keamanan, alat cukur ini hanya dapat
dioperasikan tanpa kabel.
S3608