Advertisement
Technical Support and E-Warranty Certificate www.vevor.com/support
ICE-MAKING MACHINE
INSTALLATION MAINTENANCE
INSTRUCTIONS
MODEL:LB360TA/LB400TA/LB440TA/LB550TA
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the major
top brands and doses not necessarily mean to cover all categories of tools offered by us. You
are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.
Advertisement
Table of Contents
Related Manuals for VEVOR LB360TA
Summary of Contents for VEVOR LB360TA
- Page 1 Technical Support and E-Warranty Certificate www.vevor.com/support ICE-MAKING MACHINE INSTALLATION MAINTENANCE INSTRUCTIONS MODEL:LB360TA/LB400TA/LB440TA/LB550TA We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us.
- Page 2 This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
-
Page 3: Safety Precaution
SAFETY PRECAUTION Before the appliance is used, please read the manual carefully. To reduce the risk of fire, electrical shock or injury when using the appliance, follow basic precaution, including the following: DANGER: Read all instructions before using the ice-making machine. ... - Page 4 not in the vicinity of ice-making machine. Before you throw away your old ice-making machine, take off the door but leave the shelves in place so that children may not easily climb inside. Never allow children to operate, play with, or crawl inside the appliance. ...
- Page 5 This appliance contains a small quantity of R290/R600a ice-making machine which is environmentally friendly, but flammable. It does not damage the ozone layer, nor does it increase the greenhouse effect. During transportation and installation, ensure that the tubing of the refrigerant ...
- Page 6 compressor. Please be far away fire source during using, service and disposal. Note: Please keep the water or other conductive liquids away from the machine; Don’t stick clubs into the machine; During the movement of the machine, it should be carefully carried at an ...
-
Page 7: Basic Parameter
BASIC PARAMETER Model LB360TA LB400TA LB440TA LB550TA Power 700W 800W 1000W 1000W Max ice production ≥360 ≥400 ≥440 ≥500 capacity Number of ice 12*13=156 12*13=156 13*14=182 13*14=182 cells Input AC115V 60Hz Ice size 22*22*22mm Ice storage Theoretical ice storage: 150Kg;... -
Page 8: Basic Structure
LB360TA 1570 LB400TA 1570 LB440TA 1570 LB550TA 1570 BASIC STRUCTURE Split type Name Name Top panel Ventilation window Water pump Water supply valve Water level sensor Condenser Front panel Fan motor Control panel Compressor Evaporator Deicing solenoid valve Right panel... -
Page 9: Installation
INSTALLATION Open the case, move the machine to a appropriate location. Check the packing list and the contents, if they are different, please inquire your dealer. 2. Operating environment A. Environment temperature：SN、N：10℃～38℃ Environment humidity: relative humidity ≤90% - 8 -... - Page 10 The distance between the air outlets and the wall should be over 20 cm. Besides, keep good ventilation and ensure the machine is dry and clean. The position to place the ice maker must be far away from the heat source, such as a bake oven、 electric cooker, etc.
-
Page 11: Power Supply
POWER SUPPLY a、Select the proper power supply according to the voltage and power on the nameplate. b、Connect the power wire and supply, ensuring the yellow and green wires were connected with the ground wire firmly. Caution: a.For safety, ensure the ground connection is in good condition. b.All the exterior wires and other appliances must confirm with national standard. - Page 12 Take out the water supply pipe from accessory bag, connect pipe’s double ends to the water supply valve and water faucet. First, sleeve the connector 1 to the water faucet, then join one end of water supply pipe which has steel balls to the connector 1(hang on this water supply pipe’s end, loose it after being connected to the connector 1), and connect the other end which is attached with a screw to the water supply valve, the valve also has a screw in its end, screw down the valve in...
- Page 13 SERVICE INSTRUCTION 1.Operation process First, turn on the water faucet, power, and water supply valve, then fill the sink with water, and turn off the faucet when the sink is filled with appropriate water. 2. Ice-make process After several minutes, the water pump starts work, and the water will be pumped and flowed through the ice model evenly.
- Page 14 B、The fan motor for condenser is controlled by temperature, when condenser’s surface temperature is lower, the fan motor will stop, so as to save power; when surface temperature rises up, the fan motor will work again, so fan motor work intermittently during the ice-make process.
- Page 15 press on/off button to turn on the machine under turn off status press the on/off button to exit setting under ice thickness setting and filling water adjust status Mode button: Switch the ice making program Clean / Set Button: Press to clean status under machine turn off status +/reservation button: press to ice thickness adjust under pressure equilibrium、making ice、unload ice、...
-
Page 16: Daily Cleaning And Maintenance
forty-five minutes, and the machine will start again. DAILY CLEANING AND MAINTENANCE Clearance of side panels and inner container A、Before cleaning and sanitizing the ice maker, clean up the ice blocks in the cabinet and ensure the power source and water source has been cut off. - Page 17 3. Cleaning the spray water pipe A、Cleaning the ice maker: The spray water pipe must be cleaned once per half a year. When you clean it, firstly open the front cover, take out the spray pipe, and then scour off the scum till the every hole is unblocked.
-
Page 18: Troubleshooting
B、After finishing washing, confirm the place of the float ball: If the float ball is on the bottom and the machine is on, this condition is normal, the program will turn into pressure balance process, the water level will be controlled automatically; If the float ball is on the upper position and the machine stops, it means that there are some problems with the water level sensor, water pump or drain valve. - Page 19 overflow. broken Water level sensor is broken replace it No water flowing Water pump is broken replace it on to the ice PC board is broken replace it model The ice block is The surface of condenser is clean it thin covered with dust.
- Page 20 Technical Support and E-Warranty Certificate www.vevor.com/support Made In China...
Need help?
Do you have a question about the LB360TA and is the answer not in the manual?
Questions and answers