Related Manuals for Toro 79336
Summary of Contents for Toro 79336
- Page 1 Form No. 3372-413 Rev C 42in Bagger TimeCutter ® MX Series Riding Mower Model No. 79336—Serial No. 312000001 and Up *3372-413* C Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Safety and Instructional Decals ......... 4 Setup ................5 You may contact Toro directly at www.Toro.com for product 1 Installing the Weight..........6 and accessory information, help finding a dealer, or to register 2 Installing the Bagger Frame ........8 your product. -
Page 3: Safety
Follow the attachment manufacturer's recommendation for weight limits for towed equipment and towing on slopes. The following list contains safety information specific to Toro products and other safety information you must know. • Never allow children or others in or on towed equipment. -
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 109-6809 1. Crushing hazard of hand—do not remove the whole bagger from the machine; open the bagger top and then remove the bag(s) from the bagger. -
Page 5: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Bolt (3/8 x 1-1/4 inches) Lock nut (3/8 inch) Weight mounting bracket, left Weight mounting bracket, right Washers Install the weight. Weight holding bracket Bolt (3/8 x 1 inch) Flat weight Suitcase weight... -
Page 6: Installing The Weight
Installing the Weight Parts needed for this procedure: Bolt (3/8 x 1-1/4 inches) Lock nut (3/8 inch) Weight mounting bracket, left G014875 Weight mounting bracket, right Figure 3 Washers Weight holding bracket 1. Front right caster (castor 3. Bolt (3/8 x 1 inch) fork and wheel not shown Bolt (3/8 x 1 inch) for clarity) - Page 7 the forward fasteners in the foot assist lift pedal bracket. Secure the bracket using two bolts and two lock nuts (Figure 7). One locknut is from loose parts and the other is reused from earlier removal. G014878 Figure 5 1. Locknut (3/8 inch), existing 5. Hole, existing in frame G014883 2.
-
Page 8: Installing The Bagger Frame
7. Install a flat weight to the holding bracket and move it rearward, flush with the bracket (Figure 9). Installing the Bagger Frame Parts needed for this procedure: Bagger frame support bracket Support spacer plate Self tapping screw (5/16 x 3/4 inch) Bolt (5/16 x 1 inch) Lock nut (5/16 inch) Angled bracket... - Page 9 G010578 G014884 Figure 11 1. Support bracket 2. Self tapping screws (5/16 x 3/4 inch) Figure 13 3. Install the angled bagger bracket to the engine guard 1. Bagger frame 4. Hair pin using two carriage bolts (5/16 x 3/4 inch) and two 2.
-
Page 10: Assembling The Bagger Top
Assembling the Bagger Top Installing the Bagger Top Parts needed for this procedure: Parts needed for this procedure: Bagger top Grass Bag Bagger screen Upper bagger tube Procedure Procedure Turn the bagger top over. Install the screen as shown in 1. -
Page 11: Installing The Chute
2. Lift the bagger top and install the bags by sliding the bag frame hooks onto the retaining brackets (Figure 17). Installing the Chute Parts needed for this procedure: Chute Knobs Baffle Carriage bolt (5/16 x 1-3/8 inches) Flange nut (5/16 inch) Flat washers (5/16 inch) Procedure 1. - Page 12 3. Install the new baffle with a carriage bolt (5/16 x 1 inch) and nut (5/16 inch) from the previously removed baffle (Figure 20). Use a new bolt (5/16 x 1-3/8 inches) and flange nut (5/16 inch) to secure one side of the baffle (Figure 20).
-
Page 13: Connecting With The Discharge Tube
Connecting with the Discharge Tube No Parts Required Procedure 1. Slide the curved end of the discharge tube into the opening in the bagger top (Figure 23). G010641 g017825 Figure 22 1. Chute 3. Retaining clasp (welded to mower deck) 2. -
Page 14: Operation
Operation the chute snaps over the peg on the discharge tube to secure it (Figure 23). Note: Determine the left and right sides of the machine 3. After the bagger installation, install the wire onto the from the normal operating position. spark plug(s). -
Page 15: Clearing Obstructions From The Bagger
Clearing Obstructions from the Bagger 1. Park the machine on a level surface and disengage the blade control switch. 2. Move the motion control levers outward to the neutral lock position, stop the engine, remove the key, set the parking brake and wait for all moving parts to stop before leaving the operating position. -
Page 16: Operating Tips
Operating Tips CAUTION As the bagger fills, extra weight is added to the back Tips for Bagging of the machine. If you stop and start suddenly on hills, you may lose steering control or the machine may tip. Size • Do not start or stop suddenly when going uphill Remember that the mower is longer and wider with this or downhill. -
Page 17: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Inspect the bagger After the first 10 hours • Clean the bagger Before each use or daily •... -
Page 18: Caring For The Grass Bags
Caring for the Grass Bags Storage Washing the grass bags is not recommended. Storing the Bagger Attachment To prevent rapid deterioration of the bag material, store the bags where they will dry completely after each use. 1. Clean the bagger attachment; refer to Cleaning the Bagger Attachment. - Page 19 Notes:...
- Page 20 Countries Other than the United States or Canada Customers who have purchased Toro products outside the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.