Table of Contents
Advertisement
Quick Links
To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
Bagger
TITAN
®
ZX and MX Series Riding Mower
Model No. 79328—Serial No. 312000001 and Up
This kit requires the simultaneous installation
of other kits to function properly. Contact
your Authorized Service Dealer to obtain the
corresponding necessary parts. For more
information, visit us at www.Toro.com.
Form No. 3372-320 Rev A
Original Instructions (EN)
Advertisement
Table of Contents
Related Manuals for Toro TITAN ZX Series
Summary of Contents for Toro TITAN ZX Series
- Page 1 Contact your Authorized Service Dealer to obtain the corresponding necessary parts. For more information, visit us at www.Toro.com. To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Contents and product damage. You are responsible for operating the product properly and safely. Introduction..............2 You may contact Toro directly at www.Toro.com for Safety ................3 product and accessory information, help finding a dealer, Towing Safety............3 or to register your product. -
Page 3: Safety
Towing Safety Safety • Do not attach towed equipment except at the hitch point. DANGER • Follow the attachment manufacturer's Engines can become hot when they are operating. recommendation for weight limits for towed Severe burns can occur from contacting hot equipment and towing on slopes. -
Page 4: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Bagger frame support bracket Support spacer plate Self tapping screw (5/16 x 3/4 inch) Bolt (5/16 x 2-1/2 inch) Lock nut (5/16 inch) Install the bagger frame. -
Page 5: Assembling The Bagger Top
G016263 Figure 4 1. Support bracket 2. Self tapping screws (5/16 x 3/4 inch) G010581 3. Remove the fasteners securing the existing Figure 6 rectangular spacer plate from the top of the engine Left side shown frame and remove the plate, if so equipped. 1. -
Page 6: Installing The Bagger Top
Assembling the Bagger Top Installing the Bagger Top Parts needed for this procedure: Parts needed for this procedure: Bagger top Circular cotter pin Bagger screen Procedure Procedure 1. Install the bagger top to the bagger frame. Slide Turn the bagger top over. Install the screen as shown in the brackets over the posts in the bagger frame and Figure 7 so it slopes down toward the collection bags. -
Page 7: Completing The Installation
Contact your Authorized Service Dealer to obtain the corresponding necessary parts. For more information, visit us at www.Toro.com. Once the Finishing Kit is installed, use the following Operation and Maintenance sections for use and care of the entire bagger attachment. -
Page 8: Operation
Operation Note: Determine the left and right sides of the machine from the normal operating position. WARNING To avoid personal injury, follow these procedures: • Become familiar with all operating and safety instructions in the Operator's Manual for the mower before using this attachment. •... -
Page 9: Removing The Bagger
Removing the Bagger reduce the load on the engine and reduces the chance of plugging the chute and discharge tube. CAUTION Bagging Speed Failing to remove the front bagger weights and operating the machine without the bagger Most often you will bag with the mower throttle in attachment may cause an unstable condition which the Fast position and drive at a normal ground speed. -
Page 10: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Inspect the bagger After the first 10 hours • Clean the bagger Before each use or daily •... -
Page 11: Inspecting The Mower Blades
Inspecting the Mower Blades Storage Inspect the mower blades regularly and whenever a Storing the Bagger Attachment blade strikes a foreign object. 1. Clean the bagger attachment; refer to Cleaning the If the blades are badly worn or damaged, install new Bagger Attachment. - Page 12 Countries Other than the United States or Canada Customers who have purchased Toro products outside the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.