Download
Share
Print this page
  1. Manuals
  2. Brands
  3. motogadget Manuals
  4. Motorcycle Accessories
  5. motoscope pro
  6. Instruction manual

motogadget motoscope pro Instruction Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Instruction Manual
motoscope pro
Multi-purpose instrument
EN
V1.0

Advertisement

loading
Need help?

Need help?

Do you have a question about the motoscope pro and is the answer not in the manual?

Questions and answers

Related Manuals for motogadget motoscope pro

Summary of Contents for motogadget motoscope pro

  • Page 1 Instruction Manual motoscope pro Multi-purpose instrument V1.0...
  • Page 2 Thank you for purchasing a quality product from motogadget. The motoscope pro was developed in Germany and is elaborately handcrafted in Berlin. Please read the following information and recommendations thoroughly and follow these in- structions during installations and use of the product. No liability shall be assumde by motoga- dget for damage or defects resulting from negligence or failure to follow the operating and installation guide.

  • Page 3: Checking The Delivery

    1 Checking the delivery Every motogadget product is delivered in perfect working order. Please check that the goods you receive have not been damaged in transit. If there is any damage or the packaging has been opened, please contact us immediately. Our general terms and conditions apply. If a return is agreed with us, please ensure that we only accept goods in their original packaging and without signs of use within the statutory periods.

  • Page 4: Technical Data

    2.1 Duty of registration / ABE The motoscope pro has a general operating permit (ABE) and therefore does not need to be entered in the vehicle documents. The ABE is marked „KBA 91261“ on the back of the device. You can fi nd the document here: https://manuals.motogadget.com/motoscope-pro/en/...

  • Page 5: Safety Advice

    4 Safety Advice • BEFORE CARRYING OUT ANY WORK ON THE VEHICLE‘S ELECTRICAL SYSTEM, DISCONNECT THE BATTERY. TO DO THIS, FIRST DISCONNECT THE NEGATIVE TERMINAL THEN DISCONNECT THE POSITIVE TERMINAL. WHEN RECONNEC- TING PROCEED IN REVERSE ORDER. • ENSURE THAT THE VEHICLE IS STABLE BEFORE STARTING THE INSTALLATION WORK.
  • Page 6 5 Plug & Ride The Plug&Ride versions of the motoscope pro are equipped with a suitable vehicle plug and moun- ting plate. No adjustments need to be made to the instrument. Only the approved vehicle models and model years are compatible.
  • Page 7 1 Checking the delivery Every motogadget product is delivered in perfect and functionally tested condition. Please check the goods you have received for transport damage. If there is any damage or if the packaging has been opened, please contact us immediately. Our general terms and conditions of business and delivery apply in this respect.
  • Page 8 Breakout Box yellow Tachometer to ignition coil clamp 1 (switched ground from ignitionbox) DO NOT CONNECT TO HIGH VOLTAGE PARTS If use with CDI-Ignition, a motogadget ignition pickup is required (SKU 9000001, sold separately) purple CAN BUS do not connect blue...
  • Page 9 7.2 Battery and power supply The motoscope pro works with voltages from 9V to 15V DC. Operation on vehicles without a 12V battery in the vehicle electrical system is not possible. It cannot be used on vehicles with a positive battery terminal on the vehicle frame.
  • Page 10 1.6 Nm, use screw adhesive (medium strength). One cable of the sensor is connected to ground, the other to the white cable of the motoscope pro. The magnet demagnetizes at temperatures above 100°C (hot brake system).

  • Page 11: Operation

    Once all parts are securely fi tted and correctly connected, the battery can be reconnected. Switch on the on-board voltage, the display should light up and the word “motogadget” should appear. If this is not the case, switch off the ignition and systematically check all instrument connections.
  • Page 12 The motoscope pro has a large main display and a small secondary display. The gear indicator is located to the right of the small display. There are also 4 indicator lights for indi- cators (green), high beam (blue), neutral (green) and warning light (red). The Engine RPM is display- ed graphically by a bar graph.
  • Page 13 Menu diagramm...

  • Page 14: Display Values

    10.1 Display values SPEED Speed display from 0 to 999 km/h or mph. If you switch to another display on the large display and the vehicle is moving, the system auto- matically returns to the SPEED display after a certain time. To do this, the ABACK function must be activated in the setup.
  • Page 15 VOLT Display of the on-board voltage from 9-16V. If the voltage falls below a defi ned value, the warning message LOW VOLTAGE can be generated. ACCEL (acceleration) Display of the current acceleration in G. The value of 9.81 m/s² corresponds to one G. If the acceleration is negative (braking), a minus sign appears in front of the display value.
  • Page 16 max. +ACCEL Display of the maximum positive acceleration achieved. This value is reset with button stage 3. max. -ACCEL Display of the maximum negative acceleration achieved. This value is reset with button stage 3. FUEL Breakout box A or B (article 1005040 or 1005041) and the use of a resistor fl oat switch on the vehicle are required.Display of the tank content from 0 - 100%.
  • Page 17 H2O TMP Breakout box B (SKU 1005041) and temperature sensor (article 9001002) required. Displays the water temperature in the range from +40 to +120 °C. Below +40°C „cold“ is displayed, above 120°C „hot“ is displayed. If no sensor is connected, „-“ is displayed. The temperature can also be displayed in °F.
  • Page 18 11 Setup All instrument settings are made in the setup menu. To access it, press the button / touch until the setup menu starts. The setup is divided into the 6 main menus SCREEN1, SCREEN2, PARAM, CONFIG, MESSAGE and SYSTEM. The speed band is used for navigation. The illuminated part of the speed band corre- sponds to the selected menu.
  • Page 19 CLOCK Setting the time. Button level 1 increments the active digit, level 2 alternates between the digits, level 3 exits the menu and returns to the main PARAM menu. CIRC (circumference) This function is used to enter the wheel circumference in millimetres. Button level 1 increments the active digit, level 2 switches to the next digit, level 3 exits the menu and switches back to the main PARAM menu.
  • Page 20 ImpE (input engine) This function is used to set the number of ignition pulses per crankshaft revolution. Button level 1 switches to the next value, level 3 exits the menu and switches back to the main PARAM menu. If the vehicle has several ignition coils, only the pulses of the ignition coil to which the signal cable is connected are relevant.
  • Page 21 UNIT Selection of the display unit for distance (kilometers or miles), temperature (°Celsius or °Fahrenheit) and pressure (bar or PSI). Button lstage 1 switches between distance, temperature and pressure, button stage 2 selects the selected unit, which can then be changed with button stage 1. Button stage 3 switches back to the selection option.
  • Page 22 TOUCH Activate/deactivate the touch sensor for controlling the instrument (as an alternative to the button). Button stage 2 switches between the two options, button stage 1 switches to the next menu item in the CONFIG main menu. DRZ SLP Activate or deactivate the speed range slave pointer. Button stage 2 switches between the two op- tions, button stage 1 switches to the next menu item in the CONFIG main menu.
  • Page 23 ABACK is deactivated (00s). Only in this case will the current screen be displayed again after swit- ching motoscope pro off and on. Button stage 1 is used to select between 00, 10, 20, 30s. Button stage 3 exit the menu back to the main menu CONFIG.
  • Page 24 11.5 MESSAGE Confi guration of error messages. A error message is shown in the small display with a fl ashing warning light. Confi rm with button stage 2, shows ACKN (acknowledge) briefl y. The error message disappears and the warning light stay lit. The error message is displayed again after a instrument restart.
  • Page 25 H2O TMP If a water temperature sensor is used with breakout box B, a temperature can be defi ned in this menu, above which the message H2O HOT is displayed. In this menu, button stage 1 increases the selected digit by one, button stage 2 changes the digit and button stage 3 exits the menu. The value 000°C deactivates the message.
  • Page 26 AIR TMP If an air temperature sensor is used with breakout box B, a temperature can be defi ned in this menu below which the message AIR COLD is displayed. In this menu, button stage 1 increases the selected digit by one, button stage 2 changes the digit and button stage 3 exits the menu. The value 00.0°C deactivates the message.
  • Page 27 1 or 3. VERSION Displays the fi rmware version of the motoscope pro and the connected breakout box. 11.7 CAN - BUS (old version of the motoscope pro only) The CAN-BUS interface is confi gured in this menu. If no CAN interface is used, the „OFF“ option must be choosen.

  • Page 28: Troubleshooting

    12 Safety advices for use of the motoscope pro in puplic trafi c Please do not allow the instrument to distract you from road traffi c. As the user, you are responsible for the correct setting of all device parameters and the correct installation of all add-on parts. The installation of all sensors and the input of parameters must be carried out with the utmost care, as the accuracy of the display depends on this.
  • Page 29 Disconnect all connections to the instrument. • Connect battery positive terminal with brown and red cable. Connect battery negative terminal with black cable. motoscope pro display must light up and „motogadget“ must appear, if this is not the case, check voltage source and polarity. •...
  • Page 30 14 Appendix 14.1 Wiring diagram...
  • Page 31 14.2 Dimensions...
  • Page 32 Strip 3 mm of insulation from the cable to be connected. The stripped cable end is bent and inserted into the wire end ferrule. The prepared cable is then screwed to the respective screw terminal. Only the motogadget temperature and pressure sensors can be used.
  • Page 33 A relay with a coil value of 70 to 150 Ohm must be connected as shown in the following illustration. Alternatively, the motogadget mo.relay can be used together with the motogadget load resistor. Hot wire tank sensors are very sluggish, so wait at least 10 minutes between connecting the empty tank and the full tank.
  • Page 34 14.4 Setup Menu Diagramm...
  • Page 35 14.5 List of tire rolling circumferences front wheel tire sizes and circumference settings 16´´ tire inner diameter tire size circumference (mm) tire size circumference (mm) 100/90 16 1770 130/70 16 1776 110/90 16 1824 130/90 16 1933 120/80 16 1806 150/80 16 1951 120/90 16...
  • Page 36 rear wheel tire sizes and circumference settings 15´´ tire inner diameter tire size circumference (mm) Reifengröße circumference (mm) 100/90 15 1770 140/80 15 1827 110/90 15 1824 140/90 15 1912 120/80 15 1806 170/80 15 1972 120/90 15 1878 180/70 15 1912 130/70 15 1776...