Electronic Protection System; Wall Mounting - Craftsman CMCPS520 Instruction Manual

ENgliSh
hot/Cold Pack Delay
When the charger detects a battery pack that is too hot
or too cold, it automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery pack has reached an
appropriate temperature. The charger then automatically
switches to the pack charging mode. This feature ensures
maximum battery pack life.
A cold battery pack may charge at a slower rate than a warm
battery pack.
The hot/cold pack delay will be indicated by the green
light(s) continuing to blink and with the red light
continuously ON. Once the battery pack has reached an
appropriate temperature, the red light will turn OFF and the
charger will resume the charging procedure.

Electronic Protection System

Li‑Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to be recharged.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature
is between 65 °F – 75 °F (18 ° C– 24 °C). DO NOT charge
when the battery pack is below 40 °F (4.5 °C), or above
104 °F (40 °C). This is important and will prevent serious
damage to the battery pack.
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger from
the AC outlet before cleaning. Dirt and grease may be
removed from the exterior of the charger using a cloth
or soft non-metallic brush. Do not use water or any
cleaning solutions.

Wall Mounting

Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
8
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
NOTE: Do not attempt to mount CMCB101 charger under a
bench or table.
NOTE: Only mount CMCB101 charger with the charging
lights pointed upward toward the ceiling.
VersaTrack™

WARNING: Do not charge batteries while charger is
hung on Trackwall.
CRAFTSMAN chargers, except the CMCB101, can be
stored on CRAFTSMAN VersaTrack™ Trackwall. Hooks and
accessories are sold separately. Please refer to the VersaTrack™
Trackwall accessory sheet for further information.
NOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwall compatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Remove battery when installing and removing
parts and accessories to prevent accidental operation.

WARNING: Always ensure the collar is completely
threaded on. Not threading the collar completely on could
result in the pole becoming disconnected, creating a
hazardous condition and a possible water leakage point.
Periodically check the connections for tightness.
• The scrubber may be used with just the power head
with the power head and upper pole
base as shown in Fig. D and E.
5
Attaching Power Head (Fig. D)
1. Align the power head arrow
2. Slide the power head
3. Turn the power head collar
above. Ensure the collar is securely tightened. If loose, the
product may not function as intended.
NOTE: Do not overtighten the collar. Overtightening may cause
damage to the tool.
Attaching Pole and Power Head (Fig. D, E)
1. Align the bottom pole arrow
2. Slide the upper pole
3. Turn the pole collar
7
(refer to Fig. D). Ensure the collar is securely tightened. If
loose, the product may not function as intended.
4. Align the power head arrow
5. Slide the power head
together with the
4
with the base arrow
21
onto the base .
3 5
clockwise as seen from
6
with the base arrow
23
onto the base .
4 5
clockwise as seen from above
with the top pole arrow
21
onto the pole.
3
or
3
.
22
.
22
.
24